Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1204.6153 · Physical Review Letters

Efficient Channeling of Fluorescence Photons from Single Quantum Dots into Guided Modes of Optical Nanofiber

Ramachandrarao Yalla, Fam Le Kien, M. Morinaga, K. Hakuta

Published Aug 8, 2012• 187 citations
arXivHTMLPDF

Abstract

We experimentally demonstrate the efficient channeling of fluorescence photons from single q dots on optical nanofiber into the guided modes by measuring the photon-count rates through the guided and radiation modes simultaneously. We obtain the maximum channeling efficiency to be 22.0(±4.8)% at a fiber diameter of 350 nm for the emission wavelength of 780 nm. The results may open new possibilities in quantum information technologies for generating single photons into single-mode optical fibers.

DOI
10.1103/physrevlett.109.063602

Related papers

Single Photon Generation and Spectroscopy Using Quantum Dots on Optical Nanofibers

Ramachandrarao Yalla

This thesis presents single photon generation and spectroscopy using quantum dots (q-dots) on optical nanofibers. Optical nanofibers are essentially vacuum-clad silica fibers with sub-wavelength diameter, which can support only the propagation of the fundamental mode through the guided mode. Optical nanofibers are realized using adiabatically tapered single mode optical fibers. Experiments were performed by depositing colloidal core-shell type CdSeTe (ZnS) q-dots on the optical nanofiber surface. A method is developed to deposit single q-dots systematically and reproducibly along the optical nanofiber. In the view point of investigation of fluorescence photon emission characteristics for single q-dots on optical nanofibers, the absolute fluorescence photon-count rates channeled into the nanofiber guided modes and the normalized photon correlations at various excitation laser intensities are measured. The results are able to obtain the product between the fluorescence photon channeling efficiency and the quantum efficiency of the single q-dots. However, the channeling efficiency cannot be determined without accurate information on the quantum efficiency of the single q-dots. Therefore, a method is devised to determine the channeling of fluorescence photons from single q-dots into the guided modes by measuring the fluorescence photon-count rates through the guided and radiation modes simultaneously. By measuring for various nanofiber diameters, a maximum channeling efficiency obtained to be 22.0 (±4.8)% at a fiber diameter of 350 nm for an emission wavelength of 780 nm. The measured results completely reproduce the theoretical predictions within the experimental error. We demonstrate in situ measurements of fluorescence quantum efficiency of single q-dots using the present nanofiber technique. We determine fluorescence quantum efficiency of single q-dots accurately by assuming the theoretical values for the channeling efficiency from the product of the channeling efficiency and the quantum efficiency. We demonstrate that one can pick up one q-dot on the nanofiber with fluorescence quantum efficiency higher than the average value measured for an ensemble. Thus, the optical nanofiber method offers a promising way for generating and manipulating single photons. This work should provide a basis for extending the optical nanofiber method to a general technique in quantum optics, which may open new possibilities in quantum information technologies.

•Jan 1, 2012•1 citation

Efficient Channeling of Single Photons into Single Mode Optical Fiber

Ramachandrarao Yalla, Fam Le Kien, M. Morinaga +1 more

We experimentally demonstrate the efficient channeling of fluorescence photons from single q-dots into single-mode optical fiber, by measuring the photon-count rates through the guided and radiation modes simultaneously for various diameters of nanofiber.

Conference on Lasers and Electro-Optics•Jan 1, 2013•0 citations

Manipulating single atoms and photons using optical nanofibers

K. Hakuta, K. P. Nayak

Abstract We discuss how optical nanofibers, subwavelength-diameter fibers, can open new perspectives in quantum optical technologies theoretically and experimentally. Discussions are mainly focused on the manipulation of spontaneous emission for atoms around the nanofiber. We show that photons from single quantum emitters can be efficiently channeled into guided modes of the nanofiber. Especially by fabricating a cavity structure of the nanofiber, the channeling efficiency can be improved to exceed 80% although the cavity finesse is moderate. We discuss also how to realize such a nanofiber cavity experimentally.

Advances in Natural Sciences Nanoscience and Nanotechnology•Feb 21, 2012•11 citations

Fluorescence photon measurements from single quantum dots on an optical nanofiber

Ramachandrarao Yalla, K. P. Nayak, K. Hakuta

We experimentally investigate the fluorescence photon emission characteristics for single q-dots by using optical nanofibers. We demonstrate that single q-dots can be deposited along an optical nanofiber systematically and reproducibly with a precision of 5 μm. For single q-dots on an optical nanofiber, we measure the fluorescence photon numbers coupled into the nanofiber and the normalized photon correlations, by varying the excitation laser intensity. We estimate the fluorescence photon coupling efficiency into the nanofiber guided modes.

arXiv:1112.0624•Optics Express•Jan 24, 2012•49 citations

Bright and Polarized Fiber In-Line Single-Photon Source Based on Plasmon-Enhanced Emission into Nanofiber Guided Modes

K. Muhammed Shafi, Ramachandrarao Yalla, K. P. Nayak

We demonstrate a bright and polarized fiber in-line single-photon source based on plasmon-enhanced emission of colloidal single quantum dots into an optical nanofiber. We show that emission properties of single quantum dots can be strongly enhanced in the presence of single gold nanorods leading to a bright and strongly polarized single-photon emission. The single photons are efficiently coupled to guided modes of the nanofiber and eventually to a single-mode optical fiber. The brightness (fiber-coupled photon count rate) of the single-photon source is estimated to be $12.2\ifmmode\pm\else\textpm\fi{}0.6$ MHz, with high single-photon purity [${g}^{2}(0)=0.20\ifmmode\pm\else\textpm\fi{}0.04$] and degree of polarization as high as 94--97 %. The polarized and fiber-coupled single photons can be implemented for potential applications in quantum photonics.

arXiv:2206.13029•Physical Review Applied•Mar 2, 2023•21 citations

Hybrid System of Optical Nanofiber and Single Quantum Dot for Fiber In-Line Single Photon Generation

Muhammed Shafi Kodakkaden

Hybrid systems of nanophotonic structures and single quantum emitters have emerged as a promising direction for single photon generation in quantum photonic technologies.Strong confinement of the optical field in nanophotonic structures enables photon manipulation far beyond the free space.In this context, tapered optical fibers with sub-wavelength diameter waists, optical nanofibers, provide a unique platform.Regarding the single photon generation, a key advantage is the efficient fiber in-line operation, i.e. photons efficiently emitted into the guided-mode of the nanofiber adiabatically couples to that of a conventional single mode optical fiber with near-unity efficiency.Regarding the emitters for quantum photonics, solid-state emitters at cryogenic temperatures are preferred from the prospect of practical applications in quantum information technologies.In this thesis, a hybrid system of an optical nanofiber (ONF) and a single colloidal CdSe quantum dot (QD) operated at cryogenic temperature is developed and investigated from the viewpoint of fiber in-line single photon generation.Single CdSe core/shell QDs emitting at 640 nm are precisely deposited on the nanofiber surface.An optical cryostat cools the hybrid system to a temperature of 3.7 K via helium buffer-gas cooling, maintaining the high optical transmission of the ONF (94.5%).The photoluminescence (PL) characteristics of the QDs are investigated by observing the emitted photons through the fiber guided-modes.At 3.7 K, the emission spectrum of the single QDs showed two distinct narrow zero-phonon lines (∼350 µeV FWHM) compared to the broad spectral width (60 meV FWHM) at room temperature.viii These lines originate from the neutral and charged states of the QD emitting with near-unity quantum efficiency.The charged QDs are termed as trions.We systematically investigated the emission characteristics of the neutral and the trion states of the QD by spectral, temporal, and photon correlation measurements.The PL decay characteristics of these lines reveal that the upper state of neutral exciton consists of two levels, which effectively results in a fast and slow decay components with decay times of 3.1±0.1 and 153±5 ns, respectively.In contrast, the upper state of trion is one level leading to a single decay process with a decay time of 10.7±0.3 ns.From the viewpoint of single photon generation, the trion with a single upper level is preferable compared to the neutral exciton.Subsequently, a technique to control the occurrence of trion at cryogenic temperatures is developed.It is shown that the trion occurrence can be manipulated by photocharging the QD by exciting well above the band gap.Most notably, we established a method to create permanently charged QDs with all emissions into the trion zero-phonon line.Combining the photocharged single QDs in the hybrid system, we evaluated the performance of the system as an efficient fiber in-line single photon source.We show that the photocharged QDs exhibit a bright photo-stable emission of single photons with near-unity quantum efficiency, narrow spectral width and a fast single decay process.The efficiency of the source is estimated to be 16±2%, with a maximum photon count rate of 1.6±0.2MHz and a high single photon purity of g 2 (0)= 0.11±0.02.The ONF/QD hybrid system could be integrated into the fiber networks paving the way for potential applications in quantum information technologies.The efficiency of the source can be improved by incorporating a cavity structure on the ONF and establish a cavity QED system at cryogenic temperatures.Also, the system situation can be extended to various quantum emitters at different wavelengths.We discuss such ideas as future prospects.I would like to express my most sincere thanks to Prof. Kohzo Hakuta for his generous support and guidance during my Ph.D. at the Center for Photonic Innovations.I will remain grateful for his motivations, inspirational suggestions, and constructive criticism, teaching me a lot about doing research stringently and presenting the results properly.His deep vision has shaped the thesis into the present form.It was an absolute privilege to learn under his guidance.

•Sep 30, 2020•0 citations
We experimentally demonstrate the efficient channeling of fluorescence photons from single q dots on optical nanofiber into the guided modes by measuring the photon-count rates through the guided and radiation modes simultaneously. We obtain the maximum channeling efficiency to be 22.0(±4.8)% at a fiber diameter of 350 nm for the emission wavelength of 780 nm. The results may open new possibilities in quantum information technologies for generating single photons into single-mode optical fibers.
This thesis presents single photon generation and spectroscopy using quantum dots (q-dots) on optical nanofibers. Optical nanofibers are essentially vacuum-clad silica fibers with sub-wavelength diameter, which can support only the propagation of the fundamental mode through the guided mode. Optical nanofibers are realized using adiabatically tapered single mode optical fibers. Experiments were performed by depositing colloidal core-shell type CdSeTe (ZnS) q-dots on the optical nanofiber surface. A method is developed to deposit single q-dots systematically and reproducibly along the optical nanofiber. In the view point of investigation of fluorescence photon emission characteristics for single q-dots on optical nanofibers, the absolute fluorescence photon-count rates channeled into the nanofiber guided modes and the normalized photon correlations at various excitation laser intensities are measured. The results are able to obtain the product between the fluorescence photon channeling efficiency and the quantum efficiency of the single q-dots. However, the channeling efficiency cannot be determined without accurate information on the quantum efficiency of the single q-dots. Therefore, a method is devised to determine the channeling of fluorescence photons from single q-dots into the guided modes by measuring the fluorescence photon-count rates through the guided and radiation modes simultaneously. By measuring for various nanofiber diameters, a maximum channeling efficiency obtained to be 22.0 (±4.8)% at a fiber diameter of 350 nm for an emission wavelength of 780 nm. The measured results completely reproduce the theoretical predictions within the experimental error. We demonstrate in situ measurements of fluorescence quantum efficiency of single q-dots using the present nanofiber technique. We determine fluorescence quantum efficiency of single q-dots accurately by assuming the theoretical values for the channeling efficiency from the product of the channeling efficiency and the quantum efficiency. We demonstrate that one can pick up one q-dot on the nanofiber with fluorescence quantum efficiency higher than the average value measured for an ensemble. Thus, the optical nanofiber method offers a promising way for generating and manipulating single photons. This work should provide a basis for extending the optical nanofiber method to a general technique in quantum optics, which may open new possibilities in quantum information technologies.
Abstract We discuss how optical nanofibers, subwavelength-diameter fibers, can open new perspectives in quantum optical technologies theoretically and experimentally. Discussions are mainly focused on the manipulation of spontaneous emission for atoms around the nanofiber. We show that photons from single quantum emitters can be efficiently channeled into guided modes of the nanofiber. Especially by fabricating a cavity structure of the nanofiber, the channeling efficiency can be improved to exceed 80% although the cavity finesse is moderate. We discuss also how to realize such a nanofiber cavity experimentally.
We experimentally investigate the fluorescence photon emission characteristics for single q-dots by using optical nanofibers. We demonstrate that single q-dots can be deposited along an optical nanofiber systematically and reproducibly with a precision of 5 μm. For single q-dots on an optical nanofiber, we measure the fluorescence photon numbers coupled into the nanofiber and the normalized photon correlations, by varying the excitation laser intensity. We estimate the fluorescence photon coupling efficiency into the nanofiber guided modes.
We demonstrate a bright and polarized fiber in-line single-photon source based on plasmon-enhanced emission of colloidal single quantum dots into an optical nanofiber. We show that emission properties of single quantum dots can be strongly enhanced in the presence of single gold nanorods leading to a bright and strongly polarized single-photon emission. The single photons are efficiently coupled to guided modes of the nanofiber and eventually to a single-mode optical fiber. The brightness (fiber-coupled photon count rate) of the single-photon source is estimated to be $12.2\ifmmode\pm\else\textpm\fi{}0.6$ MHz, with high single-photon purity [${g}^{2}(0)=0.20\ifmmode\pm\else\textpm\fi{}0.04$] and degree of polarization as high as 94--97 %. The polarized and fiber-coupled single photons can be implemented for potential applications in quantum photonics.
Hybrid systems of nanophotonic structures and single quantum emitters have emerged as a promising direction for single photon generation in quantum photonic technologies.Strong confinement of the optical field in nanophotonic structures enables photon manipulation far beyond the free space.In this context, tapered optical fibers with sub-wavelength diameter waists, optical nanofibers, provide a unique platform.Regarding the single photon generation, a key advantage is the efficient fiber in-line operation, i.e. photons efficiently emitted into the guided-mode of the nanofiber adiabatically couples to that of a conventional single mode optical fiber with near-unity efficiency.Regarding the emitters for quantum photonics, solid-state emitters at cryogenic temperatures are preferred from the prospect of practical applications in quantum information technologies.In this thesis, a hybrid system of an optical nanofiber (ONF) and a single colloidal CdSe quantum dot (QD) operated at cryogenic temperature is developed and investigated from the viewpoint of fiber in-line single photon generation.Single CdSe core/shell QDs emitting at 640 nm are precisely deposited on the nanofiber surface.An optical cryostat cools the hybrid system to a temperature of 3.7 K via helium buffer-gas cooling, maintaining the high optical transmission of the ONF (94.5%).The photoluminescence (PL) characteristics of the QDs are investigated by observing the emitted photons through the fiber guided-modes.At 3.7 K, the emission spectrum of the single QDs showed two distinct narrow zero-phonon lines (∼350 µeV FWHM) compared to the broad spectral width (60 meV FWHM) at room temperature.viii These lines originate from the neutral and charged states of the QD emitting with near-unity quantum efficiency.The charged QDs are termed as trions.We systematically investigated the emission characteristics of the neutral and the trion states of the QD by spectral, temporal, and photon correlation measurements.The PL decay characteristics of these lines reveal that the upper state of neutral exciton consists of two levels, which effectively results in a fast and slow decay components with decay times of 3.1±0.1 and 153±5 ns, respectively.In contrast, the upper state of trion is one level leading to a single decay process with a decay time of 10.7±0.3 ns.From the viewpoint of single photon generation, the trion with a single upper level is preferable compared to the neutral exciton.Subsequently, a technique to control the occurrence of trion at cryogenic temperatures is developed.It is shown that the trion occurrence can be manipulated by photocharging the QD by exciting well above the band gap.Most notably, we established a method to create permanently charged QDs with all emissions into the trion zero-phonon line.Combining the photocharged single QDs in the hybrid system, we evaluated the performance of the system as an efficient fiber in-line single photon source.We show that the photocharged QDs exhibit a bright photo-stable emission of single photons with near-unity quantum efficiency, narrow spectral width and a fast single decay process.The efficiency of the source is estimated to be 16±2%, with a maximum photon count rate of 1.6±0.2MHz and a high single photon purity of g 2 (0)= 0.11±0.02.The ONF/QD hybrid system could be integrated into the fiber networks paving the way for potential applications in quantum information technologies.The efficiency of the source can be improved by incorporating a cavity structure on the ONF and establish a cavity QED system at cryogenic temperatures.Also, the system situation can be extended to various quantum emitters at different wavelengths.We discuss such ideas as future prospects.I would like to express my most sincere thanks to Prof. Kohzo Hakuta for his generous support and guidance during my Ph.D. at the Center for Photonic Innovations.I will remain grateful for his motivations, inspirational suggestions, and constructive criticism, teaching me a lot about doing research stringently and presenting the results properly.His deep vision has shaped the thesis into the present form.It was an absolute privilege to learn under his guidance.