Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE International Superconductive Electronics Conference (ISEC)

Superconducting digital-RF receiver with high-speed data recording capability

A. Erik Lehmann, Dmitri E. Kirichenko, Alex F. Kirichenko, Saad M. Sarwana, Deepnarayan Gupta

Published Jul 1, 2013• 2 citations
Publisher

Abstract

A superconducting digital-RF receiver with high ingest-rate data recording capability has been developed. The data recorder unit uses standard PC components with state-of-the-art solid-state drives and interfaces with the superconductor analog-to-digital converter (ADC) through a commercial FPGA board. High-speed data ingest rates exceeding 3.2 GBps have been demonstrated successfully with single-bit ADCs clocked up to 27.52 GHz. Long data acquisitions are useful for analyzing ADC performance in terms of stability and linearity. A data analysis program has also been developed to extract performance parameters and visualize digitized signals in frequency and time domains.

DOI
10.1109/isec.2013.6604274

Related papers

Superconductor analog-to-digital converters and their applications

Deepnarayan Gupta, Amol Inamdar, Dmitri E. Kirichenko +2 more

A wide variety of applications, ranging from radio-frequency (RF) receivers for broadband communications and signal detection, on earth and in space, would benefit from high-performance superconductor analog-to-digital converters (ADCs), based on magnetic flux quantization and fast switching Josephson junctions. Superconductor ADCs are capable of very high sample rates (100 GHz or more), very high linearity, and high sensitivity. Nyquist-rate ADCs use the high sample rate to digitize a wide instantaneous bandwidth (tens of GHz) and are useful for wideband spectrum monitoring as well as high-end scientific instrumentation. Delta and delta-sigma oversampling ADCs use the high linearity to achieve programmable trade-off between dynamic range and instantaneous bandwidth. These lowpass and bandpass ADCs have been used for direct digitization of narrower (tens to hundreds of MHz) RF bands in the 1-20 GHz range for a variety of communications, intelligence, electronic warfare, and radar applications. Another application area of these cryogenic ADCs is for outputs of cryogenic sensor arrays and terahertz mixers. Recent advances in various classes of ADCs for different applications are described.

IEEE MTT-S International Microwave Symposium digest•Jun 1, 2011•23 citations

High Performance HF-VHF All Digital RF Receiver Tested at 20 GHz Clock Frequencies

Anna De Escobar, Richard Hitt, Oleg A. Mukhanov +1 more

Wireless applications would be less expensive, more flexible, and more robust if they had more digital and less analog circuitry. The problem is implementing digital signal processing at radio frequencies. Conventional data converters (ADCs and DACs) and digital circuits are simply not fast enough. However, superconductors can provide ultra fast mixed signal and digital circuits with the linearity and dynamic range required for true direct, digital-RF processing. These superconducting circuits are digital ICs based on Josephson junctions and "rapid-single-flux-quantum" logic (RSFQ), where switching speeds up to 750 GHz have been demonstrated enabling true digital-RF architecture at clock speeds eventually up to 160 GHz. This permits direct conversion between analog RF and digital baseband signals, replacing frequency and protocol-specific analog hardware with flexible digital processors. Data conversion in high frequency wireless applications at frequencies up to 50 GHz will soon become practical. Hypres recently delivered a HF-VHF all digital RF receiver (ADR) prototype to ONR. Testing of this ADR has demonstrated the superior performance of superconducting ICs in cryocooled systems. A US Navy laboratory is now evaluating the world's first complete prototype digital RF receiver capable of direct digitization from DC to 2 GHz

IEEE Military Communications Conference (MILCOM)•Oct 1, 2006•7 citations

Superconductor analog-to-digital converters

Oleg A. Mukhanov, Deepnarayan Gupta, Alan M. Kadin +1 more

Ultrafast switching speed, low power, natural quantization of magnetic flux, quantum accuracy, and low noise of cryogenic superconductor circuits enable fast and accurate data conversion between the analog and digital domains. Based on rapid single-flux quantum (RSFQ) logic, these integrated circuits are capable of achieving performance levels unattainable by any other technology. Two major classes of superconductor analog-to-digital converters (ADCs) are being developed - Nyquist sampling and oversampling converters. Complete systems with digital sampling at rates of /spl sim/20 GHz and above have been demonstrated using low-temperature superconductor device technology. Some ADC components have also been implemented using high-temperature superconductors. Superconductor ADCs have unique applications in true digital-RF communications, broadband instrumentation, and digital sensor readout. Their designs, test results, and future development trends are reviewed.

Proceedings of the IEEE•Sep 20, 2004•182 citations

Superconducting delta ADC with on-chip decimation filter

Vasili K. Semenov, Y.A. Polyakov, Timur V. Filippov

Last year we presented the first fully operational superconducting Analog-to-Digital Converter (ADC) with on-chip Digital Signal Processing (DSP). Here we review this device and introduce completed and prospective innovations required to exceed the performance of the best semiconductor counterparts. The ADC chip contains 2 basic parts: a "fundamental" ADC operating at about 20 GHz sampling rate and a digital decimation filter which attenuates high-frequency noise components and reduces the sampling rate to match it with the bandwidth of an input signal. Our short term goal is to achieve 14 bits Spurious Free Dynamic Range (SFDR) for 60 MHz signal bandwidth by using the standard 1000 A/cm/sup 2/ Nb-trilayer fabrication technology commercially available at HYPRES, Inc.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•27 citations

Analysis of superconducting analog-to-digital converter front-end for improved resolution and large dynamic range

Pascal Febvre, Héla Gassara, Patricia Desgreys +1 more

Analog-to-digital converters (ADCs) are key components of most digital systems, as the necessary interface between the analogue world to send and receive signals. Semiconductor ADC systems are intrinsically limited to low frequency ranges of a few GHz and associated to dynamic ranges limited by linearity issues. Superconductor electronic ADCs rely on the magnetic flux quantization and do not suffer from the linearity issues. Moreover, the Rapid-Single-Flux Quantum (RSFQ) technique [1] allows the sampling of signals far in the microwave range, of the order of 100 GHz for the fastest circuits with state-of-the-art low critical temperature niobium-based technology.Two main applications require the use of fast and high dynamic range superconducting ADCs: future ground- or space-based telecommunication systems for software defined radio (SDR) and all systems requiring very high dynamic range in the 120-180 dB range. In this last category, one can find the digital Superconducting Quantum Interference Devices (SQUIDs) that combine the digitization due to the RSFQ technique, with the ultrasensitive sensing of magnetic fields, that are of interest for several applications, ranging from Non-Destructive Evaluation (NDE) to the detection of faint geomagnetic signatures [2].In this work, we will describe in details an analysis of performances of two different kinds of ADCs, respectively for space and geophysics applications. New designs with their electrical circuits will be described for operation in the microwave frequency band with a sigma-delta architecture, and for improved dynamic range with a delta design. The performance in terms of number of bits or dynamic range, frequency bandwidth and ultimate sampling speed will be compared with the ones of existing ADCs. Considerations about the layout due to technological considerations are taken into account in the design. Trade-offs between performance and technologies will be emphasized.[1] K. Likharev and V. Semenov, IEEE Trans. Appl. Supercond. 1, 3 (1991).[2] T. Reich, P. Febvre, T. Ortlepp, F. H. Uhlmann, J. Kunert, R. Stolz, and H.-G. Meyer, Journal of Applied Physics 104(2), 024509 (2008).

•Apr 25, 2010•0 citations

Superconductor Digital-RF Transceiver Components

Oleg A. Mukhanov, Deepnarayan Gupta, Alan M. Kadin +3 more

Superconductive technology offers unparalleled digital and mixed-signal circuit performance, advancing digital processing from baseband to RF stages. This allows elimination of analog filters and mixers with generally poorly controlled phase performance, causing intersymbol interference limiting an overall communication system performance. HYPRES has been developing superconducting circuit components for application to digital RF communication transceivers. The components include low-pass and band-pass analog-to-digital converters, digital decimation and correlation-based filters, digital up/down-converters, and low-time-jitter clock sources. All of these are based on ultra-fast Rapid Single Flux Quantum (RSFQ) digital circuits, with clock rates up to 20 GHz demonstrated with 3-micron technology, and being scaled to 40 GHz and above. In this paper, we will discuss design and performance of some of these components. 1.

•Jan 1, 2006•7 citations
A superconducting digital-RF receiver with high ingest-rate data recording capability has been developed. The data recorder unit uses standard PC components with state-of-the-art solid-state drives and interfaces with the superconductor analog-to-digital converter (ADC) through a commercial FPGA board. High-speed data ingest rates exceeding 3.2 GBps have been demonstrated successfully with single-bit ADCs clocked up to 27.52 GHz. Long data acquisitions are useful for analyzing ADC performance in terms of stability and linearity. A data analysis program has also been developed to extract performance parameters and visualize digitized signals in frequency and time domains.
A wide variety of applications, ranging from radio-frequency (RF) receivers for broadband communications and signal detection, on earth and in space, would benefit from high-performance superconductor analog-to-digital converters (ADCs), based on magnetic flux quantization and fast switching Josephson junctions. Superconductor ADCs are capable of very high sample rates (100 GHz or more), very high linearity, and high sensitivity. Nyquist-rate ADCs use the high sample rate to digitize a wide instantaneous bandwidth (tens of GHz) and are useful for wideband spectrum monitoring as well as high-end scientific instrumentation. Delta and delta-sigma oversampling ADCs use the high linearity to achieve programmable trade-off between dynamic range and instantaneous bandwidth. These lowpass and bandpass ADCs have been used for direct digitization of narrower (tens to hundreds of MHz) RF bands in the 1-20 GHz range for a variety of communications, intelligence, electronic warfare, and radar applications. Another application area of these cryogenic ADCs is for outputs of cryogenic sensor arrays and terahertz mixers. Recent advances in various classes of ADCs for different applications are described.
Wireless applications would be less expensive, more flexible, and more robust if they had more digital and less analog circuitry. The problem is implementing digital signal processing at radio frequencies. Conventional data converters (ADCs and DACs) and digital circuits are simply not fast enough. However, superconductors can provide ultra fast mixed signal and digital circuits with the linearity and dynamic range required for true direct, digital-RF processing. These superconducting circuits are digital ICs based on Josephson junctions and "rapid-single-flux-quantum" logic (RSFQ), where switching speeds up to 750 GHz have been demonstrated enabling true digital-RF architecture at clock speeds eventually up to 160 GHz. This permits direct conversion between analog RF and digital baseband signals, replacing frequency and protocol-specific analog hardware with flexible digital processors. Data conversion in high frequency wireless applications at frequencies up to 50 GHz will soon become practical. Hypres recently delivered a HF-VHF all digital RF receiver (ADR) prototype to ONR. Testing of this ADR has demonstrated the superior performance of superconducting ICs in cryocooled systems. A US Navy laboratory is now evaluating the world's first complete prototype digital RF receiver capable of direct digitization from DC to 2 GHz
Ultrafast switching speed, low power, natural quantization of magnetic flux, quantum accuracy, and low noise of cryogenic superconductor circuits enable fast and accurate data conversion between the analog and digital domains. Based on rapid single-flux quantum (RSFQ) logic, these integrated circuits are capable of achieving performance levels unattainable by any other technology. Two major classes of superconductor analog-to-digital converters (ADCs) are being developed - Nyquist sampling and oversampling converters. Complete systems with digital sampling at rates of /spl sim/20 GHz and above have been demonstrated using low-temperature superconductor device technology. Some ADC components have also been implemented using high-temperature superconductors. Superconductor ADCs have unique applications in true digital-RF communications, broadband instrumentation, and digital sensor readout. Their designs, test results, and future development trends are reviewed.
Last year we presented the first fully operational superconducting Analog-to-Digital Converter (ADC) with on-chip Digital Signal Processing (DSP). Here we review this device and introduce completed and prospective innovations required to exceed the performance of the best semiconductor counterparts. The ADC chip contains 2 basic parts: a "fundamental" ADC operating at about 20 GHz sampling rate and a digital decimation filter which attenuates high-frequency noise components and reduces the sampling rate to match it with the bandwidth of an input signal. Our short term goal is to achieve 14 bits Spurious Free Dynamic Range (SFDR) for 60 MHz signal bandwidth by using the standard 1000 A/cm/sup 2/ Nb-trilayer fabrication technology commercially available at HYPRES, Inc.
Analog-to-digital converters (ADCs) are key components of most digital systems, as the necessary interface between the analogue world to send and receive signals. Semiconductor ADC systems are intrinsically limited to low frequency ranges of a few GHz and associated to dynamic ranges limited by linearity issues. Superconductor electronic ADCs rely on the magnetic flux quantization and do not suffer from the linearity issues. Moreover, the Rapid-Single-Flux Quantum (RSFQ) technique [1] allows the sampling of signals far in the microwave range, of the order of 100 GHz for the fastest circuits with state-of-the-art low critical temperature niobium-based technology.Two main applications require the use of fast and high dynamic range superconducting ADCs: future ground- or space-based telecommunication systems for software defined radio (SDR) and all systems requiring very high dynamic range in the 120-180 dB range. In this last category, one can find the digital Superconducting Quantum Interference Devices (SQUIDs) that combine the digitization due to the RSFQ technique, with the ultrasensitive sensing of magnetic fields, that are of interest for several applications, ranging from Non-Destructive Evaluation (NDE) to the detection of faint geomagnetic signatures [2].In this work, we will describe in details an analysis of performances of two different kinds of ADCs, respectively for space and geophysics applications. New designs with their electrical circuits will be described for operation in the microwave frequency band with a sigma-delta architecture, and for improved dynamic range with a delta design. The performance in terms of number of bits or dynamic range, frequency bandwidth and ultimate sampling speed will be compared with the ones of existing ADCs. Considerations about the layout due to technological considerations are taken into account in the design. Trade-offs between performance and technologies will be emphasized.[1] K. Likharev and V. Semenov, IEEE Trans. Appl. Supercond. 1, 3 (1991).[2] T. Reich, P. Febvre, T. Ortlepp, F. H. Uhlmann, J. Kunert, R. Stolz, and H.-G. Meyer, Journal of Applied Physics 104(2), 024509 (2008).
Superconductive technology offers unparalleled digital and mixed-signal circuit performance, advancing digital processing from baseband to RF stages. This allows elimination of analog filters and mixers with generally poorly controlled phase performance, causing intersymbol interference limiting an overall communication system performance. HYPRES has been developing superconducting circuit components for application to digital RF communication transceivers. The components include low-pass and band-pass analog-to-digital converters, digital decimation and correlation-based filters, digital up/down-converters, and low-time-jitter clock sources. All of these are based on ultra-fast Rapid Single Flux Quantum (RSFQ) digital circuits, with clock rates up to 20 GHz demonstrated with 3-micron technology, and being scaled to 40 GHz and above. In this paper, we will discuss design and performance of some of these components. 1.