Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Single Photon Generation and Spectroscopy Using Quantum Dots on Optical Nanofibers

Ramachandrarao Yalla

Published Jan 1, 2012• 1 citation
OpenAlex

Abstract

This thesis presents single photon generation and spectroscopy using quantum dots (q-dots) on optical nanofibers. Optical nanofibers are essentially vacuum-clad silica fibers with sub-wavelength diameter, which can support only the propagation of the fundamental mode through the guided mode. Optical nanofibers are realized using adiabatically tapered single mode optical fibers. Experiments were performed by depositing colloidal core-shell type CdSeTe (ZnS) q-dots on the optical nanofiber surface. A method is developed to deposit single q-dots systematically and reproducibly along the optical nanofiber. In the view point of investigation of fluorescence photon emission characteristics for single q-dots on optical nanofibers, the absolute fluorescence photon-count rates channeled into the nanofiber guided modes and the normalized photon correlations at various excitation laser intensities are measured. The results are able to obtain the product between the fluorescence photon channeling efficiency and the quantum efficiency of the single q-dots. However, the channeling efficiency cannot be determined without accurate information on the quantum efficiency of the single q-dots. Therefore, a method is devised to determine the channeling of fluorescence photons from single q-dots into the guided modes by measuring the fluorescence photon-count rates through the guided and radiation modes simultaneously. By measuring for various nanofiber diameters, a maximum channeling efficiency obtained to be 22.0 (±4.8)% at a fiber diameter of 350 nm for an emission wavelength of 780 nm. The measured results completely reproduce the theoretical predictions within the experimental error. We demonstrate in situ measurements of fluorescence quantum efficiency of single q-dots using the present nanofiber technique. We determine fluorescence quantum efficiency of single q-dots accurately by assuming the theoretical values for the channeling efficiency from the product of the channeling efficiency and the quantum efficiency. We demonstrate that one can pick up one q-dot on the nanofiber with fluorescence quantum efficiency higher than the average value measured for an ensemble. Thus, the optical nanofiber method offers a promising way for generating and manipulating single photons. This work should provide a basis for extending the optical nanofiber method to a general technique in quantum optics, which may open new possibilities in quantum information technologies.

Related papers

Efficient Channeling of Fluorescence Photons from Single Quantum Dots into Guided Modes of Optical Nanofiber

Ramachandrarao Yalla, Fam Le Kien, M. Morinaga +1 more

We experimentally demonstrate the efficient channeling of fluorescence photons from single q dots on optical nanofiber into the guided modes by measuring the photon-count rates through the guided and radiation modes simultaneously. We obtain the maximum channeling efficiency to be 22.0(±4.8)% at a fiber diameter of 350 nm for the emission wavelength of 780 nm. The results may open new possibilities in quantum information technologies for generating single photons into single-mode optical fibers.

arXiv:1204.6153•Physical Review Letters•Aug 8, 2012•187 citations

Hybrid System of Optical Nanofiber and Single Quantum Dot for Fiber In-Line Single Photon Generation

Muhammed Shafi Kodakkaden

Hybrid systems of nanophotonic structures and single quantum emitters have emerged as a promising direction for single photon generation in quantum photonic technologies.Strong confinement of the optical field in nanophotonic structures enables photon manipulation far beyond the free space.In this context, tapered optical fibers with sub-wavelength diameter waists, optical nanofibers, provide a unique platform.Regarding the single photon generation, a key advantage is the efficient fiber in-line operation, i.e. photons efficiently emitted into the guided-mode of the nanofiber adiabatically couples to that of a conventional single mode optical fiber with near-unity efficiency.Regarding the emitters for quantum photonics, solid-state emitters at cryogenic temperatures are preferred from the prospect of practical applications in quantum information technologies.In this thesis, a hybrid system of an optical nanofiber (ONF) and a single colloidal CdSe quantum dot (QD) operated at cryogenic temperature is developed and investigated from the viewpoint of fiber in-line single photon generation.Single CdSe core/shell QDs emitting at 640 nm are precisely deposited on the nanofiber surface.An optical cryostat cools the hybrid system to a temperature of 3.7 K via helium buffer-gas cooling, maintaining the high optical transmission of the ONF (94.5%).The photoluminescence (PL) characteristics of the QDs are investigated by observing the emitted photons through the fiber guided-modes.At 3.7 K, the emission spectrum of the single QDs showed two distinct narrow zero-phonon lines (∼350 µeV FWHM) compared to the broad spectral width (60 meV FWHM) at room temperature.viii These lines originate from the neutral and charged states of the QD emitting with near-unity quantum efficiency.The charged QDs are termed as trions.We systematically investigated the emission characteristics of the neutral and the trion states of the QD by spectral, temporal, and photon correlation measurements.The PL decay characteristics of these lines reveal that the upper state of neutral exciton consists of two levels, which effectively results in a fast and slow decay components with decay times of 3.1±0.1 and 153±5 ns, respectively.In contrast, the upper state of trion is one level leading to a single decay process with a decay time of 10.7±0.3 ns.From the viewpoint of single photon generation, the trion with a single upper level is preferable compared to the neutral exciton.Subsequently, a technique to control the occurrence of trion at cryogenic temperatures is developed.It is shown that the trion occurrence can be manipulated by photocharging the QD by exciting well above the band gap.Most notably, we established a method to create permanently charged QDs with all emissions into the trion zero-phonon line.Combining the photocharged single QDs in the hybrid system, we evaluated the performance of the system as an efficient fiber in-line single photon source.We show that the photocharged QDs exhibit a bright photo-stable emission of single photons with near-unity quantum efficiency, narrow spectral width and a fast single decay process.The efficiency of the source is estimated to be 16±2%, with a maximum photon count rate of 1.6±0.2MHz and a high single photon purity of g 2 (0)= 0.11±0.02.The ONF/QD hybrid system could be integrated into the fiber networks paving the way for potential applications in quantum information technologies.The efficiency of the source can be improved by incorporating a cavity structure on the ONF and establish a cavity QED system at cryogenic temperatures.Also, the system situation can be extended to various quantum emitters at different wavelengths.We discuss such ideas as future prospects.I would like to express my most sincere thanks to Prof. Kohzo Hakuta for his generous support and guidance during my Ph.D. at the Center for Photonic Innovations.I will remain grateful for his motivations, inspirational suggestions, and constructive criticism, teaching me a lot about doing research stringently and presenting the results properly.His deep vision has shaped the thesis into the present form.It was an absolute privilege to learn under his guidance.

•Sep 30, 2020•0 citations

Fluorescence photon measurements from single quantum dots on an optical nanofiber

Ramachandrarao Yalla, K. P. Nayak, K. Hakuta

We experimentally investigate the fluorescence photon emission characteristics for single q-dots by using optical nanofibers. We demonstrate that single q-dots can be deposited along an optical nanofiber systematically and reproducibly with a precision of 5 μm. For single q-dots on an optical nanofiber, we measure the fluorescence photon numbers coupled into the nanofiber and the normalized photon correlations, by varying the excitation laser intensity. We estimate the fluorescence photon coupling efficiency into the nanofiber guided modes.

arXiv:1112.0624•Optics Express•Jan 24, 2012•49 citations

Efficient Channeling of Single Photons into Single Mode Optical Fiber

Ramachandrarao Yalla, Fam Le Kien, M. Morinaga +1 more

We experimentally demonstrate the efficient channeling of fluorescence photons from single q-dots into single-mode optical fiber, by measuring the photon-count rates through the guided and radiation modes simultaneously for various diameters of nanofiber.

Conference on Lasers and Electro-Optics•Jan 1, 2013•0 citations

Study of laser induced fluorescence spectrum of atoms using optical nanofibers

Manoj Das

Fluorescence of atoms has been the subject of interest in quantum optical measurementsfor many years. The atomic fluorescence is routinely used as a tool to detectatoms, to generate photons and to generate non-classical states of light. One of thewidely used methods to investigate the atomic fluorescence is laser-induced fluorescencespectroscopy. This thesis presents the development of optical nanofibers as atool for the measurement of fluorescence spectrum of atoms.Optical nanofibers are ultrathin optical fibers, with diameters less than the propagationwavelength of the fiber, with a silica core and a vacuum clad. Such opticalnanofibers can support only the single propagating guided-mode. The guided-modesof the nanofiber is confined in the transverse direction of the nanofiber and a partof the propagating field lies outside the fiber, in the evanescent region of the fiber.The mode density of the electromagnetic field is modified by the nanofiber. Due tothe modification of mode density, the spontaneous emission of atoms is modified bythe optical nanofibers and the confinement of the guided-modes results in a strongchanneling of spontaneous emission of atoms into the guided-modes of the nanofiber.Such a property of nanofibers can be used to study fluorescence of atoms around thenanofiber.Optical nanofibers are prepared by the adiabatic tapering of single-mode opticalfibers. Our experiments are performed by overlapping cold Cesium atoms, from amagneto-optical trap (MOT), with the optical nanofiber and observing the fluorescencethrough the guided-modes of the nanofiber. The nanofiber suppresses with highprobability any coupling of scattering light from the excitation laser into the guidedmodesand high coupling efficiency of fluorescence into the guided-modes enables us tomeasure the fluorescence spectrum of atoms present around the nanofiber with a goodsignal-to-noise ratio. In this thesis, we demonstrate the measurement of laser inducedfluorescence (LIF) emission spectra of strongly driven atoms using optical nanofibers.For the fluorescence emission spectrum measurements, we develop and demonstrate anew sensitive and high resolution method consisting of optical heterodyne techniqueand photon correlation spectroscopy. The key point of the method is to extract theinformation of first-order field correlation function from the measured second-orderintensity correlation function. The Fourier transform of the field correlation functionthen gives the fluorescence emission spectrum.The atoms emitting fluorescence in the guided-modes of the nanofiber lie very closeto the nanofiber surface and are subjected to atom-surface interactions. It has beenreported in earlier experiments on nanofiber, that such surface interactions can bemodified by irradiating the MOT-atoms overlapped with the nanofiber with UV lasers.After such irradiations, MOT-atoms are kept from falling into the surface-potentialand behave almost like free-space atoms around the nanofiber. We first perform ourfluorescence spectra measurements under this free-atom conditions. The observedexcitation spectrum lineshape shows a free-atom like Lorentzian behavior, with avery small tail in the red-detuned side (red-tail). The red-tail has been attributedto photoassociation process, due to atoms making transition from free ground statesto bound excited states of the surface potential. Under this conditions, the emissionspectra measured for on-resonant and off-resonant excitations show the well-knownthree-peak Mollow-triplet spectrum of free-space two-level atoms. The observationconfirms that the near surface atoms behave like free-space atoms. Also, the quantitativeagreement between the observed spectra with the theoretical calculationsdemonstrates the validity of the optical nanofiber method for measuring fluorescenceemission spectrum of atoms.As mentioned above, since we are observing near-surface atoms, fluorescence measurementsbased on optical nanofibers may become a unique tool to probe atomsurfaceinteractions. In earlier experiments using nanofiber, signatures of atomsurfaceinteraction have been observed in the excitation spectrum of atoms, in theform of a broad red-tail. The lineshape of the excitation spectrum is understood as aresult of a process where atoms approaching the nanofiber surface fall into the shallowsurface potential, forming long-range atom-surface bound states. In this thesis,we have systematically investigated the evolution of the lineshape of the excitationspectrum from a Lorentzian shape to a broad red-tail condition. The evolution of thespectrum lineshape has been attributed to the changing nanofiber surface condition.The spectrum shape is found to depend on the flux of background Cs-atoms. Wespeculate that this might be due to the adsorption of hot background atoms ontothe nanofiber surface, which changes the surface condition of the nanofiber locallyand helps in loading of cold MOT-atoms into the shallow surface potential. We havefound that the effect of UV laser irradiation is to photoionize the MOT-atoms, andthe generated photoelectrons might help in the desorption of adsorbed atoms on thesurface. We discuss the roles of adsorption and desorption of atoms on the surfaceconditions. We have shown that such changing surface condition can be controlledby adjusting the hot background atom flux and the UV laser intensity. Under suchcontrolled surface condition, we have measured the emission spectrum. The observedemission spectrum under the broad red-tail condition can be explained only by includingthe surface interactions. We also discuss qualitatively the phonon-mode densityfor nanofiber at room temperature and the phonon-mediated decay of atoms in thesurface potential.This work may open up the way for using optical nanofibers as a tool to investigatethe laser-induced fluorescence spectrum of strongly driven atoms, and to study atomsurfaceinteractions. In the future, we hope to create optical dipole traps around thenanofibers by introducing trap laser lights through the guided-modes and performfluorescence measurements of these trapped atoms.

•Jan 1, 2011•0 citations

Optical Nanofibers for Manipulating Atoms and Photons

Nayak Kaliprasanna

This thesis presents the development of novel methods for manipulating atomsand photons using an optical nanofiber. Optical nanofibers are vacuum-clad silicafibers with subwavelength-diameter. These optical nanofibers can support only thefundamental mode propagation through the guided mode. The field in the guidedmode is strongly confined in space and a part of the field lies outside the fiber, inthe evanescent region. Such unique property of the field around the optical nanofibermakes it a promising candidate for various quantum optics experiments.Due to the confinement of the field in the guided modes, the spontaneous emissionof atoms can be strongly modified around an optical nanofiber. In this thesis itis experimentally demonstrated that a significant fraction of atomic emission can bechanneled into the guided modes of the nanofiber. Optical nanofibers are realized usingadiabatically tapered single mode optical fibers. Experiments are performed byoverlapping cold Cs-atoms, from a magneto-optical trap (MOT), with the nanofiberand observing fluorescence photons through the guided modes of the nanofiber. Thenanofiber suppresses any scattering light into the guided modes and high coupling efficiencyof fluorescence photons to the guided modes enables us to measure fluorescenceof a very small number of atoms present in the evanescent region of the nanofiber. Sucha technique is further implemented for measuring the density profile and the temperatureof the cold atom cloud.The fluorescence excitation spectrum of cold atoms around an optical nanofiberis investigated by detecting the fluorescence photons through the guided modes. Due tothe inherent nature of the nanofiber method the observed spectrum strongly reflects theeffect of van der Waals (vdW) interaction between atom and nanofiber surface whichwould be dominant for distances closer than /2 from the surface. The observationsare understood through a process where atoms around the nanofiber fall into the vdWpotential forming atom-surface bound states. The observed spectral profiles are wellreproduced from theory considering free-to-bound (photo-association) and bound-toboundtransitions. Furthermore it is demonstrated that the surface conditions can bemodified by irradiating the MOT atoms around the nanofiber using a violet laser radiation.The surface conditions are modified in such a way that the atoms are kept fromfalling into the vdW potential and behave as almost free atoms around the nanofiber.Under such free-atom conditions the photon correlation measurements are performed.The observed antibunching of fluorescence photons demonstrates that singleatoms can be probed efficiently by detecting the fluorescence through the guidedmodes of the nanofiber.The photon correlations are further investigated by varying atom number aroundthe nanofiber. Due to the single spatial mode nature of the nanofiber guided modes, thephoton correlations evolve as interplay between both the first- and second-order coherenceswith increasing atom number. It is shown that both bunching and antibunchingtypes of first-order coherences can contribute to the correlations. However, it is alsoshown that the type of the first-order coherence and its contribution to the correlationscan be strongly affected by the observation and excitation geometries.This work may open up new perspectives for implementing optical nanofibersfor exploring atom-surface interactions, single-atom detection, single photon generationand further applications in the fields of quantum optics and quantum informationtechnologies.

•Jan 1, 2009•0 citations
This thesis presents single photon generation and spectroscopy using quantum dots (q-dots) on optical nanofibers. Optical nanofibers are essentially vacuum-clad silica fibers with sub-wavelength diameter, which can support only the propagation of the fundamental mode through the guided mode. Optical nanofibers are realized using adiabatically tapered single mode optical fibers. Experiments were performed by depositing colloidal core-shell type CdSeTe (ZnS) q-dots on the optical nanofiber surface. A method is developed to deposit single q-dots systematically and reproducibly along the optical nanofiber. In the view point of investigation of fluorescence photon emission characteristics for single q-dots on optical nanofibers, the absolute fluorescence photon-count rates channeled into the nanofiber guided modes and the normalized photon correlations at various excitation laser intensities are measured. The results are able to obtain the product between the fluorescence photon channeling efficiency and the quantum efficiency of the single q-dots. However, the channeling efficiency cannot be determined without accurate information on the quantum efficiency of the single q-dots. Therefore, a method is devised to determine the channeling of fluorescence photons from single q-dots into the guided modes by measuring the fluorescence photon-count rates through the guided and radiation modes simultaneously. By measuring for various nanofiber diameters, a maximum channeling efficiency obtained to be 22.0 (±4.8)% at a fiber diameter of 350 nm for an emission wavelength of 780 nm. The measured results completely reproduce the theoretical predictions within the experimental error. We demonstrate in situ measurements of fluorescence quantum efficiency of single q-dots using the present nanofiber technique. We determine fluorescence quantum efficiency of single q-dots accurately by assuming the theoretical values for the channeling efficiency from the product of the channeling efficiency and the quantum efficiency. We demonstrate that one can pick up one q-dot on the nanofiber with fluorescence quantum efficiency higher than the average value measured for an ensemble. Thus, the optical nanofiber method offers a promising way for generating and manipulating single photons. This work should provide a basis for extending the optical nanofiber method to a general technique in quantum optics, which may open new possibilities in quantum information technologies.
We experimentally demonstrate the efficient channeling of fluorescence photons from single q dots on optical nanofiber into the guided modes by measuring the photon-count rates through the guided and radiation modes simultaneously. We obtain the maximum channeling efficiency to be 22.0(±4.8)% at a fiber diameter of 350 nm for the emission wavelength of 780 nm. The results may open new possibilities in quantum information technologies for generating single photons into single-mode optical fibers.
Hybrid systems of nanophotonic structures and single quantum emitters have emerged as a promising direction for single photon generation in quantum photonic technologies.Strong confinement of the optical field in nanophotonic structures enables photon manipulation far beyond the free space.In this context, tapered optical fibers with sub-wavelength diameter waists, optical nanofibers, provide a unique platform.Regarding the single photon generation, a key advantage is the efficient fiber in-line operation, i.e. photons efficiently emitted into the guided-mode of the nanofiber adiabatically couples to that of a conventional single mode optical fiber with near-unity efficiency.Regarding the emitters for quantum photonics, solid-state emitters at cryogenic temperatures are preferred from the prospect of practical applications in quantum information technologies.In this thesis, a hybrid system of an optical nanofiber (ONF) and a single colloidal CdSe quantum dot (QD) operated at cryogenic temperature is developed and investigated from the viewpoint of fiber in-line single photon generation.Single CdSe core/shell QDs emitting at 640 nm are precisely deposited on the nanofiber surface.An optical cryostat cools the hybrid system to a temperature of 3.7 K via helium buffer-gas cooling, maintaining the high optical transmission of the ONF (94.5%).The photoluminescence (PL) characteristics of the QDs are investigated by observing the emitted photons through the fiber guided-modes.At 3.7 K, the emission spectrum of the single QDs showed two distinct narrow zero-phonon lines (∼350 µeV FWHM) compared to the broad spectral width (60 meV FWHM) at room temperature.viii These lines originate from the neutral and charged states of the QD emitting with near-unity quantum efficiency.The charged QDs are termed as trions.We systematically investigated the emission characteristics of the neutral and the trion states of the QD by spectral, temporal, and photon correlation measurements.The PL decay characteristics of these lines reveal that the upper state of neutral exciton consists of two levels, which effectively results in a fast and slow decay components with decay times of 3.1±0.1 and 153±5 ns, respectively.In contrast, the upper state of trion is one level leading to a single decay process with a decay time of 10.7±0.3 ns.From the viewpoint of single photon generation, the trion with a single upper level is preferable compared to the neutral exciton.Subsequently, a technique to control the occurrence of trion at cryogenic temperatures is developed.It is shown that the trion occurrence can be manipulated by photocharging the QD by exciting well above the band gap.Most notably, we established a method to create permanently charged QDs with all emissions into the trion zero-phonon line.Combining the photocharged single QDs in the hybrid system, we evaluated the performance of the system as an efficient fiber in-line single photon source.We show that the photocharged QDs exhibit a bright photo-stable emission of single photons with near-unity quantum efficiency, narrow spectral width and a fast single decay process.The efficiency of the source is estimated to be 16±2%, with a maximum photon count rate of 1.6±0.2MHz and a high single photon purity of g 2 (0)= 0.11±0.02.The ONF/QD hybrid system could be integrated into the fiber networks paving the way for potential applications in quantum information technologies.The efficiency of the source can be improved by incorporating a cavity structure on the ONF and establish a cavity QED system at cryogenic temperatures.Also, the system situation can be extended to various quantum emitters at different wavelengths.We discuss such ideas as future prospects.I would like to express my most sincere thanks to Prof. Kohzo Hakuta for his generous support and guidance during my Ph.D. at the Center for Photonic Innovations.I will remain grateful for his motivations, inspirational suggestions, and constructive criticism, teaching me a lot about doing research stringently and presenting the results properly.His deep vision has shaped the thesis into the present form.It was an absolute privilege to learn under his guidance.
We experimentally investigate the fluorescence photon emission characteristics for single q-dots by using optical nanofibers. We demonstrate that single q-dots can be deposited along an optical nanofiber systematically and reproducibly with a precision of 5 μm. For single q-dots on an optical nanofiber, we measure the fluorescence photon numbers coupled into the nanofiber and the normalized photon correlations, by varying the excitation laser intensity. We estimate the fluorescence photon coupling efficiency into the nanofiber guided modes.
Fluorescence of atoms has been the subject of interest in quantum optical measurementsfor many years. The atomic fluorescence is routinely used as a tool to detectatoms, to generate photons and to generate non-classical states of light. One of thewidely used methods to investigate the atomic fluorescence is laser-induced fluorescencespectroscopy. This thesis presents the development of optical nanofibers as atool for the measurement of fluorescence spectrum of atoms.Optical nanofibers are ultrathin optical fibers, with diameters less than the propagationwavelength of the fiber, with a silica core and a vacuum clad. Such opticalnanofibers can support only the single propagating guided-mode. The guided-modesof the nanofiber is confined in the transverse direction of the nanofiber and a partof the propagating field lies outside the fiber, in the evanescent region of the fiber.The mode density of the electromagnetic field is modified by the nanofiber. Due tothe modification of mode density, the spontaneous emission of atoms is modified bythe optical nanofibers and the confinement of the guided-modes results in a strongchanneling of spontaneous emission of atoms into the guided-modes of the nanofiber.Such a property of nanofibers can be used to study fluorescence of atoms around thenanofiber.Optical nanofibers are prepared by the adiabatic tapering of single-mode opticalfibers. Our experiments are performed by overlapping cold Cesium atoms, from amagneto-optical trap (MOT), with the optical nanofiber and observing the fluorescencethrough the guided-modes of the nanofiber. The nanofiber suppresses with highprobability any coupling of scattering light from the excitation laser into the guidedmodesand high coupling efficiency of fluorescence into the guided-modes enables us tomeasure the fluorescence spectrum of atoms present around the nanofiber with a goodsignal-to-noise ratio. In this thesis, we demonstrate the measurement of laser inducedfluorescence (LIF) emission spectra of strongly driven atoms using optical nanofibers.For the fluorescence emission spectrum measurements, we develop and demonstrate anew sensitive and high resolution method consisting of optical heterodyne techniqueand photon correlation spectroscopy. The key point of the method is to extract theinformation of first-order field correlation function from the measured second-orderintensity correlation function. The Fourier transform of the field correlation functionthen gives the fluorescence emission spectrum.The atoms emitting fluorescence in the guided-modes of the nanofiber lie very closeto the nanofiber surface and are subjected to atom-surface interactions. It has beenreported in earlier experiments on nanofiber, that such surface interactions can bemodified by irradiating the MOT-atoms overlapped with the nanofiber with UV lasers.After such irradiations, MOT-atoms are kept from falling into the surface-potentialand behave almost like free-space atoms around the nanofiber. We first perform ourfluorescence spectra measurements under this free-atom conditions. The observedexcitation spectrum lineshape shows a free-atom like Lorentzian behavior, with avery small tail in the red-detuned side (red-tail). The red-tail has been attributedto photoassociation process, due to atoms making transition from free ground statesto bound excited states of the surface potential. Under this conditions, the emissionspectra measured for on-resonant and off-resonant excitations show the well-knownthree-peak Mollow-triplet spectrum of free-space two-level atoms. The observationconfirms that the near surface atoms behave like free-space atoms. Also, the quantitativeagreement between the observed spectra with the theoretical calculationsdemonstrates the validity of the optical nanofiber method for measuring fluorescenceemission spectrum of atoms.As mentioned above, since we are observing near-surface atoms, fluorescence measurementsbased on optical nanofibers may become a unique tool to probe atomsurfaceinteractions. In earlier experiments using nanofiber, signatures of atomsurfaceinteraction have been observed in the excitation spectrum of atoms, in theform of a broad red-tail. The lineshape of the excitation spectrum is understood as aresult of a process where atoms approaching the nanofiber surface fall into the shallowsurface potential, forming long-range atom-surface bound states. In this thesis,we have systematically investigated the evolution of the lineshape of the excitationspectrum from a Lorentzian shape to a broad red-tail condition. The evolution of thespectrum lineshape has been attributed to the changing nanofiber surface condition.The spectrum shape is found to depend on the flux of background Cs-atoms. Wespeculate that this might be due to the adsorption of hot background atoms ontothe nanofiber surface, which changes the surface condition of the nanofiber locallyand helps in loading of cold MOT-atoms into the shallow surface potential. We havefound that the effect of UV laser irradiation is to photoionize the MOT-atoms, andthe generated photoelectrons might help in the desorption of adsorbed atoms on thesurface. We discuss the roles of adsorption and desorption of atoms on the surfaceconditions. We have shown that such changing surface condition can be controlledby adjusting the hot background atom flux and the UV laser intensity. Under suchcontrolled surface condition, we have measured the emission spectrum. The observedemission spectrum under the broad red-tail condition can be explained only by includingthe surface interactions. We also discuss qualitatively the phonon-mode densityfor nanofiber at room temperature and the phonon-mediated decay of atoms in thesurface potential.This work may open up the way for using optical nanofibers as a tool to investigatethe laser-induced fluorescence spectrum of strongly driven atoms, and to study atomsurfaceinteractions. In the future, we hope to create optical dipole traps around thenanofibers by introducing trap laser lights through the guided-modes and performfluorescence measurements of these trapped atoms.
This thesis presents the development of novel methods for manipulating atomsand photons using an optical nanofiber. Optical nanofibers are vacuum-clad silicafibers with subwavelength-diameter. These optical nanofibers can support only thefundamental mode propagation through the guided mode. The field in the guidedmode is strongly confined in space and a part of the field lies outside the fiber, inthe evanescent region. Such unique property of the field around the optical nanofibermakes it a promising candidate for various quantum optics experiments.Due to the confinement of the field in the guided modes, the spontaneous emissionof atoms can be strongly modified around an optical nanofiber. In this thesis itis experimentally demonstrated that a significant fraction of atomic emission can bechanneled into the guided modes of the nanofiber. Optical nanofibers are realized usingadiabatically tapered single mode optical fibers. Experiments are performed byoverlapping cold Cs-atoms, from a magneto-optical trap (MOT), with the nanofiberand observing fluorescence photons through the guided modes of the nanofiber. Thenanofiber suppresses any scattering light into the guided modes and high coupling efficiencyof fluorescence photons to the guided modes enables us to measure fluorescenceof a very small number of atoms present in the evanescent region of the nanofiber. Sucha technique is further implemented for measuring the density profile and the temperatureof the cold atom cloud.The fluorescence excitation spectrum of cold atoms around an optical nanofiberis investigated by detecting the fluorescence photons through the guided modes. Due tothe inherent nature of the nanofiber method the observed spectrum strongly reflects theeffect of van der Waals (vdW) interaction between atom and nanofiber surface whichwould be dominant for distances closer than /2 from the surface. The observationsare understood through a process where atoms around the nanofiber fall into the vdWpotential forming atom-surface bound states. The observed spectral profiles are wellreproduced from theory considering free-to-bound (photo-association) and bound-toboundtransitions. Furthermore it is demonstrated that the surface conditions can bemodified by irradiating the MOT atoms around the nanofiber using a violet laser radiation.The surface conditions are modified in such a way that the atoms are kept fromfalling into the vdW potential and behave as almost free atoms around the nanofiber.Under such free-atom conditions the photon correlation measurements are performed.The observed antibunching of fluorescence photons demonstrates that singleatoms can be probed efficiently by detecting the fluorescence through the guidedmodes of the nanofiber.The photon correlations are further investigated by varying atom number aroundthe nanofiber. Due to the single spatial mode nature of the nanofiber guided modes, thephoton correlations evolve as interplay between both the first- and second-order coherenceswith increasing atom number. It is shown that both bunching and antibunchingtypes of first-order coherences can contribute to the correlations. However, it is alsoshown that the type of the first-order coherence and its contribution to the correlationscan be strongly affected by the observation and excitation geometries.This work may open up new perspectives for implementing optical nanofibersfor exploring atom-surface interactions, single-atom detection, single photon generationand further applications in the fields of quantum optics and quantum informationtechnologies.