Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Superconducting delta ADC with on-chip decimation filter

Vasili K. Semenov, Y.A. Polyakov, Timur V. Filippov

Published Jun 1, 1999• 27 citations
Publisher

Abstract

Last year we presented the first fully operational superconducting Analog-to-Digital Converter (ADC) with on-chip Digital Signal Processing (DSP). Here we review this device and introduce completed and prospective innovations required to exceed the performance of the best semiconductor counterparts. The ADC chip contains 2 basic parts: a "fundamental" ADC operating at about 20 GHz sampling rate and a digital decimation filter which attenuates high-frequency noise components and reduces the sampling rate to match it with the bandwidth of an input signal. Our short term goal is to achieve 14 bits Spurious Free Dynamic Range (SFDR) for 60 MHz signal bandwidth by using the standard 1000 A/cm/sup 2/ Nb-trilayer fabrication technology commercially available at HYPRES, Inc.

DOI
10.1109/77.783666

Related papers

Preliminary results on the analog-to-digital converter based on RSFQ logic

Vasili K. Semenov, Y.A. Polyakov, D.F. Schneider

The first laboratory prototype of a superconductor analog-to-digital converter (ADC) with on-chip fast digital signal processing has been designed and tested at internal clock frequencies up to 7 GHz. Estimated accuracy of the prototype is about 12 bit for 7 MHz signal bandwidth; at lower frequencies the dynamic range increases at least as fast as the reciprocal bandwidth. The single-chip (5/spl times/5 mm/sup 2/) device contains 1778 Josephson junctions and dissipates power at about 0.5 mW.

Conference on Precision Electromagnetic Measurements•Dec 24, 2002•14 citations

Superconductor analog to digital converter for sigint applications

Amol Inamdar, Deepnarayan Gupta, Timur V. Filippov +6 more

Superconductor analog-to-digital converters (ADC) offer high sensitivity and large dynamic range. We report recent advances in the low-pass phase-modulation-demodulation (PMD) oversampled analog-to-digital converter (ADC). The oversampled data from the PMD front-end are passed along with sampling clock to an on-chip digital filter. In the past, the maximum frequency of operation of such chips were limited by that of the digital decimation filter (DDF) to about 30 GHz. Recently, we have designed a chip that allows the PMD front-end to be clocked twice as fast as the DDF, resulting in sampling rates of 46.08 GHz and 29.44 GHz for chips with critical current densities of 4.5 and 1 kA/cm2respectively. We have also designed a new PMD front-end, with a quarter-rate quantizer (QRQ) that allows 18-20 dB extension of dynamic range. We are also pursuing a subranging ADC design with two PMD front-ends connected with fluxon amplifier and subtractor circuitry that promises a dynamic range extension by 25-30 dB. We report signal-to-noise ratio and spur-free dynamic range measurement results for various ADC chips, and project performance for future improvements.

IEEE Military Communications Conference (MILCOM)•Nov 1, 2008•9 citations

High resolution ADC system

Sergey V. Rylov, Lewis A. Bunz, Dmitri V. Gaidarenko +3 more

We have developed and verified experimentally a novel high-resolution superconducting ADC architecture based on phase modulation/demodulation principle and implemented in RSFQ logic. We have demonstrated an ADC chip providing full implementation of this architecture, including on-chip decimation filter and multiple-channel synchronizer. We have also developed a digital ADC evaluation system consisting of an interface electronics block converting the low-voltage ADC output to standard TTL form at multi-MHz sampling rate, and a computerized test station performing data acquisition, processing and display in real time. Using this system we have demonstrated that for low-frequency (kHz) signals our ADC chips possess linearity in excess of 16 bits with Spur-Free Dynamic Range over 108 dB, which is an important benchmark for any high-resolution ADC technology.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•26 citations

Analysis of superconducting analog-to-digital converter front-end for improved resolution and large dynamic range

Pascal Febvre, Héla Gassara, Patricia Desgreys +1 more

Analog-to-digital converters (ADCs) are key components of most digital systems, as the necessary interface between the analogue world to send and receive signals. Semiconductor ADC systems are intrinsically limited to low frequency ranges of a few GHz and associated to dynamic ranges limited by linearity issues. Superconductor electronic ADCs rely on the magnetic flux quantization and do not suffer from the linearity issues. Moreover, the Rapid-Single-Flux Quantum (RSFQ) technique [1] allows the sampling of signals far in the microwave range, of the order of 100 GHz for the fastest circuits with state-of-the-art low critical temperature niobium-based technology.Two main applications require the use of fast and high dynamic range superconducting ADCs: future ground- or space-based telecommunication systems for software defined radio (SDR) and all systems requiring very high dynamic range in the 120-180 dB range. In this last category, one can find the digital Superconducting Quantum Interference Devices (SQUIDs) that combine the digitization due to the RSFQ technique, with the ultrasensitive sensing of magnetic fields, that are of interest for several applications, ranging from Non-Destructive Evaluation (NDE) to the detection of faint geomagnetic signatures [2].In this work, we will describe in details an analysis of performances of two different kinds of ADCs, respectively for space and geophysics applications. New designs with their electrical circuits will be described for operation in the microwave frequency band with a sigma-delta architecture, and for improved dynamic range with a delta design. The performance in terms of number of bits or dynamic range, frequency bandwidth and ultimate sampling speed will be compared with the ones of existing ADCs. Considerations about the layout due to technological considerations are taken into account in the design. Trade-offs between performance and technologies will be emphasized.[1] K. Likharev and V. Semenov, IEEE Trans. Appl. Supercond. 1, 3 (1991).[2] T. Reich, P. Febvre, T. Ortlepp, F. H. Uhlmann, J. Kunert, R. Stolz, and H.-G. Meyer, Journal of Applied Physics 104(2), 024509 (2008).

•Apr 25, 2010•0 citations

Demonstration of the Multi-Bit Sigma-Delta A/D Converter With the Decimation Filter

A. Sekiya, Kenichi Okada, Y. Nishido +2 more

We have proposed a multi-bit sigma-delta analog-to-digital converter (ADC) in which a modulator is composed of a single quantizer and multiple samplers based on the single-flux-quantum (SFQ) circuits. The quantizer converts analog signals to pulse-density-modulated signals, and the samplers sample the modulated SFQ pulses in every sampling clock. Use of multiple samplers based on delayed-flip-flops (DFFs) increases sampling frequencies virtually, resulting in a multi-bit sigma-delta modulator. We also designed a decimation filter by using the well-established Verilog tools for the SFQ circuits and the Matlab simulator. We prepared an ADC including 4 samplers and a second-order decimation filter with the decimation rate of 1:256 based on the Nb junction technology. We confirmed correct operation of this ADC at 56 GHz clock signals generated by an internal ring oscillator. We experimentally obtained the signal-to-noise ratio of 25 dB and spurious-free dynamic range of 37 dB at the bandwidth of 10 MHz from the upper 7 bits of the outputs of the decimation filter.

IEEE Transactions on Applied Superconductivity•Jun 1, 2005•13 citations

Superconductor analog-to-digital converters and their applications

Deepnarayan Gupta, Amol Inamdar, Dmitri E. Kirichenko +2 more

A wide variety of applications, ranging from radio-frequency (RF) receivers for broadband communications and signal detection, on earth and in space, would benefit from high-performance superconductor analog-to-digital converters (ADCs), based on magnetic flux quantization and fast switching Josephson junctions. Superconductor ADCs are capable of very high sample rates (100 GHz or more), very high linearity, and high sensitivity. Nyquist-rate ADCs use the high sample rate to digitize a wide instantaneous bandwidth (tens of GHz) and are useful for wideband spectrum monitoring as well as high-end scientific instrumentation. Delta and delta-sigma oversampling ADCs use the high linearity to achieve programmable trade-off between dynamic range and instantaneous bandwidth. These lowpass and bandpass ADCs have been used for direct digitization of narrower (tens to hundreds of MHz) RF bands in the 1-20 GHz range for a variety of communications, intelligence, electronic warfare, and radar applications. Another application area of these cryogenic ADCs is for outputs of cryogenic sensor arrays and terahertz mixers. Recent advances in various classes of ADCs for different applications are described.

IEEE MTT-S International Microwave Symposium digest•Jun 1, 2011•23 citations
Last year we presented the first fully operational superconducting Analog-to-Digital Converter (ADC) with on-chip Digital Signal Processing (DSP). Here we review this device and introduce completed and prospective innovations required to exceed the performance of the best semiconductor counterparts. The ADC chip contains 2 basic parts: a "fundamental" ADC operating at about 20 GHz sampling rate and a digital decimation filter which attenuates high-frequency noise components and reduces the sampling rate to match it with the bandwidth of an input signal. Our short term goal is to achieve 14 bits Spurious Free Dynamic Range (SFDR) for 60 MHz signal bandwidth by using the standard 1000 A/cm/sup 2/ Nb-trilayer fabrication technology commercially available at HYPRES, Inc.
Superconductor analog-to-digital converters (ADC) offer high sensitivity and large dynamic range. We report recent advances in the low-pass phase-modulation-demodulation (PMD) oversampled analog-to-digital converter (ADC). The oversampled data from the PMD front-end are passed along with sampling clock to an on-chip digital filter. In the past, the maximum frequency of operation of such chips were limited by that of the digital decimation filter (DDF) to about 30 GHz. Recently, we have designed a chip that allows the PMD front-end to be clocked twice as fast as the DDF, resulting in sampling rates of 46.08 GHz and 29.44 GHz for chips with critical current densities of 4.5 and 1 kA/cm2respectively. We have also designed a new PMD front-end, with a quarter-rate quantizer (QRQ) that allows 18-20 dB extension of dynamic range. We are also pursuing a subranging ADC design with two PMD front-ends connected with fluxon amplifier and subtractor circuitry that promises a dynamic range extension by 25-30 dB. We report signal-to-noise ratio and spur-free dynamic range measurement results for various ADC chips, and project performance for future improvements.
We have developed and verified experimentally a novel high-resolution superconducting ADC architecture based on phase modulation/demodulation principle and implemented in RSFQ logic. We have demonstrated an ADC chip providing full implementation of this architecture, including on-chip decimation filter and multiple-channel synchronizer. We have also developed a digital ADC evaluation system consisting of an interface electronics block converting the low-voltage ADC output to standard TTL form at multi-MHz sampling rate, and a computerized test station performing data acquisition, processing and display in real time. Using this system we have demonstrated that for low-frequency (kHz) signals our ADC chips possess linearity in excess of 16 bits with Spur-Free Dynamic Range over 108 dB, which is an important benchmark for any high-resolution ADC technology.
Analog-to-digital converters (ADCs) are key components of most digital systems, as the necessary interface between the analogue world to send and receive signals. Semiconductor ADC systems are intrinsically limited to low frequency ranges of a few GHz and associated to dynamic ranges limited by linearity issues. Superconductor electronic ADCs rely on the magnetic flux quantization and do not suffer from the linearity issues. Moreover, the Rapid-Single-Flux Quantum (RSFQ) technique [1] allows the sampling of signals far in the microwave range, of the order of 100 GHz for the fastest circuits with state-of-the-art low critical temperature niobium-based technology.Two main applications require the use of fast and high dynamic range superconducting ADCs: future ground- or space-based telecommunication systems for software defined radio (SDR) and all systems requiring very high dynamic range in the 120-180 dB range. In this last category, one can find the digital Superconducting Quantum Interference Devices (SQUIDs) that combine the digitization due to the RSFQ technique, with the ultrasensitive sensing of magnetic fields, that are of interest for several applications, ranging from Non-Destructive Evaluation (NDE) to the detection of faint geomagnetic signatures [2].In this work, we will describe in details an analysis of performances of two different kinds of ADCs, respectively for space and geophysics applications. New designs with their electrical circuits will be described for operation in the microwave frequency band with a sigma-delta architecture, and for improved dynamic range with a delta design. The performance in terms of number of bits or dynamic range, frequency bandwidth and ultimate sampling speed will be compared with the ones of existing ADCs. Considerations about the layout due to technological considerations are taken into account in the design. Trade-offs between performance and technologies will be emphasized.[1] K. Likharev and V. Semenov, IEEE Trans. Appl. Supercond. 1, 3 (1991).[2] T. Reich, P. Febvre, T. Ortlepp, F. H. Uhlmann, J. Kunert, R. Stolz, and H.-G. Meyer, Journal of Applied Physics 104(2), 024509 (2008).
We have proposed a multi-bit sigma-delta analog-to-digital converter (ADC) in which a modulator is composed of a single quantizer and multiple samplers based on the single-flux-quantum (SFQ) circuits. The quantizer converts analog signals to pulse-density-modulated signals, and the samplers sample the modulated SFQ pulses in every sampling clock. Use of multiple samplers based on delayed-flip-flops (DFFs) increases sampling frequencies virtually, resulting in a multi-bit sigma-delta modulator. We also designed a decimation filter by using the well-established Verilog tools for the SFQ circuits and the Matlab simulator. We prepared an ADC including 4 samplers and a second-order decimation filter with the decimation rate of 1:256 based on the Nb junction technology. We confirmed correct operation of this ADC at 56 GHz clock signals generated by an internal ring oscillator. We experimentally obtained the signal-to-noise ratio of 25 dB and spurious-free dynamic range of 37 dB at the bandwidth of 10 MHz from the upper 7 bits of the outputs of the decimation filter.
A wide variety of applications, ranging from radio-frequency (RF) receivers for broadband communications and signal detection, on earth and in space, would benefit from high-performance superconductor analog-to-digital converters (ADCs), based on magnetic flux quantization and fast switching Josephson junctions. Superconductor ADCs are capable of very high sample rates (100 GHz or more), very high linearity, and high sensitivity. Nyquist-rate ADCs use the high sample rate to digitize a wide instantaneous bandwidth (tens of GHz) and are useful for wideband spectrum monitoring as well as high-end scientific instrumentation. Delta and delta-sigma oversampling ADCs use the high linearity to achieve programmable trade-off between dynamic range and instantaneous bandwidth. These lowpass and bandpass ADCs have been used for direct digitization of narrower (tens to hundreds of MHz) RF bands in the 1-20 GHz range for a variety of communications, intelligence, electronic warfare, and radar applications. Another application area of these cryogenic ADCs is for outputs of cryogenic sensor arrays and terahertz mixers. Recent advances in various classes of ADCs for different applications are described.