Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

CRC Press eBooks

Theory of Collimated Atomic Beam Formation

Cyril Bernard Lucas

Published Nov 27, 2013• 0 citations
Publisher

Abstract

If a beam is to be produced from a material that is solid or liquid at laboratory temperature, then it must be converted to a vapour in an oven before it passes through the beam-forming impedance. In the reviews mentioned in Section 1.2, the approach has usually been to give details of numerous designs. In this chapter, we discuss the general design principles, and then the next two chapters become more of a reference source for the evaporation of different substances. We thus include the experience of a large number of experimenters who have needed to heat a liquid or solid substance to form it into an atomic or molecular beam. If the material can be evaporated and raised to a temperature to give the required input pressure at the input to the impedance at a temperature less than about 1500 K, it is usual to describe the heating device as an oven. At higher temperatures, the device is usually called a furnace, but the distinction is not really necessary. Hence we will avoid the term except for thermal dissociation of a molecular species, discussed in Chapter 6, when very high temperatures are usually needed, so a furnace is a more appropriate term. For convenience we will also term a completely different approach, namely, the evaporation of the material by direct electron beam heating of the surface (Section 3.2.5) as an oven. ‘Crucible’ is used by many authors interchangeably with ‘oven,’ but it often implies a container for the material to be evaporated that is placed within a heated envelope.

DOI
10.1201/b16345-9

Related papers

Designing an Atomic Beam

Cyril Bernard Lucas

Generally lower temperatures of evaporation make most aspects of oven design easier than those discussed in Chapter 5 and included in this group are ovens for the production of beams of alkali metals and their salts. Some special techniques are, however, necessary to handle the alkali metals because of their reactivity with moist air, which increases with atomic number Z. One solution is to produce the beam by a reaction of stable substances in the oven and we begin the discussion of the alkali metals with those cases in Section 4.2. We then consider in Section 4.3 more conventional ovens where the material to be evaporated is loaded directly into the oven. In Section 4.4 we turn to the alkali halides, which have problems due to their corrosiveness in the liquid and vapour state. Ovens where an ampoule of material has to be broken are discussed in Section 4.5. Finally in this chapter we discuss recycling ovens, where material that is not formed into a useful beam is returned to the oven.

CRC Press eBooks•Nov 27, 2013•0 citations

Concluding Observations

Cyril Bernard Lucas

In Section 1.1 we introduced the subject of atomic and molecular beam formation by stating that a beam with a cosine distribution is obtained when the beam-forming impedance is a circular orice and that a narrow slit has also been employed to produce an improved beam. Most relevant theoretical papers use the convention of referring to ‘molecules’ for both atoms and molecules, but we continue to retain the consistent use of ‘atoms’ to mean both atoms and molecules unless a distinction is necessary. Following the introduction of the basic equations of the kinetic theory of gases in Section 2.2, the relatively simple expressions for the beam formed by an orice were introduced in Section 2.3. It was also mentioned in Section 1.1 that when the impedance is a single tube a much narrower collimated beam is obtained and that by employing an array of tubes a greatly improved beam intensity is obtained. In this chapter we present the theory of beam formation to include the more difcult case of ow through a tube. We only briey mention calculations that only apply when Γ ≤ 10 where Γ is the ratio of length l to diameter d (Section 2.5). These are of little interest for atomic beam formation, but are needed for calculations of Knudsen cell operation, which are outside the scope of this work. Following the discussion of the basic theory, we present in the next chapter simplications that make the design of an atomic beam and the predictions of its performance easier. However, we warn that an extensive comparison of theoretical results with experiment in Chapter 11 points to an unsatisfactory disagreement between theory and experiment for the beam halfwidth, especially in the case of gaseous rather than vapour beams and also particularly when the beam-forming impedance is a focussing capillary array.

CRC Press eBooks•Nov 27, 2013•0 citations

Atomic oven with rapid thermal response for atom experiments

Weilong Huang, Congjun Zou, Feiyu Dong +3 more

Atomic oven generating controllable atomic beam flux plays a fundamental role in quantum gas experiments. Here, we report a new heater design that can heat up an high temperature atomic oven with fast thermal response. The new heater shows a heating rate improved by 7.65 times comparing to that of the conventional resistive heater while the crucible temperature can heated up to 1200K. With this oven, we generated a collimated ytterbium beam with flux exceeding $10^{14} \text{ atoms/s}$ at 823 K. We believe that our design offers a promising solution for shortening experimental dead time and improve the experiment efficiency in cold atom researches.

physics.atom-phCross-listedarXiv:2607.04393•Jul 7, 2026•0 citations

Other Indications

Cyril Bernard Lucas

Two topics that logically follow a chapter on gases are included here, namely, the recirculation of gases used to form beams and the levitation of solids. This was originally undertaken with gas beams, but we take liberties with the chapter title by including other methods that may prove useful for atomic beam production. Details of the vacuum systems in which the beam is produced, such as pumping and differential pumping, have not, in general, been included when discussing experiments, since these tend to be closely associated with the experiment for which the beam is required. Neither have general vacuum techniques been discussed, since these are covered in the many textbooks devoted to them. We nevertheless include details of methods that have been or could be used to recycle gases used in atomic beam experiments, since these tend not to be included elsewhere. It is also not our practice to discuss atomic beam applications such as those that are covered by the review articles referred to in Section 1.2, but we make an exception for levitation by atomic beams, since we are not aware of any review that includes these. We then add other levitation techniques that might prove useful for producing beams of refractory metals.

CRC Press eBooks•Nov 27, 2013•0 citations

Atomic beam source for the ultracold focused ion beam setup

Brenda R. J. Jansen

In the ultracold FIB project a high brightness ion beam is developed for usage in a focused ion beam (FIB) source. This Focused Ion Beam can be used in applications where milling, imaging and deposition at the nanoscale needs to be done with increasing demands on control and resolution. The generation of the ion beam done in three stage principle. The first stage is the generation of the atomic beam and this is the subject of this work. The following stages first transversely cool and compress the atomic beam by using laser cooling techniques and then ionize and accelerate the atoms to form the ion beam. The generation of the atomic beam is done using a Knudsen cell; an effusive oven containing a vapor of rubidium atoms. The pressure difference between the vapor pressure in the oven and the vacuum outside the oven generates a flow of atoms from the oven to the vacuum. Only atoms that have a low transverse velocity can be captured by the laser cooling stage and will attribute to the ion beam. Therefore it is important to minimize the divergence in the beam and to this extent a collimating tube is used to connect the effusive oven to the vacuum system. The collimating tube minimizes beam divergence and compared to other collimating mechanisms it reduces the amount of rubidium loss, therefore greatly increasing the lifetime of the system.In order to measure the transverse velocity distribution, the transverse beam profile and the total flux, Laser-Induced Fluorescence measurements have been performed. These measurements show that the source generates an atomic beam with a particle flux ranging from 107 s-1 at a source temperature of 60 ºC to 1010 s-1 at a source temperature of 160 ºC. The flux is lower than predicted by theory and the transverse velocity distribution is broader than predicted by theory. However, the particle flux is stable within 1% and the installation of an active temperature controller promises to improve this stability even further. In the ultracold FIB project a high brightness ion beam is developed for usage in a focused ion beam (FIB) source. This Focused Ion Beam can be used in applications where milling, imaging and deposition at the nanoscale needs to be done with increasing demands on control and resolution. The generation of the ion beam done in three stage principle. The first stage is the generation of the atomic beam and this is the subject of this work. The following stages first transversely cool and compress the atomic beam by using laser cooling techniques and then ionize and accelerate the atoms to form the ion beam. The generation of the atomic beam is done using a Knudsen cell; an effusive oven containing a vapor of rubidium atoms. The pressure difference between the vapor pressure in the oven and the vacuum outside the oven generates a flow of atoms from the oven to the vacuum. Only atoms that have a low transverse velocity can be captured by the laser cooling stage and will attribute to the ion beam. Therefore it is important to minimize the divergence in the beam and to this extent a collimating tube is used to connect the effusive oven to the vacuum system. The collimating tube minimizes beam divergence and compared to other collimating mechanisms it reduces the amount of rubidium loss, therefore greatly increasing the lifetime of the system.In order to measure the transverse velocity distribution, the transverse beam profile and the total flux, Laser-Induced Fluorescence measurements have been performed. These measurements show that the source generates an atomic beam with a particle flux ranging from 107 s-1 at a source temperature of 60 ºC to 1010 s-1 at a source temperature of 160 ºC. The flux is lower than predicted by theory and the transverse velocity distribution is broader than predicted by theory. However, the particle flux is stable within 1% and the installation of an active temperature controller promises to improve this stability even further.

•Jan 1, 2013•0 citations

Simple oven design for highly reactive metal beam applications

Luis Bañares, Ángel González Ureña

An oven design suitable for producing stable beams of highly reactive metals is reported. Its attraction is in its simplicity, low cost and versatility in molecular beam and atomic/molecular physics experiments involving highly reactive metals such as rubidium, caesium, etc. An application is described for the case of atomic caesium, where the metal is produced by the chemical reaction Ba(s)+CsCl(s) to BaCl(s)+Cs(v). One of the main advantages of the present design is the use of a thin-walled, stainless steel pipe, as crucible and heater simultaneously, which considerably simplifies its design. With respect to the experimental method, the simplicity in the loading, working and cleaning procedures compared with the use of pure metal should be noted.

Journal of Physics E Scientific Instruments•Dec 1, 1989•6 citations
If a beam is to be produced from a material that is solid or liquid at laboratory temperature, then it must be converted to a vapour in an oven before it passes through the beam-forming impedance. In the reviews mentioned in Section 1.2, the approach has usually been to give details of numerous designs. In this chapter, we discuss the general design principles, and then the next two chapters become more of a reference source for the evaporation of different substances. We thus include the experience of a large number of experimenters who have needed to heat a liquid or solid substance to form it into an atomic or molecular beam. If the material can be evaporated and raised to a temperature to give the required input pressure at the input to the impedance at a temperature less than about 1500 K, it is usual to describe the heating device as an oven. At higher temperatures, the device is usually called a furnace, but the distinction is not really necessary. Hence we will avoid the term except for thermal dissociation of a molecular species, discussed in Chapter 6, when very high temperatures are usually needed, so a furnace is a more appropriate term. For convenience we will also term a completely different approach, namely, the evaporation of the material by direct electron beam heating of the surface (Section 3.2.5) as an oven. ‘Crucible’ is used by many authors interchangeably with ‘oven,’ but it often implies a container for the material to be evaporated that is placed within a heated envelope.
Generally lower temperatures of evaporation make most aspects of oven design easier than those discussed in Chapter 5 and included in this group are ovens for the production of beams of alkali metals and their salts. Some special techniques are, however, necessary to handle the alkali metals because of their reactivity with moist air, which increases with atomic number Z. One solution is to produce the beam by a reaction of stable substances in the oven and we begin the discussion of the alkali metals with those cases in Section 4.2. We then consider in Section 4.3 more conventional ovens where the material to be evaporated is loaded directly into the oven. In Section 4.4 we turn to the alkali halides, which have problems due to their corrosiveness in the liquid and vapour state. Ovens where an ampoule of material has to be broken are discussed in Section 4.5. Finally in this chapter we discuss recycling ovens, where material that is not formed into a useful beam is returned to the oven.
In Section 1.1 we introduced the subject of atomic and molecular beam formation by stating that a beam with a cosine distribution is obtained when the beam-forming impedance is a circular orice and that a narrow slit has also been employed to produce an improved beam. Most relevant theoretical papers use the convention of referring to ‘molecules’ for both atoms and molecules, but we continue to retain the consistent use of ‘atoms’ to mean both atoms and molecules unless a distinction is necessary. Following the introduction of the basic equations of the kinetic theory of gases in Section 2.2, the relatively simple expressions for the beam formed by an orice were introduced in Section 2.3. It was also mentioned in Section 1.1 that when the impedance is a single tube a much narrower collimated beam is obtained and that by employing an array of tubes a greatly improved beam intensity is obtained. In this chapter we present the theory of beam formation to include the more difcult case of ow through a tube. We only briey mention calculations that only apply when Γ ≤ 10 where Γ is the ratio of length l to diameter d (Section 2.5). These are of little interest for atomic beam formation, but are needed for calculations of Knudsen cell operation, which are outside the scope of this work. Following the discussion of the basic theory, we present in the next chapter simplications that make the design of an atomic beam and the predictions of its performance easier. However, we warn that an extensive comparison of theoretical results with experiment in Chapter 11 points to an unsatisfactory disagreement between theory and experiment for the beam halfwidth, especially in the case of gaseous rather than vapour beams and also particularly when the beam-forming impedance is a focussing capillary array.
Atomic oven generating controllable atomic beam flux plays a fundamental role in quantum gas experiments. Here, we report a new heater design that can heat up an high temperature atomic oven with fast thermal response. The new heater shows a heating rate improved by 7.65 times comparing to that of the conventional resistive heater while the crucible temperature can heated up to 1200K. With this oven, we generated a collimated ytterbium beam with flux exceeding 1014 atoms/s10^{14} \text{ atoms/s}1014 atoms/s at 823 K. We believe that our design offers a promising solution for shortening experimental dead time and improve the experiment efficiency in cold atom researches.
Two topics that logically follow a chapter on gases are included here, namely, the recirculation of gases used to form beams and the levitation of solids. This was originally undertaken with gas beams, but we take liberties with the chapter title by including other methods that may prove useful for atomic beam production. Details of the vacuum systems in which the beam is produced, such as pumping and differential pumping, have not, in general, been included when discussing experiments, since these tend to be closely associated with the experiment for which the beam is required. Neither have general vacuum techniques been discussed, since these are covered in the many textbooks devoted to them. We nevertheless include details of methods that have been or could be used to recycle gases used in atomic beam experiments, since these tend not to be included elsewhere. It is also not our practice to discuss atomic beam applications such as those that are covered by the review articles referred to in Section 1.2, but we make an exception for levitation by atomic beams, since we are not aware of any review that includes these. We then add other levitation techniques that might prove useful for producing beams of refractory metals.
In the ultracold FIB project a high brightness ion beam is developed for usage in a focused ion beam (FIB) source. This Focused Ion Beam can be used in applications where milling, imaging and deposition at the nanoscale needs to be done with increasing demands on control and resolution. The generation of the ion beam done in three stage principle. The first stage is the generation of the atomic beam and this is the subject of this work. The following stages first transversely cool and compress the atomic beam by using laser cooling techniques and then ionize and accelerate the atoms to form the ion beam. The generation of the atomic beam is done using a Knudsen cell; an effusive oven containing a vapor of rubidium atoms. The pressure difference between the vapor pressure in the oven and the vacuum outside the oven generates a flow of atoms from the oven to the vacuum. Only atoms that have a low transverse velocity can be captured by the laser cooling stage and will attribute to the ion beam. Therefore it is important to minimize the divergence in the beam and to this extent a collimating tube is used to connect the effusive oven to the vacuum system. The collimating tube minimizes beam divergence and compared to other collimating mechanisms it reduces the amount of rubidium loss, therefore greatly increasing the lifetime of the system.In order to measure the transverse velocity distribution, the transverse beam profile and the total flux, Laser-Induced Fluorescence measurements have been performed. These measurements show that the source generates an atomic beam with a particle flux ranging from 107 s-1 at a source temperature of 60 ºC to 1010 s-1 at a source temperature of 160 ºC. The flux is lower than predicted by theory and the transverse velocity distribution is broader than predicted by theory. However, the particle flux is stable within 1% and the installation of an active temperature controller promises to improve this stability even further. In the ultracold FIB project a high brightness ion beam is developed for usage in a focused ion beam (FIB) source. This Focused Ion Beam can be used in applications where milling, imaging and deposition at the nanoscale needs to be done with increasing demands on control and resolution. The generation of the ion beam done in three stage principle. The first stage is the generation of the atomic beam and this is the subject of this work. The following stages first transversely cool and compress the atomic beam by using laser cooling techniques and then ionize and accelerate the atoms to form the ion beam. The generation of the atomic beam is done using a Knudsen cell; an effusive oven containing a vapor of rubidium atoms. The pressure difference between the vapor pressure in the oven and the vacuum outside the oven generates a flow of atoms from the oven to the vacuum. Only atoms that have a low transverse velocity can be captured by the laser cooling stage and will attribute to the ion beam. Therefore it is important to minimize the divergence in the beam and to this extent a collimating tube is used to connect the effusive oven to the vacuum system. The collimating tube minimizes beam divergence and compared to other collimating mechanisms it reduces the amount of rubidium loss, therefore greatly increasing the lifetime of the system.In order to measure the transverse velocity distribution, the transverse beam profile and the total flux, Laser-Induced Fluorescence measurements have been performed. These measurements show that the source generates an atomic beam with a particle flux ranging from 107 s-1 at a source temperature of 60 ºC to 1010 s-1 at a source temperature of 160 ºC. The flux is lower than predicted by theory and the transverse velocity distribution is broader than predicted by theory. However, the particle flux is stable within 1% and the installation of an active temperature controller promises to improve this stability even further.
An oven design suitable for producing stable beams of highly reactive metals is reported. Its attraction is in its simplicity, low cost and versatility in molecular beam and atomic/molecular physics experiments involving highly reactive metals such as rubidium, caesium, etc. An application is described for the case of atomic caesium, where the metal is produced by the chemical reaction Ba(s)+CsCl(s) to BaCl(s)+Cs(v). One of the main advantages of the present design is the use of a thin-walled, stainless steel pipe, as crucible and heater simultaneously, which considerably simplifies its design. With respect to the experimental method, the simplicity in the loading, working and cleaning procedures compared with the use of pure metal should be noted.