Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Revue de Physique Appliquée

Josephson junction mixer using an external local oscillator

Helmut Kanter

Published Jan 1, 1974• 10 citations
Publisher

Abstract

Mixing experiments on niobium point contacts are reported for conversion from 95 GHz to 140 MHz. The conversion efficiency is less than predicted by the highly damped weak link model. The discrepancy is presumably due to mixing with higher harmonics of the local oscillator. The lowest noise temperature measured was T ~ 100 K which is of the same order as recently reported for cooled Schottky-barrier diodes.

DOI
10.1051/rphysap:0197400901025500

Related papers

Frequency conversion with superconducting point contacts operating as oscillator-mixers and its application to the measurement of the linewidth of the Josephson current at very high frequency

G. Vernet, Robert Adde

The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb-Nb point contact junctions at 4.2 K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1 and 9.2 GHz. Frequency conversion signals are only detected in the latter case with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1 600 GHz. The experiments with intermediate frequency fi of 0.1 GHz indicate for this small value of f i that the observed signals are not related to frequency conversion but noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. We have then investigated the noise properties up to 450 GHz of superconducting point-contacts using the junction as an oscillator-mixer where the Josephson current is mixed with harmonics of an externally applied signal. The emitted intermediate frequency is detected at 9.2 GHz and its linewidth is measured. In the very high frequency range the dc quasiparticle current dominates in a Josephson weak-link and we compare the corresponding theoretical linewidth calculated by Scalapino with our experimental results.

Revue de Physique Appliquée•Jan 1, 1974•3 citations

Point-contact Josephson mixers at 130 GHz

J. H. Claassen, P. L. Richards

The properties of point-contact Josephson junctions operated as mixers with an external local oscillator at 130 GHz have been studied, and the results compared with predictions of the resistively shunted junction model. It was found that the junction’s output noise could be within a factor of 1.5 of the model prediction based on the thermal-driving noise. When the coupling to the rf source was optimized, a factor of 2 discrepancy was typical. The measured conversion efficiency agreed with the model, within the experimental uncertainty in the equivalent microwave circuit. The best coupling was achieved in full-height waveguide. The best overall performance, measured using the hot/cold source technique, was a single sideband conversion efficiency of 0.30 and a mixer-noise temperature of 180 K (both ±20%). The best junctions were made of Nb, with carefully prepared points. Nonideal behavior in other junctions is ascribed to heating effects. There is some evidence that junctions whose resistance exceeds a threshold value of ∼60 Ω are no longer well described by the RSJ model. A discussion is given of possible improvements in performance with better junctions or improved rf matching.

Journal of Applied Physics•Jul 1, 1978•28 citations

The properties of a heterodyne receiver at 450 GHz using a Josephson point-contact mixer and an external local oscillator

T. G. Blaney, N R Cross, Robert G. Jones

Adjustable niobium Josephson point contacts, mounted in fundamental-mode waveguide cavities, have been used as mixers in an experimental heterodyne receiver with a 450 GHz laser as the local oscillator. It was possible to estimate separately the various factors, such as intrinsic mixer conversion efficiency, mixer noise, and input coupling efficiency that contribute to the overall receiver sensitivity. Mixer performance agreed reasonably well with qualitative predictions of resistively-shunted-junction theoretical models, and there was broad quantitative agreement for some aspects of performance. Spurious, and potentially very misleading non-heterodyne responses to thermal signals were observed under some regimes of applied DC bias and local oscillator power. The lowest overall receiver noise temperature measured was 2100K (double side band), although reduction to 1000K should be possible with quite simple improvements. The intrinsic mixer noise temperatures were usually in the range 500-1000K (single side band), and local oscillator power required by the receiver was usually less than one microwatt. This performance makes these mixers competitive as the basis of very sensitive near-millimetre-wave receivers.

Journal of Physics D Applied Physics•Nov 14, 1982•12 citations

Performance limits of a Josephson-junction mixer

J. H. Claassen, P. L. Richards

We present the results of extensive analog-computer simulations of a Josephson junction used as a mixer with an external local oscillator. The resistively shunted junction model was used throughout, and the effects of intrinsic junction noise were included. When the source impedance is much greater than the junction resistance R, our simulations permit predictions of conversion efficiency, noise temperature, and saturation level to be made for a wide range of experimental parameters. The possibility of harmonic mixing has also been considered. With a source resistance comparable to R (i.e., conventional ’’matching’’) the behavior of the system is too complicated to permit such general predictions of performance. From the results of simulations for a particular set of parameters, it appears that the best noise temperature will usually be achieved for a source impedance somewhat greater than R. An upper limit for the mixer-noise temperature is ∼40T over a broad range of junction parameters, where T is the effective temperature of the junction. The conversion efficiency under these circumstances should be comparable to what is potentially available from Schottky-diode mixers. Our simulations show that with stronger microwave coupling it is possible to obtain conversion gain—i.e., a conversion efficiency exceeding unity. This, however, will probably be at the expense of a higher mixer-noise temperature. Saturation can be important even for source temperatures ∼300 K. To avoid saturation it is necessary either to restrict the coupling bandwith or use an array of junctions.

Journal of Applied Physics•Jul 1, 1978•42 citations

Noise in Josephson point contacts with and without rf bias

J. H. Claassen, Y. Taur, P. L. Richards

Point contact Josephson junctions operated as microwave mixers at 36 GHz show conversion gain and lower noise than cooled Schottky barrier diodes in the same application. The noise in such junctions with and without rf bias is explored both experimentally and theoretically. The noise power is found to be about a factor 2 above the thermal noise in the resistively shunted junction model. In contrast to previous reports, the inclusion of a shot noise term in the theory for no rf bias overestimates the observed noise substantially.

Applied Physics Letters•Dec 15, 1974•31 citations

Low-noise Josephson mixers at 115 GHz using recyclable point contacts

Y. Taur, Anthony R. Kerr

Thermally recyclable Nb point-contact Josephson junctions are investigated as low-noise mixers with an external local oscillator at 115 GHz. The best single sideband mixer noise temperature achieved is 140 (±20) K with a (SSB) conversion loss of 2.4 (±0.5) dB. Such rugged junctions are suitable for use in practical receivers and should give unprecedented sensitivity at the shorter millimeter wavelengths.

Applied Physics Letters•Jun 1, 1978•32 citations
Mixing experiments on niobium point contacts are reported for conversion from 95 GHz to 140 MHz. The conversion efficiency is less than predicted by the highly damped weak link model. The discrepancy is presumably due to mixing with higher harmonics of the local oscillator. The lowest noise temperature measured was T ~ 100 K which is of the same order as recently reported for cooled Schottky-barrier diodes.
The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb-Nb point contact junctions at 4.2 K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1 and 9.2 GHz. Frequency conversion signals are only detected in the latter case with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1 600 GHz. The experiments with intermediate frequency fi of 0.1 GHz indicate for this small value of f i that the observed signals are not related to frequency conversion but noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. We have then investigated the noise properties up to 450 GHz of superconducting point-contacts using the junction as an oscillator-mixer where the Josephson current is mixed with harmonics of an externally applied signal. The emitted intermediate frequency is detected at 9.2 GHz and its linewidth is measured. In the very high frequency range the dc quasiparticle current dominates in a Josephson weak-link and we compare the corresponding theoretical linewidth calculated by Scalapino with our experimental results.
The properties of point-contact Josephson junctions operated as mixers with an external local oscillator at 130 GHz have been studied, and the results compared with predictions of the resistively shunted junction model. It was found that the junction’s output noise could be within a factor of 1.5 of the model prediction based on the thermal-driving noise. When the coupling to the rf source was optimized, a factor of 2 discrepancy was typical. The measured conversion efficiency agreed with the model, within the experimental uncertainty in the equivalent microwave circuit. The best coupling was achieved in full-height waveguide. The best overall performance, measured using the hot/cold source technique, was a single sideband conversion efficiency of 0.30 and a mixer-noise temperature of 180 K (both ±20%). The best junctions were made of Nb, with carefully prepared points. Nonideal behavior in other junctions is ascribed to heating effects. There is some evidence that junctions whose resistance exceeds a threshold value of ∼60 Ω are no longer well described by the RSJ model. A discussion is given of possible improvements in performance with better junctions or improved rf matching.
Adjustable niobium Josephson point contacts, mounted in fundamental-mode waveguide cavities, have been used as mixers in an experimental heterodyne receiver with a 450 GHz laser as the local oscillator. It was possible to estimate separately the various factors, such as intrinsic mixer conversion efficiency, mixer noise, and input coupling efficiency that contribute to the overall receiver sensitivity. Mixer performance agreed reasonably well with qualitative predictions of resistively-shunted-junction theoretical models, and there was broad quantitative agreement for some aspects of performance. Spurious, and potentially very misleading non-heterodyne responses to thermal signals were observed under some regimes of applied DC bias and local oscillator power. The lowest overall receiver noise temperature measured was 2100K (double side band), although reduction to 1000K should be possible with quite simple improvements. The intrinsic mixer noise temperatures were usually in the range 500-1000K (single side band), and local oscillator power required by the receiver was usually less than one microwatt. This performance makes these mixers competitive as the basis of very sensitive near-millimetre-wave receivers.
We present the results of extensive analog-computer simulations of a Josephson junction used as a mixer with an external local oscillator. The resistively shunted junction model was used throughout, and the effects of intrinsic junction noise were included. When the source impedance is much greater than the junction resistance R, our simulations permit predictions of conversion efficiency, noise temperature, and saturation level to be made for a wide range of experimental parameters. The possibility of harmonic mixing has also been considered. With a source resistance comparable to R (i.e., conventional ’’matching’’) the behavior of the system is too complicated to permit such general predictions of performance. From the results of simulations for a particular set of parameters, it appears that the best noise temperature will usually be achieved for a source impedance somewhat greater than R. An upper limit for the mixer-noise temperature is ∼40T over a broad range of junction parameters, where T is the effective temperature of the junction. The conversion efficiency under these circumstances should be comparable to what is potentially available from Schottky-diode mixers. Our simulations show that with stronger microwave coupling it is possible to obtain conversion gain—i.e., a conversion efficiency exceeding unity. This, however, will probably be at the expense of a higher mixer-noise temperature. Saturation can be important even for source temperatures ∼300 K. To avoid saturation it is necessary either to restrict the coupling bandwith or use an array of junctions.
Point contact Josephson junctions operated as microwave mixers at 36 GHz show conversion gain and lower noise than cooled Schottky barrier diodes in the same application. The noise in such junctions with and without rf bias is explored both experimentally and theoretically. The noise power is found to be about a factor 2 above the thermal noise in the resistively shunted junction model. In contrast to previous reports, the inclusion of a shot noise term in the theory for no rf bias overestimates the observed noise substantially.