Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

3.69 GHz single flux quantum pseudorandom bit sequence generator fabricated with Nb/AlO/sub x//Nb

J.H. Kang, John X. Przybysz, S.S. Martinet, A. Hodge Worsham, Donald L. Miller, James D. McCambridge

Published Jun 1, 1997• 15 citations
Publisher

Abstract

A 4 bit 15 sequence SFQ (Single Flux Quantum) pseudorandom bit sequence generator was built with an eight-level Nb/AlO/sub x//Nb Josephson junction integrated circuit process. An SFQ circuit was built into the code generator to enable a rapid restart. The test results showed that the circuit operated correctly at the seed of 3.69 GHz. The XNOR gate and shift register worked correctly at 5 GHz. However, the back delay was longer than 200 psec and the generator acted as a 5 bit 21 sequence code generator at this frequency. At 200 MHz, the code generator was operated continuously to observe its stability. Over the course of two and one half hours, the circuit made only five code errors, indicating a bit error rate of 3/spl times/10/sup -12/. At 2 GHz we collected 10 million samples on the 4023rd bit of the sequence. No wrong signal values were observed, indicating the bit error rate is less than 5/spl times/10/sup -11/ at this frequency.

DOI
10.1109/77.621789

Related papers

4.6 GHz SFQ shift register and SFQ pseudorandom bit sequence generator

Joonhee Kang, A. Hodge Worsham, John X. Przybysz

Superconductive electronics can provide low power, GHz speed spread spectrum satellite communications. The key components to construct the spread spectrum modem are an analog filter and a digital pseudorandom bit sequence generator, Various SFQ logic circuits are required to construct a code generator. These circuits include a shift register, a reset switch, and an XOR or XNOR. To make a 4 bit 15 sequence code generator, a four stage shift register with a fan-out of two on each stage was designed. These circuits, fabricated with eight level Nb/AlO/sub x//Nb Josephson junction integrated circuit process, showed correct operation at low speed digital tests. The low speed digital test was done by using a "catcher", the combination of a read SQUID and a Josephson transmission line (JTL) which were magnetically coupled to each other. High speed testing of the shift register used a latch amplifier, which amplified an SFQ pulse to a latching output voltage of about 2 mV. This test showed correct operation of the shift register at speeds of up to 4.6 GHz.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•23 citations

Three Parallel Generation of a 4-bit M-Sequence Using Single-Flux-Quantum Digital Circuits

Yoshinao Mizugaki, Yasuaki Mutoh, Yoshiaki Urai +2 more

Maximum-length sequences (M-sequences) are known as pseudo-random numbers generated with relatively simple digital circuits. In this paper, we present a single-flux-quantum digital circuit that generated three output bits of a 4-bit M-sequence in one clock operation. The circuit comprised three clocked exclusive-or gates, one delay flip-flop, three dc/SFQ converters (for set, reset, and low-frequency clock signals), and three SFQ/dc converters (for three parallel outputs), all of which were integrated on a superconducting Nb chip. A 10-GHz clock generator was also implemented for high-speed testing. The total number of Nb/AlOx/Nb Josephson junctions was 568. Verilog simulation demonstrated correct circuit operation with a 20-GHz clock, which corresponded to the generation rate of 60 Gb/s. The measurement was carried out in a liquid helium bath. Low-speed testing with a 1-kHz clock demonstrated periodic signals of three parallelized 4-bit M-sequence. We also confirmed that the outputs were correctly shifted when 13 clock signals of 10 GHz were fed between two 1-kHz clock signals.

IEEE Transactions on Applied Superconductivity•Mar 1, 2016•3 citations

Three Parallel Generation of a 4-Bit M-Sequence Using Single-Flux-Quantum Digital Circuits

Yoshinao Mizugaki, Yasuaki Mutoh, Yoshiaki Urai +2 more

Maximum-length sequences (M-sequences) are known as pseudo random numbers generated with relatively simple digital circuits. In this paper, we present a 4-bit M-sequence generator designed and fabricated using a single-flux-quantum (SFQ) logic library and a niobium integration technology. To enhance its generation rate, we have introduced a parallelization scheme where three bits are simultaneously generated in one clock operation. The circuit comprises three exclusive ORs, one delay flip-flop, two dc/SFQ converters (for SET and CLOCK signals), and three SFQ/dc converters (for three parallel outputs). A 10-GHz clock generator of 13 bits is also implemented for high speed testing. The total number of Nb/AlOx/Nb Josephson junctions is 568. Verilog simulation has demonstrated correct circuit operation at 20-GHz clock, which corresponds to the generation rate of 60 Gb/s. The measurement was carried out in a liquid helium bath with double μ-metal cans. Low speed testing with a 1-kHz clock demonstrated periodic signals of three parallelized 4-bit M-sequence; (0, 1, 0), (1, 1, 1), (1, 0, 0), (0, 1, 0), and (0, 1, 1), where (out1, out2, out3) represents the signals from the output ports. We also confirmed that the output signals were correctly shifted when 10-GHz clocks of 13 bits were fed between two 1-kHz clock signals.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2015•1 citation

Performance issues in single flux quantum shift registers

J.H. Hang, John X. Przybysz

Testing on a single-flux-quantum (SFQ) shift register fabricated with a SFQ Nb-AlO/sub x/Nb Josephson junction process indicates that a stable flux quantum can be stored in a rapid SFQ (RSFQ) shift register stage and be shifted by SFQ pulses. Design simulations showed that logic errors can occur in SFQ shift registers even though the circuit passes the average voltage test. Three-junction-per-stage shift registers had an advantage over the two-junction-per-stage shift register in handling data with successive 1's and in incorporating resistors to increase tolerance of trapped magnetic flux. Input and output buffers for data and clock pulses were added to get an RSFQ shift register to obtain correct performance. The highest error-free operation speed for the data with successive 1's is about half of the speed for propagation of a lone data 1. Error-free operation of SFQ shift registers with three junctions per stage could be obtained up to speeds of 30-60 GHz with Josephson junctions having I/sub c/R/sub n/ (critical-current-normal-resistance product) values of 600 mu V.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•8 citations

Design and testing of rapid single flux quantum shift registers with magnetically coupled readout gates

Perng-Fei Yuh, Oleg A. Mukhanov

Experimental superconducting shift registers consisting of on-chip clock generators, clock regeneration and distribution circuits, shift register elements, and readout circuits are designed using rapid single flux quantum logic/memory (RSFQ) gates. A 7-b shift register has been tested to 12 GHz and a 17-b to 21 GHz using external triggering clocks with relative delay measurements. Testing with internal clocks generated from Josephson oscillations shows a potential high-speed operation of 45 GHz for the 7-b and 30 GHz for the 17-b shift registers. Two types of magnetically coupled readout gates are discussed. The chips are fabricated using a Nb/AlO/sub /x/Nb Josephson-junction process at a critical-current density of 1000 A/cm/sup 2/. The power dissipation per bit is 3 mu W.>

IEEE Transactions on Applied Superconductivity•Jan 1, 1992•20 citations

Bit error rate measurements for GHz code generator circuits

E.J. Dean, P.D. Dresseihaus, John X. Przybysz +3 more

A new method of analyzing bit error rates (BERs) for SFQ circuits and their outputs at GHz speeds will be presented. This method was used to test four- and six-bit pseudorandom code generators. The code generators were operated in free-run mode, i.e., without a synchronization (Reset) pulse. This enabled us to conduct BER testing to much lower levels than when the code generator is operated in Reset mode. The SFQ circuit output was amplified with a superconducting output latch to give voltage levels suitable for display on a sampling scope. The GHz output data was analyzed by external computer software; this permitted extended tests without user supervision. With the code generators operating in free-run mode, they routinely gave bit error rates (BERs) in the 10/sup -11/ range; the best BER recorded was 1.1*10/sup -13/ (2 errors in /spl sim/2.5 hours) at 2 GHz. We have successfully tested these code generators at frequencies in excess of 3.5 GHz with BERs in the 10/sup -10/ range as well.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•3 citations
A 4 bit 15 sequence SFQ (Single Flux Quantum) pseudorandom bit sequence generator was built with an eight-level Nb/AlO/sub x//Nb Josephson junction integrated circuit process. An SFQ circuit was built into the code generator to enable a rapid restart. The test results showed that the circuit operated correctly at the seed of 3.69 GHz. The XNOR gate and shift register worked correctly at 5 GHz. However, the back delay was longer than 200 psec and the generator acted as a 5 bit 21 sequence code generator at this frequency. At 200 MHz, the code generator was operated continuously to observe its stability. Over the course of two and one half hours, the circuit made only five code errors, indicating a bit error rate of 3/spl times/10/sup -12/. At 2 GHz we collected 10 million samples on the 4023rd bit of the sequence. No wrong signal values were observed, indicating the bit error rate is less than 5/spl times/10/sup -11/ at this frequency.
Superconductive electronics can provide low power, GHz speed spread spectrum satellite communications. The key components to construct the spread spectrum modem are an analog filter and a digital pseudorandom bit sequence generator, Various SFQ logic circuits are required to construct a code generator. These circuits include a shift register, a reset switch, and an XOR or XNOR. To make a 4 bit 15 sequence code generator, a four stage shift register with a fan-out of two on each stage was designed. These circuits, fabricated with eight level Nb/AlO/sub x//Nb Josephson junction integrated circuit process, showed correct operation at low speed digital tests. The low speed digital test was done by using a "catcher", the combination of a read SQUID and a Josephson transmission line (JTL) which were magnetically coupled to each other. High speed testing of the shift register used a latch amplifier, which amplified an SFQ pulse to a latching output voltage of about 2 mV. This test showed correct operation of the shift register at speeds of up to 4.6 GHz.>
Maximum-length sequences (M-sequences) are known as pseudo-random numbers generated with relatively simple digital circuits. In this paper, we present a single-flux-quantum digital circuit that generated three output bits of a 4-bit M-sequence in one clock operation. The circuit comprised three clocked exclusive-or gates, one delay flip-flop, three dc/SFQ converters (for set, reset, and low-frequency clock signals), and three SFQ/dc converters (for three parallel outputs), all of which were integrated on a superconducting Nb chip. A 10-GHz clock generator was also implemented for high-speed testing. The total number of Nb/AlOx/Nb Josephson junctions was 568. Verilog simulation demonstrated correct circuit operation with a 20-GHz clock, which corresponded to the generation rate of 60 Gb/s. The measurement was carried out in a liquid helium bath. Low-speed testing with a 1-kHz clock demonstrated periodic signals of three parallelized 4-bit M-sequence. We also confirmed that the outputs were correctly shifted when 13 clock signals of 10 GHz were fed between two 1-kHz clock signals.
Maximum-length sequences (M-sequences) are known as pseudo random numbers generated with relatively simple digital circuits. In this paper, we present a 4-bit M-sequence generator designed and fabricated using a single-flux-quantum (SFQ) logic library and a niobium integration technology. To enhance its generation rate, we have introduced a parallelization scheme where three bits are simultaneously generated in one clock operation. The circuit comprises three exclusive ORs, one delay flip-flop, two dc/SFQ converters (for SET and CLOCK signals), and three SFQ/dc converters (for three parallel outputs). A 10-GHz clock generator of 13 bits is also implemented for high speed testing. The total number of Nb/AlOx/Nb Josephson junctions is 568. Verilog simulation has demonstrated correct circuit operation at 20-GHz clock, which corresponds to the generation rate of 60 Gb/s. The measurement was carried out in a liquid helium bath with double μ-metal cans. Low speed testing with a 1-kHz clock demonstrated periodic signals of three parallelized 4-bit M-sequence; (0, 1, 0), (1, 1, 1), (1, 0, 0), (0, 1, 0), and (0, 1, 1), where (out1, out2, out3) represents the signals from the output ports. We also confirmed that the output signals were correctly shifted when 10-GHz clocks of 13 bits were fed between two 1-kHz clock signals.
Testing on a single-flux-quantum (SFQ) shift register fabricated with a SFQ Nb-AlO/sub x/Nb Josephson junction process indicates that a stable flux quantum can be stored in a rapid SFQ (RSFQ) shift register stage and be shifted by SFQ pulses. Design simulations showed that logic errors can occur in SFQ shift registers even though the circuit passes the average voltage test. Three-junction-per-stage shift registers had an advantage over the two-junction-per-stage shift register in handling data with successive 1's and in incorporating resistors to increase tolerance of trapped magnetic flux. Input and output buffers for data and clock pulses were added to get an RSFQ shift register to obtain correct performance. The highest error-free operation speed for the data with successive 1's is about half of the speed for propagation of a lone data 1. Error-free operation of SFQ shift registers with three junctions per stage could be obtained up to speeds of 30-60 GHz with Josephson junctions having I/sub c/R/sub n/ (critical-current-normal-resistance product) values of 600 mu V.>
Experimental superconducting shift registers consisting of on-chip clock generators, clock regeneration and distribution circuits, shift register elements, and readout circuits are designed using rapid single flux quantum logic/memory (RSFQ) gates. A 7-b shift register has been tested to 12 GHz and a 17-b to 21 GHz using external triggering clocks with relative delay measurements. Testing with internal clocks generated from Josephson oscillations shows a potential high-speed operation of 45 GHz for the 7-b and 30 GHz for the 17-b shift registers. Two types of magnetically coupled readout gates are discussed. The chips are fabricated using a Nb/AlO/sub /x/Nb Josephson-junction process at a critical-current density of 1000 A/cm/sup 2/. The power dissipation per bit is 3 mu W.>
A new method of analyzing bit error rates (BERs) for SFQ circuits and their outputs at GHz speeds will be presented. This method was used to test four- and six-bit pseudorandom code generators. The code generators were operated in free-run mode, i.e., without a synchronization (Reset) pulse. This enabled us to conduct BER testing to much lower levels than when the code generator is operated in Reset mode. The SFQ circuit output was amplified with a superconducting output latch to give voltage levels suitable for display on a sampling scope. The GHz output data was analyzed by external computer software; this permitted extended tests without user supervision. With the code generators operating in free-run mode, they routinely gave bit error rates (BERs) in the 10/sup -11/ range; the best BER recorded was 1.1*10/sup -13/ (2 errors in /spl sim/2.5 hours) at 2 GHz. We have successfully tested these code generators at frequencies in excess of 3.5 GHz with BERs in the 10/sup -10/ range as well.