Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Japanese Journal of Applied Physics

A Simple and Stable Microwave SQUID

Yoshiko Kikuchi, Yukinobu Miki, Taizō Masumi

Published May 1, 1980• 2 citations
Publisher

Abstract

A new, simple and stable type of microwave SQUID has been developed successfully at 10 GHz by using a bridge type junction which can be fabricated very easily. In consequence of adopting a junction of this type, the microwave SQUID has the merit of being free from adjustment and endures several heating cycles between room and liquid He temperatures. This type of SQUID has a slightly poorer S/N ratio, to be improved in future, but has the same characteristics as previously reported SQUIDs with a point contact junction.

DOI
10.1143/jjap.19.l239

Related papers

High Bias Frequency Operation of a Microwave SQUID at 35 GHz

Yukinobu Miki, Taizō Masumi

An rf-SQUID with the bias frequency raised to 35 GHz has been successfully operated for the first time. The principle of designing the SQUID is the naive extension of the SQUIDs at 10 GHz previously reported to the millimeter wave region. At present, the SQUID at 35 GHz has a slightly poorer signal-to-noise ratio than the SQUIDs at 10 GHz and also the highest limit of the output band-width is confined to about 1 MHz. However, several possibilities for improving the style and configuration remain for the future.

Japanese Journal of Applied Physics•Aug 1, 1980•0 citations

High sensitivity microwave SQUID

J. N. Hollenhorst, R. P. Giffard

We have measured the characteristics of a novel SQUID magnetometer pumped at 9 GHz. The device comprises a niobium point-contact shunting a low impedance superconducting microwave transmission line which isolates the junction at high frequencies from a toroidal input transformer. The junction is matched to a 50 Ω coaxial transmission line and the SQUID is operated in a reflection mode. For low values of the weak link critical current we observe a modulation of the phase of the reflected microwave signal periodic in the applied flux. The modulation persists at high microwave power levels indicating that the junction response is maintained to at least 200 GHz. For large values of critical current, amplitude modulation is observed. We have obtained a differential sideband power of 230 pW/(\Phi_{0})^{2}which is close to the value predicted by a simple model. In flux-locked loop operation we have obtained an energy sensitivity referred to the input terminals of 7 × 10-31J/Hz, which is superior to that so far reported for any other SQUID.

IEEE Transactions on Magnetics•Jan 1, 1979•36 citations

Integrated microwave SQUID

A. D. Smith, R. W. Simon, John F. Burch +2 more

We describe the properties of the single junction SQUID operated at microwave frequencies. The low inductance SQUID is fabricated in a thin film format and tightly coupled to an integrated superconducting transmission line and transformer. We discuss new modes of operation and opportunities for improved device and circuit performance.

IEEE Transactions on Magnetics•Mar 1, 1987•7 citations

An Ultrafast Operation of Microwave SQUID's Biased at 35 GHz

Hiroo Fuma, Yukinobu Miki, Taizō Masumi

A microwave SQUID biased at 35 GHz with a Nb point contact has been improved in its characteristic performance, by changing the configuration of a SQUID, from the 35 GHz size to the 9 GHz size which is oversize for the 35 GHz microwave. About a 10 times larger signal output and higher frequency response up to 100 MHz have been directly obtained. Further, it has been confirmed for the first time that the SQUID biased at 35 GHz does respond up to the 9 GHz input signal by using the Bessel function method.

Japanese Journal of Applied Physics•Oct 1, 1980•2 citations

Properties of the microwave SQUID with an YBaCuO point contact junction

Tapani Ryhänen, Heikki Seppä

A high-sensitivity microwave SQUID (superconducting quantum interference device), suitable for RF attenuation measurements, is constructed taking advantage of the low density of states of current carriers in high-T/sub c/ materials. The dynamics, the noise properties, and the sensitivity of the microwave SQUID are theoretically analyzed. The ultimate energy resolution of the waveguide SQUID is inversely proportional to the characteristic frequency omega /sub c/=R/sub q//L of the loop. omega /sub c/ is high for YBaCuO junctions at 4.2 K because of small leakage. A flux sensitivity of 4*10/sup 4-6/ phi /sub 0// square root Hz has been achieved, which is in good agreement with the theoretical predictions.>

IEEE Transactions on Magnetics•Mar 1, 1989•2 citations

An Adjustable rf-Biased SQUID

D. M. Strayer, R. M. Catchings, Tom Oversluizen +1 more

A symmetric rf-biased point-contact superconducting quantum interference device, which can be adjusted while in operation at low temperatures, is described. The device retains the inherent stability and other features of the symmetric rf-biased SQUID while increasing its flexibility, reliability, and even convenience with a simple adjustment feature.

Review of Scientific Instruments•Sep 1, 1973•0 citations
A new, simple and stable type of microwave SQUID has been developed successfully at 10 GHz by using a bridge type junction which can be fabricated very easily. In consequence of adopting a junction of this type, the microwave SQUID has the merit of being free from adjustment and endures several heating cycles between room and liquid He temperatures. This type of SQUID has a slightly poorer S/N ratio, to be improved in future, but has the same characteristics as previously reported SQUIDs with a point contact junction.
An rf-SQUID with the bias frequency raised to 35 GHz has been successfully operated for the first time. The principle of designing the SQUID is the naive extension of the SQUIDs at 10 GHz previously reported to the millimeter wave region. At present, the SQUID at 35 GHz has a slightly poorer signal-to-noise ratio than the SQUIDs at 10 GHz and also the highest limit of the output band-width is confined to about 1 MHz. However, several possibilities for improving the style and configuration remain for the future.
We have measured the characteristics of a novel SQUID magnetometer pumped at 9 GHz. The device comprises a niobium point-contact shunting a low impedance superconducting microwave transmission line which isolates the junction at high frequencies from a toroidal input transformer. The junction is matched to a 50 Ω coaxial transmission line and the SQUID is operated in a reflection mode. For low values of the weak link critical current we observe a modulation of the phase of the reflected microwave signal periodic in the applied flux. The modulation persists at high microwave power levels indicating that the junction response is maintained to at least 200 GHz. For large values of critical current, amplitude modulation is observed. We have obtained a differential sideband power of 230 pW/(\Phi_{0})^{2}which is close to the value predicted by a simple model. In flux-locked loop operation we have obtained an energy sensitivity referred to the input terminals of 7 × 10-31J/Hz, which is superior to that so far reported for any other SQUID.
A microwave SQUID biased at 35 GHz with a Nb point contact has been improved in its characteristic performance, by changing the configuration of a SQUID, from the 35 GHz size to the 9 GHz size which is oversize for the 35 GHz microwave. About a 10 times larger signal output and higher frequency response up to 100 MHz have been directly obtained. Further, it has been confirmed for the first time that the SQUID biased at 35 GHz does respond up to the 9 GHz input signal by using the Bessel function method.
A high-sensitivity microwave SQUID (superconducting quantum interference device), suitable for RF attenuation measurements, is constructed taking advantage of the low density of states of current carriers in high-T/sub c/ materials. The dynamics, the noise properties, and the sensitivity of the microwave SQUID are theoretically analyzed. The ultimate energy resolution of the waveguide SQUID is inversely proportional to the characteristic frequency omega /sub c/=R/sub q//L of the loop. omega /sub c/ is high for YBaCuO junctions at 4.2 K because of small leakage. A flux sensitivity of 4*10/sup 4-6/ phi /sub 0// square root Hz has been achieved, which is in good agreement with the theoretical predictions.>