Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Bulletin of the American Physical Society

Microfabrication of Arrays of Superconducting Transition Edge Sensors for CMB Measurements

Chrystian M. Posada, J. Ding, A. N. Bender, Trupti Khaire, Sergi Lendínez, Samuel Ciocys, Gensheng Wang, Volodymyr G. Yefremenko, S. Padin, J. E. Carlstrom, C. L. Chang, V. Novosad

Published Mar 15, 2016• 0 citations
OpenAlex

Related papers

Development of Superconducting Transition Edge Sensors Array

T. Konno, Sachiko Takasu, K. Hattori +1 more

The Japan Society of Applied Physics•Jan 26, 2021•0 citations

Improvement of Detection Efficiency of Superconducting Transition Edge Sensors Array

T. Konno, Sachiko Takasu, K. Hattori +1 more

The Japan Society of Applied Physics•Jan 28, 2020•0 citations

A 220 GHz superconducting titanium transition edge sensor array developed for cosmic microwave background experiments

Qianghui Luo, Jiaqiang Zhong, Wei Miao +10 more

Abstract In this paper, we report on the design, fabrication, and characterization of a 220 GHz superconducting transition edge sensor (TES) array developed for ground-based cosmic microwave background (CMB) experiments. Unlike conventional TES arrays adopting thermometers made of bilayer superconducting films, the TES array has thermometers made of simpler single-layer titanium (Ti) film deposited on a suspended silicon nitride (SiN x ) membrane. The thermal weak link is realized by releasing the TES’s thermal island including the Ti thermometer by dry etching with xenon difluoride (XeF2), giving a typical thermal conductance of 25 pW K−1. Its thermal-conductance mechanism is further studied by fitting the measured TES’s complex impedance with a three-block thermal model. The dark and optical noise equivalent power (NEP) of a superconducting TES are both measured. Despite existing lens reflection and dielectric loss in the superconducting microstrip line, its typical optical NEP reaches 100 aW Hz−0.5, which meets the sensitivity requirement for ground-based CMB experiments.

Superconductor Science and Technology•Sep 6, 2023•11 citations

Development of a 220 GHz Ti superconducting TES detector array for CMB polarization experiment

Qianghui LUO, Wei MIAO, Feiming Li +7 more

高灵敏度超导相变边缘探测器(Transition Edge Sensor,TES)在宇宙微波背景(Cosmic Microwave Background,CMB)辐射B模偏振探测方面具有重要的应用前景。本文设计并制备了220 GHz频段8×8像元的天线耦合钛超导TES探测器,实验表征了刻蚀前钛超导TES探测器的低温热导和噪声特性。实验结果显示,钛超导TES探测器低温电声相互作用主导热导约为485.4 pW/K,同时钛超导TES探测器噪声等效功率优于5×10-17 W/Hz0.5。原理上,钛超导TES探测器热导在刻蚀后会进一步减小,理论计算出刻蚀后钛超导TES探测器的热导约为38 pW/K,同时,其热起伏等效噪声功率理论值约为9.2×10-18 W/Hz0.5,因此,钛超导TES探测器在刻蚀后的噪声等效功率性能会进一步提升。

Optics and Precision Engineering•Jan 1, 2023•0 citations

Highly-multiplexed microwave SQUID readout using the SLAC Microresonator Radio Frequency (SMuRF) electronics for future CMB and sub-millimeter surveys

Shawn Henderson, Zeeshan Ahmed, David Brown +29 more

The next generation of cryogenic CMB and submillimeter cameras under development require densely instrumented sensor arrays to meet their science goals. The readout of large numbers (~10,000-100,000 per camera) of sub-Kelvin sensors, for instance as proposed for the CMB-S4 experiment, will require substantial improvements in cold and warm readout techniques. To reduce the readout cost per sensor and integration complexity, efforts are presently focused on achieving higher multiplexing density while maintaining readout noise subdominant to intrinsic detector noise and presenting manageable thermal loads. Highly-multiplexed cold readout technologies in active development include Microwave Kinetic Inductance Sensors (MKIDs) and microwave rf-SQUIDs. Both exploit the high quality factors of superconducting microwave resonators to densely channelize sub-Kelvin sensors into the bandwidth of a microwave transmission line. In the case of microwave SQUID multiplexing, arrays of transition-edge sensors (TES) are multiplexed by coupling each TES to its own superconducting microwave resonator through an rf-SQUID. We present advancements in the development of a new warm readout system for microwave SQUID multiplexing, the SLAC Superconducting Microresonator RF electronics, or SMuRF, by adapting SLAC National Accelerator Laboratory's Advanced Telecommunications Computing Architecture (ATCA) FPGA Common Platform. SMuRF aims to read out 4000 microwave SQUID channels between 4 and 8 GHz per RF line. Each compact SMuRF system is built onto a single ATCA carrier blade. Daughter boards on the blade implement RF frequency-division multiplexing using FPGAs, fast DACs and ADCs, and an analog up- and down-conversion chain. The system reads out changes in flux in each resonator-coupled rf-SQUID by monitoring the change in the transmitted amplitude and frequency of RF tones produced at each resonator's fundamental frequency. The SMuRF system is unique in its ability to track each tone, minimizing the total RF power required to readout each resonator, thereby significantly reducing the linearity requirements on the cold and warm readout. Here, we present measurements of the readout noise and linearity of the first full SMuRF system, including a demonstration of closed-loop tone tracking on a 528 channel cryogenic microwave SQUID multiplexer. SMuRF is being explored as a potential readout solution for a number of future CMB projects including Simons Observatory, BICEP Array, CCAT-prime, Ali-CPT, and CMB-S4. In addition, parallel development of the platform is underway to adapt SMuRF to read out both MKID and fast X-ray TES calorimeter arrays.

arXiv:1809.03689•Millimeter, Submillimeter, and Far-Infrared Detectors and Instrumentation for Astronomy XI•Jul 18, 2018•62 citations

Development of superconducting transition edge sensor microcalorimeters

R. M. T. Damayanthi

•Jan 1, 2009•0 citations
Abstract In this paper, we report on the design, fabrication, and characterization of a 220 GHz superconducting transition edge sensor (TES) array developed for ground-based cosmic microwave background (CMB) experiments. Unlike conventional TES arrays adopting thermometers made of bilayer superconducting films, the TES array has thermometers made of simpler single-layer titanium (Ti) film deposited on a suspended silicon nitride (SiN x ) membrane. The thermal weak link is realized by releasing the TES’s thermal island including the Ti thermometer by dry etching with xenon difluoride (XeF2), giving a typical thermal conductance of 25 pW K−1. Its thermal-conductance mechanism is further studied by fitting the measured TES’s complex impedance with a three-block thermal model. The dark and optical noise equivalent power (NEP) of a superconducting TES are both measured. Despite existing lens reflection and dielectric loss in the superconducting microstrip line, its typical optical NEP reaches 100 aW Hz−0.5, which meets the sensitivity requirement for ground-based CMB experiments.
高灵敏度超导相变边缘探测器(Transition Edge Sensor,TES)在宇宙微波背景(Cosmic Microwave Background,CMB)辐射B模偏振探测方面具有重要的应用前景。本文设计并制备了220 GHz频段8×8像元的天线耦合钛超导TES探测器,实验表征了刻蚀前钛超导TES探测器的低温热导和噪声特性。实验结果显示,钛超导TES探测器低温电声相互作用主导热导约为485.4 pW/K,同时钛超导TES探测器噪声等效功率优于5×10-17 W/Hz0.5。原理上,钛超导TES探测器热导在刻蚀后会进一步减小,理论计算出刻蚀后钛超导TES探测器的热导约为38 pW/K,同时,其热起伏等效噪声功率理论值约为9.2×10-18 W/Hz0.5,因此,钛超导TES探测器在刻蚀后的噪声等效功率性能会进一步提升。
The next generation of cryogenic CMB and submillimeter cameras under development require densely instrumented sensor arrays to meet their science goals. The readout of large numbers (~10,000-100,000 per camera) of sub-Kelvin sensors, for instance as proposed for the CMB-S4 experiment, will require substantial improvements in cold and warm readout techniques. To reduce the readout cost per sensor and integration complexity, efforts are presently focused on achieving higher multiplexing density while maintaining readout noise subdominant to intrinsic detector noise and presenting manageable thermal loads. Highly-multiplexed cold readout technologies in active development include Microwave Kinetic Inductance Sensors (MKIDs) and microwave rf-SQUIDs. Both exploit the high quality factors of superconducting microwave resonators to densely channelize sub-Kelvin sensors into the bandwidth of a microwave transmission line. In the case of microwave SQUID multiplexing, arrays of transition-edge sensors (TES) are multiplexed by coupling each TES to its own superconducting microwave resonator through an rf-SQUID. We present advancements in the development of a new warm readout system for microwave SQUID multiplexing, the SLAC Superconducting Microresonator RF electronics, or SMuRF, by adapting SLAC National Accelerator Laboratory's Advanced Telecommunications Computing Architecture (ATCA) FPGA Common Platform. SMuRF aims to read out 4000 microwave SQUID channels between 4 and 8 GHz per RF line. Each compact SMuRF system is built onto a single ATCA carrier blade. Daughter boards on the blade implement RF frequency-division multiplexing using FPGAs, fast DACs and ADCs, and an analog up- and down-conversion chain. The system reads out changes in flux in each resonator-coupled rf-SQUID by monitoring the change in the transmitted amplitude and frequency of RF tones produced at each resonator's fundamental frequency. The SMuRF system is unique in its ability to track each tone, minimizing the total RF power required to readout each resonator, thereby significantly reducing the linearity requirements on the cold and warm readout. Here, we present measurements of the readout noise and linearity of the first full SMuRF system, including a demonstration of closed-loop tone tracking on a 528 channel cryogenic microwave SQUID multiplexer. SMuRF is being explored as a potential readout solution for a number of future CMB projects including Simons Observatory, BICEP Array, CCAT-prime, Ali-CPT, and CMB-S4. In addition, parallel development of the platform is underway to adapt SMuRF to read out both MKID and fast X-ray TES calorimeter arrays.