Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE

Experiments with Josephson Junctions Mixers

Gerard ter Horst, Th. de Graauw, R. A. Panhuyzen, H. Schaeffer, Th.J.M. Helmerhorst, T. M. Klapwijk, J. Kortland

Published Apr 21, 1986• 3 citations
Publisher

Abstract

Josephson junctions (JJ) mixers have been developped and in the millimeter (185-270 GHz) and in the sub-millimeter range (345 GHz, 1000 GHz). Pointcontact devices have shown the best noise temperatures (Tsys = 420 K at 230 GHz) but are unreliable for practical operations. The developped planar junctions have gown so far competitive performance with respect to cooled Schottky barrier diode mixers e.g.. Tsys = 1600 K at 345 GHz.

DOI
10.1117/12.952317

Related papers

SUBMM mixing experiments with planar Josephson junction devices

R. A. Panhuyzen, Gerard ter Horst, Th. de Graauw +4 more

Planar Nb-Nb Josephson Junctions (JJ's) have been developed to be used in submillimeter heterodyne mixers. Experimental mixing results show a System Noise Temperature around 1000 K with a best result of 800 K at an operating temperature of 1.5 K. Preliminary results at 900 GHz are reported. A strong temperature dependence of the mixer noise temperature has been observed.

IEEE Transactions on Magnetics•Mar 1, 1987•3 citations

Noise in Josephson effect mm-wave mixers

J. H. Claassen, Y. Taur, P. L. Richards

We have recently shown that point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54K. Both of these results are ∼ 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency\Omega = \hbar \omega/2eI_{c}R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.

IEEE Transactions on Magnetics•Mar 1, 1975•1 citation

Low-noise Josephson mixers at 115 GHz using recyclable point contacts

Y. Taur, Anthony R. Kerr

Thermally recyclable Nb point-contact Josephson junctions are investigated as low-noise mixers with an external local oscillator at 115 GHz. The best single sideband mixer noise temperature achieved is 140 (±20) K with a (SSB) conversion loss of 2.4 (±0.5) dB. Such rugged junctions are suitable for use in practical receivers and should give unprecedented sensitivity at the shorter millimeter wavelengths.

Applied Physics Letters•Jun 1, 1978•32 citations

Progress on millimeter wave Josephson junction mixers

Y. Taur, Anthony R. Kerr

Preset, recyclable Nb point contacts are tested as low‐noise Josephson mixers at a signal frequency of 115 GHz. The best result achieved is a mixer noise temperature (single sideband) of 120 K with unity conversion efficiency (SSB) for a junction at 6 K. Variation of mixer properties with temperature and other parameters is presented.

AIP conference proceedings•Jan 1, 1978•1 citation

Josephson junction mixer using an external local oscillator

Helmut Kanter

Mixing experiments on niobium point contacts are reported for conversion from 95 GHz to 140 MHz. The conversion efficiency is less than predicted by the highly damped weak link model. The discrepancy is presumably due to mixing with higher harmonics of the local oscillator. The lowest noise temperature measured was T ~ 100 K which is of the same order as recently reported for cooled Schottky-barrier diodes.

Revue de Physique Appliquée•Jan 1, 1974•10 citations

Noise in Josephson point contacts with and without rf bias

J. H. Claassen, Y. Taur, P. L. Richards

Point contact Josephson junctions operated as microwave mixers at 36 GHz show conversion gain and lower noise than cooled Schottky barrier diodes in the same application. The noise in such junctions with and without rf bias is explored both experimentally and theoretically. The noise power is found to be about a factor 2 above the thermal noise in the resistively shunted junction model. In contrast to previous reports, the inclusion of a shot noise term in the theory for no rf bias overestimates the observed noise substantially.

Applied Physics Letters•Dec 15, 1974•31 citations
Josephson junctions (JJ) mixers have been developped and in the millimeter (185-270 GHz) and in the sub-millimeter range (345 GHz, 1000 GHz). Pointcontact devices have shown the best noise temperatures (Tsys = 420 K at 230 GHz) but are unreliable for practical operations. The developped planar junctions have gown so far competitive performance with respect to cooled Schottky barrier diode mixers e.g.. Tsys = 1600 K at 345 GHz.
We have recently shown that point contact Josephson junctions can function as millimeter wave heterodyne mixers with conversion gain. The best results achieved thus far show a single sideband conversion gain of 1.3 and a mixer contribution to the system noise temperature of 54K. Both of these results are ∼ 5 times better than the best published figures for cooled Schottky barrier diode mixers operated at the same frequency. The measured noise for a variety of junctions can be expressed as a universal function of the normalized rf frequency\Omega = \hbar \omega/2eI_{c}R. It is about a factor 2 larger than the calculated noise arising from the thermal noise in the junction shunt resistance R. The noise calculation was done for the resistively shunted junction model using an analog junction simulator.
Point contact Josephson junctions operated as microwave mixers at 36 GHz show conversion gain and lower noise than cooled Schottky barrier diodes in the same application. The noise in such junctions with and without rf bias is explored both experimentally and theoretically. The noise power is found to be about a factor 2 above the thermal noise in the resistively shunted junction model. In contrast to previous reports, the inclusion of a shot noise term in the theory for no rf bias overestimates the observed noise substantially.