Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1809.03689 · Millimeter, Submillimeter, and Far-Infrared Detectors and Instrumentation for Astronomy XI

Highly-multiplexed microwave SQUID readout using the SLAC Microresonator Radio Frequency (SMuRF) electronics for future CMB and sub-millimeter surveys

Shawn Henderson, Zeeshan Ahmed, David Brown, Saptarshi Chaudhuri, Hsiao-Mei Cho, John M. D'Ewart, Bradley Dober, John Dusatko, Sofia Fatigoni, J. Frisch, M. Halpern, Gene C. Hilton, Johannes Hubmayr, K. D. Irwin, E. Karpel, S. A. Kernasovskiy, Stephen E. Kuenstner, Chao-Lin L. Kuo, Dale Li, John A. B. Mates, Stephen Robert Smith, Joel Ullom, Leila R. Vale, Daniel D. Van Winkle, Cyndia Yu, Jason E. Austermann, Daniel Becker, Douglas A. Bennett, Shannon M. Duff, Jonathon D. Gard, Carl D. Reintsema, Michael R. Vissers

Published Jul 18, 2018• 62 citations
arXivHTMLPDF

Abstract

The next generation of cryogenic CMB and submillimeter cameras under development require densely instrumented sensor arrays to meet their science goals. The readout of large numbers (~10,000-100,000 per camera) of sub-Kelvin sensors, for instance as proposed for the CMB-S4 experiment, will require substantial improvements in cold and warm readout techniques. To reduce the readout cost per sensor and integration complexity, efforts are presently focused on achieving higher multiplexing density while maintaining readout noise subdominant to intrinsic detector noise and presenting manageable thermal loads. Highly-multiplexed cold readout technologies in active development include Microwave Kinetic Inductance Sensors (MKIDs) and microwave rf-SQUIDs. Both exploit the high quality factors of superconducting microwave resonators to densely channelize sub-Kelvin sensors into the bandwidth of a microwave transmission line. In the case of microwave SQUID multiplexing, arrays of transition-edge sensors (TES) are multiplexed by coupling each TES to its own superconducting microwave resonator through an rf-SQUID. We present advancements in the development of a new warm readout system for microwave SQUID multiplexing, the SLAC Superconducting Microresonator RF electronics, or SMuRF, by adapting SLAC National Accelerator Laboratory's Advanced Telecommunications Computing Architecture (ATCA) FPGA Common Platform. SMuRF aims to read out 4000 microwave SQUID channels between 4 and 8 GHz per RF line. Each compact SMuRF system is built onto a single ATCA carrier blade. Daughter boards on the blade implement RF frequency-division multiplexing using FPGAs, fast DACs and ADCs, and an analog up- and down-conversion chain. The system reads out changes in flux in each resonator-coupled rf-SQUID by monitoring the change in the transmitted amplitude and frequency of RF tones produced at each resonator's fundamental frequency. The SMuRF system is unique in its ability to track each tone, minimizing the total RF power required to readout each resonator, thereby significantly reducing the linearity requirements on the cold and warm readout. Here, we present measurements of the readout noise and linearity of the first full SMuRF system, including a demonstration of closed-loop tone tracking on a 528 channel cryogenic microwave SQUID multiplexer. SMuRF is being explored as a potential readout solution for a number of future CMB projects including Simons Observatory, BICEP Array, CCAT-prime, Ali-CPT, and CMB-S4. In addition, parallel development of the platform is underway to adapt SMuRF to read out both MKID and fast X-ray TES calorimeter arrays.

DOI
10.1117/12.2314435

Related papers

SLAC microresonator RF (SMuRF) electronics: A tone-tracking readout system for superconducting microwave resonator arrays

Cyndia Yu, Zeeshan Ahmed, J. Frisch +22 more

We describe the newest generation of the SLAC Microresonator RF (SMuRF) electronics, a warm digital control and readout system for microwave-frequency resonator-based cryogenic detector and multiplexer systems, such as microwave superconducting quantum interference device multiplexers (μmux) or microwave kinetic inductance detectors. Ultra-sensitive measurements in particle physics and astronomy increasingly rely on large arrays of cryogenic sensors, which in turn necessitate highly multiplexed readout and accompanying room-temperature electronics. Microwave-frequency resonators are a popular tool for cryogenic multiplexing, with the potential to multiplex thousands of detector channels on one readout line. The SMuRF system provides the capability for reading out up to 3328 channels across a 4-8 GHz bandwidth. Notably, the SMuRF system is unique in its implementation of a closed-loop tone-tracking algorithm that minimizes RF power transmitted to the cold amplifier, substantially relaxing system linearity requirements and effective noise from intermodulation products. Here, we present a description of the hardware, firmware, and software systems of the SMuRF electronics, comparing achieved performance with science-driven design requirements. In particular, we focus on the case of large-channel-count, low-bandwidth applications, but the system has been easily reconfigured for high-bandwidth applications. The system described here has been successfully deployed in lab settings and field sites around the world and is baselined for use on upcoming large-scale observatories.

arXiv:2208.10523•Review of Scientific Instruments•Jan 1, 2023•47 citations

A Low Noise, Low Frequency Subsystem for Cryogenic Sensing

Namit Mishra, Joe Frisch, Jeff Olsen +1 more

In this paper, the design of a warm electronics board to provide non-RF control and bias lines to a warm readout system for cryogenic microwave SQUID (superconducting quantum interface device) multiplexing is presented. That system, the SLAC Microresonator Radio Frequency (SMuRF) platform, is a next-generation control and readout system for superconducting microresonators which can be used for a variety of imaging applications ranging from x-rays to Cosmic Microwave Background (CMB) experiments. Focus is given to circuits biasing the cryogenic Transition-Edge Sensors (TES), providing a flux ramp to align the sensor outputs, and circuits to provide software control of gate and drain biases of RF amplifiers in the SMuRF system. Techniques used to reduce the primary components of low frequency noise present in the SMuRF system will also be discussed.

IEEE Nuclear Science Symposium and Medical Imaging Conference (NSS/MIC)•Nov 5, 2022•0 citations

Readout demonstration of 512 TES bolometers using a single microwave SQUID multiplexer (Conference Presentation)

Bradley Dober, Zeeshan Ahmed, Jason E. Austermann +30 more

To enable the next-generation of bolometric cameras, we are developing the microwave SQUID multiplexer (μMUX). Upcoming receivers such as Simons Observatory, CCAT-prime, BICEP array, Ali-CPT, and CMB-S4 plan to instrument focal planes with 50,000-500,000 sensors. Sensor count is achieved by tiling many 150 mm-diameter densely packed detector arrays into these focal planes. The fabrication and quality of large-format bolometer arrays has been demonstrated and is now mature. In contrast, the readout technology required for next-generation receivers needs development. The sensitivity, low cross-talk, high multiplexing density, and small component size make the μMUX well-suited for this goal. In this approach, the TES signal modulates the inductance of an rf-SQUID that loads a high-Q microwave resonator. The coupled signal therefore modulates the microwave resonance frequency, which may be read out using homodyne techniques. By coupling each resonator to the same microwave feedline, many detectors can be read out on a single coaxial cable pair. The multiplexing density is in practice limited by signal bandwidth, allowable cross-talk, and the digitization bandwidth of room-temperature readout electronics. We present the design and performance of a scalable 64-channel multiplexer chip optimized for bolometric applications. We utilize a new quarter wave resonator design that increases the physical linear density by a factor of two, therefore achieving a smaller footprint for simplified detector packaging. Measurements of this design show 100 kHz resonator bandwidth, uniform 1.8 MHz frequency spacing, and an input referred current noise of 35 pA/√Hz that is well below the level of an optimized, background-limited TES bolometer. Using 8 daisy-chained and frequency scaled chips, we create a 512-channel multiplexer and use it to readout a 512 TES-bolometer array. We present the results of this large-scale μMUX demonstration including system yield, signal cross-talk, and an analysis of noise in various TES bias configurations. The result demonstrates the multiplexing density required to read out 2,000 sensors between 4-8 GHz.

Millimeter, Submillimeter, and Far-Infrared Detectors and Instrumentation for Astronomy XI•Jul 10, 2018•1 citation

Characterization of the RF Board for microwave SQUID multiplexing readout electronics

Junbo Wang, Jianing Dong, Zhekai Cheng +1 more

Microwave SQUID multiplexing ($μ$MUX) is a widely used readout technique for large-scale transition-edge sensor (TES) arrays. It uses radio-frequency (RF) probe tones to interrogate cryogenic resonators, requiring frequency conversion between the baseband electronics and the cryogenic RF signal chain. This work describes the RF Board, a room-temperature frequency-conversion board deployed in the AliCPT $μ$MUX readout system. The board up-converts 0-4 GHz baseband I/Q signals to the 4-8 GHz RF band for injection into the cryogenic chain and down-converts returned RF signals to baseband I/Q for ADC digitization. For the current 1000-tone operation, with a DAC output tone power of -30 dBm/tone, the required power windows are -35 to -25 dBm/tone for the RF tones transmitted to the cryostat and -45 to -35 dBm/tone at the ADC input for the returned tones. The RF Board is characterized using swept single-tone measurements covering up-conversion, down-conversion, and RF loopback. Based on these measurements, the RF output power is calculated to be -31.06 to -25.53 dBm, satisfying the RF output window. Assuming a representative cryogenic-chain transmission of -40 dB, the loopback result gives an estimated returned power of -45 to -35 dBm, within the target range. These results show that the RF Board meets the wideband frequency-conversion and tone-power requirements for the $μ$MUX readout system.

arXiv:2606.28901•Jun 27, 2026•0 citations

Superconducting Microwave Resonator Arrays for Submillimeter/Far-infrared Imaging

Omid Noroozian

Superconducting microwave resonators have the potential to revolutionize submillimeter and far-infrared astronomy, and with it our understanding of the universe. The field of low-temperature detector technology has reached a point where extremely sensitive devices like transition-edge sensors are now capable of detecting radiation limited by the background noise of the universe. However, the size of these detector arrays are limited to only a few thousand pixels. This is because of the cost and complexity of fabricating large-scale arrays of these detectors that can reach up to 10 lithographic levels on chip, and the complicated SQUID-based multiplexing circuitry and wiring for readout of each detector. In order to make substantial progress, next- generation ground-based telescopes such as CCAT or future space telescopes require focal planes with large-scale detector arrays of 104–106 pixels. Arrays using microwave kinetic inductance detectors (MKID) are a potential solution. These arrays can be easily made with a single layer of superconducting metal film deposited on a silicon substrate and pattered using conventional optical lithography. Furthermore, MKIDs are inherently multiplexable in the frequency domain, allowing ∼ 103 detectors to be read out using a single coaxial transmission line and cryogenic amplifier, drastically reducing cost and complexity. An MKID uses the change in the microwave surface impedance of a superconducting thin-film microresonator to detect photons. Absorption of photons in the superconductor breaks Cooper pairs into quasiparticles, changing the complex surface impedance, which results in a perturbation of resonator frequency and quality factor. For excitation and readout, the resonator is weakly coupled to a transmission line. The complex amplitude of a microwave probe signal tuned on-resonance and transmitted on the feedline past the resonator is perturbed as photons are absorbed in the superconductor. The perturbation can be detected using a cryogenic amplifier and subsequent homodyne mixing at room temperature. In an array of MKIDs, all the resonators are coupled to a shared feedline and are tuned to slightly different frequencies. They can be read out simultaneously using a comb of frequencies generated and measured using digital techniques. This thesis documents an effort to demonstrate the basic operation of ∼ 256 pixel arrays of lumped-element MKIDs made from superconducting TiNx on silicon. The resonators are designed and simulated for optimum operation. Various properties of the resonators and arrays are measured and compared to theoretical expectations. A particularly exciting observation is the extremely high quality factors (∼ 3 × 107) of our TiNx resonators which is essential for ultra-high sensitivity. The arrays are tightly packed both in space and in frequency which is desirable for larger full-size arrays. However, this can cause a serious problem in terms of microwave crosstalk between neighboring pixels. We show that by properly designing the resonator geometry, crosstalk can be eliminated; this is supported by our measurement results. We also tackle the problem of excess frequency noise in MKIDs. Intrinsic noise in the form of an excess resonance frequency jitter exists in planar superconducting resonators that are made on dielectric substrates. We conclusively show that this noise is due to fluctuations of the resonator capacitance. In turn, the capacitance fluctuations are thought to be driven by two-level system (TLS) fluctuators in a thin layer on the surface of the device. With a modified resonator design we demonstrate with measurements that this noise can be substantially reduced. An optimized version of this resonator was designed for the multiwavelength submillimeter kinetic inductance camera (MUSIC) instrument for the Caltech Submillimeter Observatory.

•Jun 12, 2012•14 citations

Development of Microwave SQUID Multiplexer for Readout of Transition-Edge Sensor Array

Zhi-Fa Feng, Xianfeng Zhou, Wen Zhang +12 more

Superconducting transition-edge sensors (TESs) with high sensitivity can detect electromagnetic wave radiations from millimeter/submillimeter, optical to x/γ rays, and have been successfully used in many fields. To improve detection efficiency and sensitivity, large-scale TES arrays are required in combination with multiplexing readout electronics. Compared to other multiplexing schemes, microwave SQUID multiplexing (μMUX), consisting of high-quality microwave superconducting resonators and RF SQUIDs, is most suitable since it provides a wider bandwidth (GHz) and consequently higher multiplexing factor. We designed two types of circuits with different mutual inductances (MT) between the resonator and the RF SQUID: 2.3 pH for the weak-coupling channel and 6.5 pH for the strong- coupling channel. The resonator and RF SQUID washers made of 150 nm Nb are first fabricated by magnetron-sputtering and reactive ion etching (RIE), followed by deposition of Nb/Al-AlOx/Nb trilayer and definition of the Josephson junctions of the RF SQUIDs. This work presents a μMUX demonstration chip with five channels with Q1values of 787 and 3626, and the measured frequency shifts (Δfpp) of ∼500 kHz and 4 MHz for the weak- and strong-coupling channels, respectively. The open-loop equivalent noise current, obtained from the measured phase noise and resonator responsivity, is ∼80 pA/ √Hz with the strong-coupling channel.

IEEE Transactions on Applied Superconductivity•Jan 14, 2026•2 citations
The next generation of cryogenic CMB and submillimeter cameras under development require densely instrumented sensor arrays to meet their science goals. The readout of large numbers (~10,000-100,000 per camera) of sub-Kelvin sensors, for instance as proposed for the CMB-S4 experiment, will require substantial improvements in cold and warm readout techniques. To reduce the readout cost per sensor and integration complexity, efforts are presently focused on achieving higher multiplexing density while maintaining readout noise subdominant to intrinsic detector noise and presenting manageable thermal loads. Highly-multiplexed cold readout technologies in active development include Microwave Kinetic Inductance Sensors (MKIDs) and microwave rf-SQUIDs. Both exploit the high quality factors of superconducting microwave resonators to densely channelize sub-Kelvin sensors into the bandwidth of a microwave transmission line. In the case of microwave SQUID multiplexing, arrays of transition-edge sensors (TES) are multiplexed by coupling each TES to its own superconducting microwave resonator through an rf-SQUID. We present advancements in the development of a new warm readout system for microwave SQUID multiplexing, the SLAC Superconducting Microresonator RF electronics, or SMuRF, by adapting SLAC National Accelerator Laboratory's Advanced Telecommunications Computing Architecture (ATCA) FPGA Common Platform. SMuRF aims to read out 4000 microwave SQUID channels between 4 and 8 GHz per RF line. Each compact SMuRF system is built onto a single ATCA carrier blade. Daughter boards on the blade implement RF frequency-division multiplexing using FPGAs, fast DACs and ADCs, and an analog up- and down-conversion chain. The system reads out changes in flux in each resonator-coupled rf-SQUID by monitoring the change in the transmitted amplitude and frequency of RF tones produced at each resonator's fundamental frequency. The SMuRF system is unique in its ability to track each tone, minimizing the total RF power required to readout each resonator, thereby significantly reducing the linearity requirements on the cold and warm readout. Here, we present measurements of the readout noise and linearity of the first full SMuRF system, including a demonstration of closed-loop tone tracking on a 528 channel cryogenic microwave SQUID multiplexer. SMuRF is being explored as a potential readout solution for a number of future CMB projects including Simons Observatory, BICEP Array, CCAT-prime, Ali-CPT, and CMB-S4. In addition, parallel development of the platform is underway to adapt SMuRF to read out both MKID and fast X-ray TES calorimeter arrays.
We describe the newest generation of the SLAC Microresonator RF (SMuRF) electronics, a warm digital control and readout system for microwave-frequency resonator-based cryogenic detector and multiplexer systems, such as microwave superconducting quantum interference device multiplexers (μmux) or microwave kinetic inductance detectors. Ultra-sensitive measurements in particle physics and astronomy increasingly rely on large arrays of cryogenic sensors, which in turn necessitate highly multiplexed readout and accompanying room-temperature electronics. Microwave-frequency resonators are a popular tool for cryogenic multiplexing, with the potential to multiplex thousands of detector channels on one readout line. The SMuRF system provides the capability for reading out up to 3328 channels across a 4-8 GHz bandwidth. Notably, the SMuRF system is unique in its implementation of a closed-loop tone-tracking algorithm that minimizes RF power transmitted to the cold amplifier, substantially relaxing system linearity requirements and effective noise from intermodulation products. Here, we present a description of the hardware, firmware, and software systems of the SMuRF electronics, comparing achieved performance with science-driven design requirements. In particular, we focus on the case of large-channel-count, low-bandwidth applications, but the system has been easily reconfigured for high-bandwidth applications. The system described here has been successfully deployed in lab settings and field sites around the world and is baselined for use on upcoming large-scale observatories.
In this paper, the design of a warm electronics board to provide non-RF control and bias lines to a warm readout system for cryogenic microwave SQUID (superconducting quantum interface device) multiplexing is presented. That system, the SLAC Microresonator Radio Frequency (SMuRF) platform, is a next-generation control and readout system for superconducting microresonators which can be used for a variety of imaging applications ranging from x-rays to Cosmic Microwave Background (CMB) experiments. Focus is given to circuits biasing the cryogenic Transition-Edge Sensors (TES), providing a flux ramp to align the sensor outputs, and circuits to provide software control of gate and drain biases of RF amplifiers in the SMuRF system. Techniques used to reduce the primary components of low frequency noise present in the SMuRF system will also be discussed.
To enable the next-generation of bolometric cameras, we are developing the microwave SQUID multiplexer (μMUX). Upcoming receivers such as Simons Observatory, CCAT-prime, BICEP array, Ali-CPT, and CMB-S4 plan to instrument focal planes with 50,000-500,000 sensors. Sensor count is achieved by tiling many 150 mm-diameter densely packed detector arrays into these focal planes. The fabrication and quality of large-format bolometer arrays has been demonstrated and is now mature. In contrast, the readout technology required for next-generation receivers needs development. The sensitivity, low cross-talk, high multiplexing density, and small component size make the μMUX well-suited for this goal. In this approach, the TES signal modulates the inductance of an rf-SQUID that loads a high-Q microwave resonator. The coupled signal therefore modulates the microwave resonance frequency, which may be read out using homodyne techniques. By coupling each resonator to the same microwave feedline, many detectors can be read out on a single coaxial cable pair. The multiplexing density is in practice limited by signal bandwidth, allowable cross-talk, and the digitization bandwidth of room-temperature readout electronics. We present the design and performance of a scalable 64-channel multiplexer chip optimized for bolometric applications. We utilize a new quarter wave resonator design that increases the physical linear density by a factor of two, therefore achieving a smaller footprint for simplified detector packaging. Measurements of this design show 100 kHz resonator bandwidth, uniform 1.8 MHz frequency spacing, and an input referred current noise of 35 pA/√Hz that is well below the level of an optimized, background-limited TES bolometer. Using 8 daisy-chained and frequency scaled chips, we create a 512-channel multiplexer and use it to readout a 512 TES-bolometer array. We present the results of this large-scale μMUX demonstration including system yield, signal cross-talk, and an analysis of noise in various TES bias configurations. The result demonstrates the multiplexing density required to read out 2,000 sensors between 4-8 GHz.
Microwave SQUID multiplexing (μμμMUX) is a widely used readout technique for large-scale transition-edge sensor (TES) arrays. It uses radio-frequency (RF) probe tones to interrogate cryogenic resonators, requiring frequency conversion between the baseband electronics and the cryogenic RF signal chain. This work describes the RF Board, a room-temperature frequency-conversion board deployed in the AliCPT μμμMUX readout system. The board up-converts 0-4 GHz baseband I/Q signals to the 4-8 GHz RF band for injection into the cryogenic chain and down-converts returned RF signals to baseband I/Q for ADC digitization. For the current 1000-tone operation, with a DAC output tone power of -30 dBm/tone, the required power windows are -35 to -25 dBm/tone for the RF tones transmitted to the cryostat and -45 to -35 dBm/tone at the ADC input for the returned tones. The RF Board is characterized using swept single-tone measurements covering up-conversion, down-conversion, and RF loopback. Based on these measurements, the RF output power is calculated to be -31.06 to -25.53 dBm, satisfying the RF output window. Assuming a representative cryogenic-chain transmission of -40 dB, the loopback result gives an estimated returned power of -45 to -35 dBm, within the target range. These results show that the RF Board meets the wideband frequency-conversion and tone-power requirements for the μμμMUX readout system.
Superconducting microwave resonators have the potential to revolutionize submillimeter and far-infrared astronomy, and with it our understanding of the universe. The field of low-temperature detector technology has reached a point where extremely sensitive devices like transition-edge sensors are now capable of detecting radiation limited by the background noise of the universe. However, the size of these detector arrays are limited to only a few thousand pixels. This is because of the cost and complexity of fabricating large-scale arrays of these detectors that can reach up to 10 lithographic levels on chip, and the complicated SQUID-based multiplexing circuitry and wiring for readout of each detector. In order to make substantial progress, next- generation ground-based telescopes such as CCAT or future space telescopes require focal planes with large-scale detector arrays of 104–106 pixels. Arrays using microwave kinetic inductance detectors (MKID) are a potential solution. These arrays can be easily made with a single layer of superconducting metal film deposited on a silicon substrate and pattered using conventional optical lithography. Furthermore, MKIDs are inherently multiplexable in the frequency domain, allowing ∼ 103 detectors to be read out using a single coaxial transmission line and cryogenic amplifier, drastically reducing cost and complexity. An MKID uses the change in the microwave surface impedance of a superconducting thin-film microresonator to detect photons. Absorption of photons in the superconductor breaks Cooper pairs into quasiparticles, changing the complex surface impedance, which results in a perturbation of resonator frequency and quality factor. For excitation and readout, the resonator is weakly coupled to a transmission line. The complex amplitude of a microwave probe signal tuned on-resonance and transmitted on the feedline past the resonator is perturbed as photons are absorbed in the superconductor. The perturbation can be detected using a cryogenic amplifier and subsequent homodyne mixing at room temperature. In an array of MKIDs, all the resonators are coupled to a shared feedline and are tuned to slightly different frequencies. They can be read out simultaneously using a comb of frequencies generated and measured using digital techniques. This thesis documents an effort to demonstrate the basic operation of ∼ 256 pixel arrays of lumped-element MKIDs made from superconducting TiNx on silicon. The resonators are designed and simulated for optimum operation. Various properties of the resonators and arrays are measured and compared to theoretical expectations. A particularly exciting observation is the extremely high quality factors (∼ 3 × 107) of our TiNx resonators which is essential for ultra-high sensitivity. The arrays are tightly packed both in space and in frequency which is desirable for larger full-size arrays. However, this can cause a serious problem in terms of microwave crosstalk between neighboring pixels. We show that by properly designing the resonator geometry, crosstalk can be eliminated; this is supported by our measurement results. We also tackle the problem of excess frequency noise in MKIDs. Intrinsic noise in the form of an excess resonance frequency jitter exists in planar superconducting resonators that are made on dielectric substrates. We conclusively show that this noise is due to fluctuations of the resonator capacitance. In turn, the capacitance fluctuations are thought to be driven by two-level system (TLS) fluctuators in a thin layer on the surface of the device. With a modified resonator design we demonstrate with measurements that this noise can be substantially reduced. An optimized version of this resonator was designed for the multiwavelength submillimeter kinetic inductance camera (MUSIC) instrument for the Caltech Submillimeter Observatory.
Superconducting transition-edge sensors (TESs) with high sensitivity can detect electromagnetic wave radiations from millimeter/submillimeter, optical to x/γ rays, and have been successfully used in many fields. To improve detection efficiency and sensitivity, large-scale TES arrays are required in combination with multiplexing readout electronics. Compared to other multiplexing schemes, microwave SQUID multiplexing (μMUX), consisting of high-quality microwave superconducting resonators and RF SQUIDs, is most suitable since it provides a wider bandwidth (GHz) and consequently higher multiplexing factor. We designed two types of circuits with different mutual inductances (MT) between the resonator and the RF SQUID: 2.3 pH for the weak-coupling channel and 6.5 pH for the strong- coupling channel. The resonator and RF SQUID washers made of 150 nm Nb are first fabricated by magnetron-sputtering and reactive ion etching (RIE), followed by deposition of Nb/Al-AlOx/Nb trilayer and definition of the Josephson junctions of the RF SQUIDs. This work presents a μMUX demonstration chip with five channels with Q1values of 787 and 3626, and the measured frequency shifts (Δfpp) of ∼500 kHz and 4 MHz for the weak- and strong-coupling channels, respectively. The open-loop equivalent noise current, obtained from the measured phase noise and resonator responsivity, is ∼80 pA/ √Hz with the strong-coupling channel.