Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Bit error rate measurements for GHz code generator circuits

E.J. Dean, P.D. Dresseihaus, John X. Przybysz, A. H. Miklich, A. Hodge Worsham, Stanislav V. Polonsky

Published Jun 1, 1999• 3 citations
Publisher

Abstract

A new method of analyzing bit error rates (BERs) for SFQ circuits and their outputs at GHz speeds will be presented. This method was used to test four- and six-bit pseudorandom code generators. The code generators were operated in free-run mode, i.e., without a synchronization (Reset) pulse. This enabled us to conduct BER testing to much lower levels than when the code generator is operated in Reset mode. The SFQ circuit output was amplified with a superconducting output latch to give voltage levels suitable for display on a sampling scope. The GHz output data was analyzed by external computer software; this permitted extended tests without user supervision. With the code generators operating in free-run mode, they routinely gave bit error rates (BERs) in the 10/sup -11/ range; the best BER recorded was 1.1*10/sup -13/ (2 errors in /spl sim/2.5 hours) at 2 GHz. We have successfully tested these code generators at frequencies in excess of 3.5 GHz with BERs in the 10/sup -10/ range as well.

DOI
10.1109/77.783808

Related papers

3.69 GHz single flux quantum pseudorandom bit sequence generator fabricated with Nb/AlO/sub x//Nb

J.H. Kang, John X. Przybysz, S.S. Martinet +3 more

A 4 bit 15 sequence SFQ (Single Flux Quantum) pseudorandom bit sequence generator was built with an eight-level Nb/AlO/sub x//Nb Josephson junction integrated circuit process. An SFQ circuit was built into the code generator to enable a rapid restart. The test results showed that the circuit operated correctly at the seed of 3.69 GHz. The XNOR gate and shift register worked correctly at 5 GHz. However, the back delay was longer than 200 psec and the generator acted as a 5 bit 21 sequence code generator at this frequency. At 200 MHz, the code generator was operated continuously to observe its stability. Over the course of two and one half hours, the circuit made only five code errors, indicating a bit error rate of 3/spl times/10/sup -12/. At 2 GHz we collected 10 million samples on the 4023rd bit of the sequence. No wrong signal values were observed, indicating the bit error rate is less than 5/spl times/10/sup -11/ at this frequency.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•15 citations

Counting SFQ analog to digital converter results

Robert D. Sandell, D.J. Durand, Bruce J. Dalrymple +1 more

We have characterized Nb analog to digital converters using a resistor-coupled SFQ flip flop counter and a latching destructive readout (DRO). The counter used SFQ buffers between bits to provide isolation during destructive readout. We have measured parallel readout at sample rates up to 125 MSPS. We have also successfully operated an ADC which has Josephson junction regulated flip flop gate and readout bias busses. Using a self-resetting gate (SRG) at the carry out of the counter, we have measured the bit error rates (BER) of the counters. A two junction SQUID quantizer, biased in the voltage state, was used to produce correlated SFQ pulses at each junction. The SRG outputs of two 10 bit counters connected to the two quantizer outputs were compared. We measured a BER of /spl sim/5/spl times/10/sup -11/ with the quantizer operating at 19 GHz. We believe the principle error source is the latching SRG.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•1 citation

4.6 GHz SFQ shift register and SFQ pseudorandom bit sequence generator

Joonhee Kang, A. Hodge Worsham, John X. Przybysz

Superconductive electronics can provide low power, GHz speed spread spectrum satellite communications. The key components to construct the spread spectrum modem are an analog filter and a digital pseudorandom bit sequence generator, Various SFQ logic circuits are required to construct a code generator. These circuits include a shift register, a reset switch, and an XOR or XNOR. To make a 4 bit 15 sequence code generator, a four stage shift register with a fan-out of two on each stage was designed. These circuits, fabricated with eight level Nb/AlO/sub x//Nb Josephson junction integrated circuit process, showed correct operation at low speed digital tests. The low speed digital test was done by using a "catcher", the combination of a read SQUID and a Josephson transmission line (JTL) which were magnetically coupled to each other. High speed testing of the shift register used a latch amplifier, which amplified an SFQ pulse to a latching output voltage of about 2 mV. This test showed correct operation of the shift register at speeds of up to 4.6 GHz.>

IEEE Transactions on Applied Superconductivity•Jun 1, 1995•23 citations

Temperature-dependent bit-error rate of a clocked superconducting digital circuit

Quentin Herr, M.W. Johnson, M. J. Feldman

We measured the bit-error rate (BER) of an RS latch, a clocked SFQ circuit. A digital error-detection circuit was used to detect BER in the range unity to 10/sup -13/; below 10/sup -7/, the circuit was operated with a 12 GHz on-chip clock. BER was measured as a function of control current; both positive and negative control current was applied, leading to two distinct modes of error incidence. The error function curves extrapolate to 10/sup -80/ for optimal control current at a temperature of 5.5 K. Measurements were repeated over the range 3-7 K. Comparison to theoretical error-function estimates of BER indicate that the noise is strictly thermal.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•29 citations

Pulse jitter and timing errors in RSFQ circuits

Alexander V. Rylyakov, Konstantin K. Likharev

We have carried out measurements of bit error rate (BER) of Rapid Single-Flux-Quantum (RSFQ) XOR gates with various nominal dc power supply voltages (from 0.1 V to 1.0 mV), operating at speeds up to 25 GHz. (For these gates, implemented using HYPRES' standard, 3.5-/spl mu/m, 10 /spl mu/A//spl mu/m/sup 2/ Nb-trilayer process, this speed is close to maximum.) A special on-chip RSFQ test circuit allowed high-speed measurements of BER in the range from 10/sup -9/ to 10/sup -13/ to be carried out. As a result of these experiments, a new type of thermal-fluctuation-induced digital errors in RSFQ circuits has been identified. These "timing" errors arise at high speed due to time jitter of data and clock pulses. We have developed a simple theory of these errors which allows a fair description of the experimental data. The theory shows that in some cases the timing errors may be an important factor limiting speed performance of RSFQ circuitry. Nevertheless, our XOR gates could operate at 25 GHz with BER below 10/sup -13/ at the standard temperature (4.2 K) at any dc power supply voltage in our range. For the lowest voltage (0.1 Volt) the calculated static power dissipation in the gate was as low as 23 nanowatts, lower than the unavoidable dynamic dissipation (43 nanowatts).

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•69 citations

Improvement of a bit error rate measuring system for high-temperature superconducting circuits

Masahiro Horibe, Kazuhiro Shimaoka, Y. Tarutani +1 more

We have evaluated and tried to improve the measurement precision of a bit error rate (BER) measuring system for superconducting circuits equipped with a magnetic shield and a cryocooler. A noise model has suggested that the most effective way of improving BER is to reduce the noise figure of the wideband pulse amplifier (WPA). BER measurement using a 3-Gbps, 2/sup 15/-1 pseudo random binary signal showed that by using low-noise WPA (noisefigure=4 dB) a 12.0-mV output voltage is required to obtain a minimum BER of 1.19/spl times/10/sup -15/ (a 10/sup -7/ improvement over the previous system) for a 50 /spl Omega/ standard microstrip. A BER of a La/sub 0.2/Yb/sub 0.9/Ba/sub 1.9/Cu/sub 3/O/sub x//MgO/Au microstrip-line to coplanar-waveguide transition-line converter (MCC) was also measured. It was found that the minimum BER was 4.87/spl times/10/sup -13/ (a 10/sup -5/ improvement over the previous system) when the output voltage was 23.8-mV. However these measured BER values were larger than those expected by the noise model. The cause of the larger measured BER is discussed. A minimum BER of 3.64/spl times/10/sup -55/ in 14.8-mV output voltage for a 50 /spl Omega/ standard microstrip was obtained when the cryo-cooler was not operated (without the noise from a cryo-cooler).

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•3 citations
A new method of analyzing bit error rates (BERs) for SFQ circuits and their outputs at GHz speeds will be presented. This method was used to test four- and six-bit pseudorandom code generators. The code generators were operated in free-run mode, i.e., without a synchronization (Reset) pulse. This enabled us to conduct BER testing to much lower levels than when the code generator is operated in Reset mode. The SFQ circuit output was amplified with a superconducting output latch to give voltage levels suitable for display on a sampling scope. The GHz output data was analyzed by external computer software; this permitted extended tests without user supervision. With the code generators operating in free-run mode, they routinely gave bit error rates (BERs) in the 10/sup -11/ range; the best BER recorded was 1.1*10/sup -13/ (2 errors in /spl sim/2.5 hours) at 2 GHz. We have successfully tested these code generators at frequencies in excess of 3.5 GHz with BERs in the 10/sup -10/ range as well.
A 4 bit 15 sequence SFQ (Single Flux Quantum) pseudorandom bit sequence generator was built with an eight-level Nb/AlO/sub x//Nb Josephson junction integrated circuit process. An SFQ circuit was built into the code generator to enable a rapid restart. The test results showed that the circuit operated correctly at the seed of 3.69 GHz. The XNOR gate and shift register worked correctly at 5 GHz. However, the back delay was longer than 200 psec and the generator acted as a 5 bit 21 sequence code generator at this frequency. At 200 MHz, the code generator was operated continuously to observe its stability. Over the course of two and one half hours, the circuit made only five code errors, indicating a bit error rate of 3/spl times/10/sup -12/. At 2 GHz we collected 10 million samples on the 4023rd bit of the sequence. No wrong signal values were observed, indicating the bit error rate is less than 5/spl times/10/sup -11/ at this frequency.
We have characterized Nb analog to digital converters using a resistor-coupled SFQ flip flop counter and a latching destructive readout (DRO). The counter used SFQ buffers between bits to provide isolation during destructive readout. We have measured parallel readout at sample rates up to 125 MSPS. We have also successfully operated an ADC which has Josephson junction regulated flip flop gate and readout bias busses. Using a self-resetting gate (SRG) at the carry out of the counter, we have measured the bit error rates (BER) of the counters. A two junction SQUID quantizer, biased in the voltage state, was used to produce correlated SFQ pulses at each junction. The SRG outputs of two 10 bit counters connected to the two quantizer outputs were compared. We measured a BER of /spl sim/5/spl times/10/sup -11/ with the quantizer operating at 19 GHz. We believe the principle error source is the latching SRG.
Superconductive electronics can provide low power, GHz speed spread spectrum satellite communications. The key components to construct the spread spectrum modem are an analog filter and a digital pseudorandom bit sequence generator, Various SFQ logic circuits are required to construct a code generator. These circuits include a shift register, a reset switch, and an XOR or XNOR. To make a 4 bit 15 sequence code generator, a four stage shift register with a fan-out of two on each stage was designed. These circuits, fabricated with eight level Nb/AlO/sub x//Nb Josephson junction integrated circuit process, showed correct operation at low speed digital tests. The low speed digital test was done by using a "catcher", the combination of a read SQUID and a Josephson transmission line (JTL) which were magnetically coupled to each other. High speed testing of the shift register used a latch amplifier, which amplified an SFQ pulse to a latching output voltage of about 2 mV. This test showed correct operation of the shift register at speeds of up to 4.6 GHz.>
We measured the bit-error rate (BER) of an RS latch, a clocked SFQ circuit. A digital error-detection circuit was used to detect BER in the range unity to 10/sup -13/; below 10/sup -7/, the circuit was operated with a 12 GHz on-chip clock. BER was measured as a function of control current; both positive and negative control current was applied, leading to two distinct modes of error incidence. The error function curves extrapolate to 10/sup -80/ for optimal control current at a temperature of 5.5 K. Measurements were repeated over the range 3-7 K. Comparison to theoretical error-function estimates of BER indicate that the noise is strictly thermal.
We have carried out measurements of bit error rate (BER) of Rapid Single-Flux-Quantum (RSFQ) XOR gates with various nominal dc power supply voltages (from 0.1 V to 1.0 mV), operating at speeds up to 25 GHz. (For these gates, implemented using HYPRES' standard, 3.5-/spl mu/m, 10 /spl mu/A//spl mu/m/sup 2/ Nb-trilayer process, this speed is close to maximum.) A special on-chip RSFQ test circuit allowed high-speed measurements of BER in the range from 10/sup -9/ to 10/sup -13/ to be carried out. As a result of these experiments, a new type of thermal-fluctuation-induced digital errors in RSFQ circuits has been identified. These "timing" errors arise at high speed due to time jitter of data and clock pulses. We have developed a simple theory of these errors which allows a fair description of the experimental data. The theory shows that in some cases the timing errors may be an important factor limiting speed performance of RSFQ circuitry. Nevertheless, our XOR gates could operate at 25 GHz with BER below 10/sup -13/ at the standard temperature (4.2 K) at any dc power supply voltage in our range. For the lowest voltage (0.1 Volt) the calculated static power dissipation in the gate was as low as 23 nanowatts, lower than the unavoidable dynamic dissipation (43 nanowatts).
We have evaluated and tried to improve the measurement precision of a bit error rate (BER) measuring system for superconducting circuits equipped with a magnetic shield and a cryocooler. A noise model has suggested that the most effective way of improving BER is to reduce the noise figure of the wideband pulse amplifier (WPA). BER measurement using a 3-Gbps, 2/sup 15/-1 pseudo random binary signal showed that by using low-noise WPA (noisefigure=4 dB) a 12.0-mV output voltage is required to obtain a minimum BER of 1.19/spl times/10/sup -15/ (a 10/sup -7/ improvement over the previous system) for a 50 /spl Omega/ standard microstrip. A BER of a La/sub 0.2/Yb/sub 0.9/Ba/sub 1.9/Cu/sub 3/O/sub x//MgO/Au microstrip-line to coplanar-waveguide transition-line converter (MCC) was also measured. It was found that the minimum BER was 4.87/spl times/10/sup -13/ (a 10/sup -5/ improvement over the previous system) when the output voltage was 23.8-mV. However these measured BER values were larger than those expected by the noise model. The cause of the larger measured BER is discussed. A minimum BER of 3.64/spl times/10/sup -55/ in 14.8-mV output voltage for a 50 /spl Omega/ standard microstrip was obtained when the cryo-cooler was not operated (without the noise from a cryo-cooler).