Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Tunable transformer for qubits based on flux states

Timur V. Filippov, Sergey K. Tolpygo, Jaan Männik, James E. Lukens

Published Jun 1, 2003• 27 citations
Publisher

Abstract

Flux states of an RF SQUID are promising candidates for the implementation of quantum bits (qubits) for quantum computing. Accurate measurements of the flux states, especially in the time domain, require a controllable coupling between a qubit and a readout circuit (e.g., a dc SQUID magnetometer). Since the readout circuit can also be a source of decoherence, such a controllable coupling also allows one to control (minimize) the back action of the magnetometer. For this purpose we suggest a balanced, tunable transformer. This has a gradiometer configuration such that each arm is broken by a small loop containing two Josephson junctions. As a result the inductance of each arm can be adjusted by an applied bias flux. In the symmetrical case there is no coupling between the qubit and the magnetometer while a desired coupling can be achieved by changing the asymmetry of the arms. Similar transformers may be be useful for achieving controllable, lossless coupling that is required between qubits. Theoretical analysis of the noise back action of the transformer as well as preliminary experimental results are presented.

DOI
10.1109/tasc.2003.814125

Related papers

Flux qubit with a large loop size and tunable Josephson junctions

Hui Deng, Haifeng Yu, Guangming Xue +6 more

We present the design of a superconducting flux qubit with a large loop inductance. The large loop inductance is desirable for coupling between qubits. The loop is configured into a gradiometer form that could reduce the interference from environmental magnetic noise. A combined Josephson junction, i.e., a DC-SQUID is used to replace the small Josephson junction in the usual 3-JJ (Josephaon junction) flux qubit, leading to a tunable energy gap by using an independent external flux line. We perform numerical calculations to investigate the dependence of the energy gap on qubit parameters such as junction capacitance, critical current, loop inductance, and the ratio of junction energy between small and large junctions in the flux qubit. We suggest a range of values for the parameters.

Chinese Physics B•Apr 1, 2012•2 citations

Low-Back-Action RF SQUID Readout for a Josephson Flux Qubit Measurement

V. I. Shnyrkov, Andrii P. Shapovalov, A.A. Kalenyuk +3 more

Superconducting qubits demonstrate good perspectives as scalable blocks for quantum information processing. These systems can be individually readout, addressed, and controlled, making them some of the most attractive thin-film qubits. Quantum measurements should be performed in order to readout the final state of flux qubits. To observe the dynamics of such systems, one requires a fast magnetometer with exceptional sensitivity and low back-action. We address the problem of reducing the back-action of an RF SQUID readout circuit, which may significantly destroy a Josephson flux qubit in the case of the circuits integration. The main sources of such back-action in conventional RF SQUID and DC SQUID circuits are low-ohmic shunting resistors ensuring high damping. The advantage of flux qubits is the presence of an optimal bias point at which, in the first-order approximation, the device is immune to fluctuations in readout and control lines. Nonetheless, even such systems have characteristics limited by a second-order dissipation. The dissipation can be eliminated by using an “ideal parametric readout” based on an RF SQUID acting in non-hysteretic adiabatic mode. In this paper, we propose an RF SQUID in a non-hysteretic regime as a fast, sensitive, and scalable readout system with low back-action for measurements of a single MW photon counter based on a flux qubit.

IEEE International Conference on Electronics and Information Technologies (ELIT)•May 19, 2021•1 citation

Controllable coupling in phase-coupled flux qubits

Mun Dae Kim

We propose a scheme for tunable coupling of phase-coupled flux qubits. The phase-coupling scheme can provide a strong coupling strength of the order of Josephson coupling energy of Josephson junctions in the connecting loop, while the previously studied inductive coupling scheme cannot provide due to small mutual inductance and induced currents. We show that, in order to control the coupling, we need two dc SQUID's in the connecting loop and the control fluxes threading the dc SQUID's must be in opposite directions. The coupling strength is analytically calculated as a function of the control flux at the coresonance point.

arXiv:cond-mat/0602604•Physical Review B•Nov 2, 2006•12 citations

Variable transformer for controllable flux coupling

Maria Gabriella Castellano, F. Chiarello, Roberto Leoni +4 more

We discuss and demonstrate a prototype of superconducting transformer with a flux transfer function that can be varied in a wide range, by acting on a control parameter. The device is realized by inserting a small hysteretic superconducting quantum interference device (dc-SQUID) with unshunted junctions, working as a Josephson junction with flux-controlled critical current, parallel to a superconducting transformer; by varying the magnetic flux coupled to the dc-SQUID, the transfer function for the flux coupled to the transformer can be varied. This feature can prove particularly appealing in the field of quantum computing, where it could be exploited to achieve a controllable magnetic coupling among flux-based qubits. Measurements carried out on a prototype at 4.2K show a reduction factor of about 30 between the “on” and the “off” states. We discuss the system characteristics and the experimental results.

Applied Physics Letters•Apr 1, 2005•26 citations

Efficiency of underdamped dc SQUIDs as readout devices for flux qubits

Shaoxiong Li, Yang Yu, Wei Qiu +2 more

The flux state quantum bit (qubit) is promising for a solid state implementation of scalable quantum computing. The simplest flux state qubit consists of an rf SQUID with two fluxoid states, which can be readout with a dc SQUID - the most sensitive magnetic flux detector. Efficient readout with less back-action is desirable for quantum computing. In this work, we report measurements of the switching flux and switching current distributions of under damped dc SQUIDs. The data show that single shot readout of flux qubit with very high efficiency (>99%) can be realized using underdamped hysteretic dc SQUIDs.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•2 citations

Gradiometric flux qubits with a tunable gap

M J Schwarz, J Goetz, Z Jiang +4 more

For gradiometric three-Josephson-junction flux qubits, we perform a systematic study on the tuning of the minimal transition frequency, the so-called qubit gap. By replacing one of the qubit's Josephson junctions by a dc superconducting quantum interference device (SQUID), the critical current of this SQUID and, in turn, the qubit gap can be tuned in situ by a control flux threading the SQUID loop. We present spectroscopic measurements demonstrating a well-defined controllability of the qubit gap between zero and more than 10 GHz. This is important for tuning the qubit into and out of resonance with other superconducting quantum circuits in scalable architectures, while still operating it at its symmetry point with optimal dephasing properties. The experimental data agree very well with model calculations based on the full qubit Hamiltonian. From a numerical fit, we determine the Josephson coupling and the charging energies of the qubit junctions. The derived values agree well with those measured for other junctions fabricated on the same chip. We also demonstrate the biasing of gradiometric flux qubits near the symmetry point by trapping an odd number of flux quanta in the gradiometer loop. In this way, we study the effect of the significant kinetic inductance, thereby obtaining valuable information for the qubit design.

arXiv:1210.3982•New Journal of Physics•Apr 4, 2013•39 citations
Flux states of an RF SQUID are promising candidates for the implementation of quantum bits (qubits) for quantum computing. Accurate measurements of the flux states, especially in the time domain, require a controllable coupling between a qubit and a readout circuit (e.g., a dc SQUID magnetometer). Since the readout circuit can also be a source of decoherence, such a controllable coupling also allows one to control (minimize) the back action of the magnetometer. For this purpose we suggest a balanced, tunable transformer. This has a gradiometer configuration such that each arm is broken by a small loop containing two Josephson junctions. As a result the inductance of each arm can be adjusted by an applied bias flux. In the symmetrical case there is no coupling between the qubit and the magnetometer while a desired coupling can be achieved by changing the asymmetry of the arms. Similar transformers may be be useful for achieving controllable, lossless coupling that is required between qubits. Theoretical analysis of the noise back action of the transformer as well as preliminary experimental results are presented.
We present the design of a superconducting flux qubit with a large loop inductance. The large loop inductance is desirable for coupling between qubits. The loop is configured into a gradiometer form that could reduce the interference from environmental magnetic noise. A combined Josephson junction, i.e., a DC-SQUID is used to replace the small Josephson junction in the usual 3-JJ (Josephaon junction) flux qubit, leading to a tunable energy gap by using an independent external flux line. We perform numerical calculations to investigate the dependence of the energy gap on qubit parameters such as junction capacitance, critical current, loop inductance, and the ratio of junction energy between small and large junctions in the flux qubit. We suggest a range of values for the parameters.
Superconducting qubits demonstrate good perspectives as scalable blocks for quantum information processing. These systems can be individually readout, addressed, and controlled, making them some of the most attractive thin-film qubits. Quantum measurements should be performed in order to readout the final state of flux qubits. To observe the dynamics of such systems, one requires a fast magnetometer with exceptional sensitivity and low back-action. We address the problem of reducing the back-action of an RF SQUID readout circuit, which may significantly destroy a Josephson flux qubit in the case of the circuits integration. The main sources of such back-action in conventional RF SQUID and DC SQUID circuits are low-ohmic shunting resistors ensuring high damping. The advantage of flux qubits is the presence of an optimal bias point at which, in the first-order approximation, the device is immune to fluctuations in readout and control lines. Nonetheless, even such systems have characteristics limited by a second-order dissipation. The dissipation can be eliminated by using an “ideal parametric readout” based on an RF SQUID acting in non-hysteretic adiabatic mode. In this paper, we propose an RF SQUID in a non-hysteretic regime as a fast, sensitive, and scalable readout system with low back-action for measurements of a single MW photon counter based on a flux qubit.
We propose a scheme for tunable coupling of phase-coupled flux qubits. The phase-coupling scheme can provide a strong coupling strength of the order of Josephson coupling energy of Josephson junctions in the connecting loop, while the previously studied inductive coupling scheme cannot provide due to small mutual inductance and induced currents. We show that, in order to control the coupling, we need two dc SQUID's in the connecting loop and the control fluxes threading the dc SQUID's must be in opposite directions. The coupling strength is analytically calculated as a function of the control flux at the coresonance point.
We discuss and demonstrate a prototype of superconducting transformer with a flux transfer function that can be varied in a wide range, by acting on a control parameter. The device is realized by inserting a small hysteretic superconducting quantum interference device (dc-SQUID) with unshunted junctions, working as a Josephson junction with flux-controlled critical current, parallel to a superconducting transformer; by varying the magnetic flux coupled to the dc-SQUID, the transfer function for the flux coupled to the transformer can be varied. This feature can prove particularly appealing in the field of quantum computing, where it could be exploited to achieve a controllable magnetic coupling among flux-based qubits. Measurements carried out on a prototype at 4.2K show a reduction factor of about 30 between the “on” and the “off” states. We discuss the system characteristics and the experimental results.
The flux state quantum bit (qubit) is promising for a solid state implementation of scalable quantum computing. The simplest flux state qubit consists of an rf SQUID with two fluxoid states, which can be readout with a dc SQUID - the most sensitive magnetic flux detector. Efficient readout with less back-action is desirable for quantum computing. In this work, we report measurements of the switching flux and switching current distributions of under damped dc SQUIDs. The data show that single shot readout of flux qubit with very high efficiency (>99%) can be realized using underdamped hysteretic dc SQUIDs.
For gradiometric three-Josephson-junction flux qubits, we perform a systematic study on the tuning of the minimal transition frequency, the so-called qubit gap. By replacing one of the qubit's Josephson junctions by a dc superconducting quantum interference device (SQUID), the critical current of this SQUID and, in turn, the qubit gap can be tuned in situ by a control flux threading the SQUID loop. We present spectroscopic measurements demonstrating a well-defined controllability of the qubit gap between zero and more than 10 GHz. This is important for tuning the qubit into and out of resonance with other superconducting quantum circuits in scalable architectures, while still operating it at its symmetry point with optimal dephasing properties. The experimental data agree very well with model calculations based on the full qubit Hamiltonian. From a numerical fit, we determine the Josephson coupling and the charging energies of the qubit junctions. The derived values agree well with those measured for other junctions fabricated on the same chip. We also demonstrate the biasing of gradiometric flux qubits near the symmetry point by trapping an odd number of flux quanta in the gradiometer loop. In this way, we study the effect of the significant kinetic inductance, thereby obtaining valuable information for the qubit design.