Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

European Microwave Conference (EuMC)

High Speed Low Power Circuits with Josephson Junctions

W. Jutzi

Published Oct 1, 1981• 0 citations
Publisher

Abstract

After a phenomenologic description of the Josephson effect, performance data of oscillators, detectors, mixers and parametric amplifiers as well as of integrated memory and logic circuits with Josephson junctions are presented.
DOI
10.1109/euma.1981.332981

Related papers

Design of high compression point Josephson junction travelling wave parametric amplifier for readout of millimetre/sub-millimetre astronomical receivers

Javier Navarro Montilla, Boon-Kok Tan

Supra-THz heterodyne mixers generally have higher conversion loss compared to the millimetre-wave mixers. Hence, the overall receiver noise temperature becomes increasingly dominated by the first-stage semiconductor low noise amplifier (LNA), which still struggles to achieve quantum-limited noise performance. Here, we aim to develop a Josephson junction travelling wave parametric amplifier (JTWPA) that can achieve high gain over broad bandwidth but with better noise performance to replace these Intermediate Frequency (IF) amplifiers. JTWPAs are typically considered not suitable for astronomical receivers due to their low power handling capability. However, the critical current of the Josephson junctions (JJ) can be easily engineered to match the output power of the front-end detectors. Nevertheless, this may results in the requirement of a higher number of JJs as the junction inductance is in reverse relation with the critical current. Therefore, in this paper, we aim to explore the different design parameters required for developing a JTWPA with a dynamic range compatible for readout a Superconductor-Insulator-Superconductor (SIS) mixer, as an example. Here, we present two JTWPA models that are suitable for the objective, one requiring 3,142 Nb/Al-AlOx/Nb junctions with a maximum gain of 23 dB, and the other with a lower gain at 16 dB but requires only 1,317 JJs. We then compare the SIS receiver noise performance utilising these JTWPAs with that of using a conventional high gain High Electron Mobility Transistor (HEMT) amplifier. We show that we can improve the receiver sensitivity significantly by either cascading two 23 dB gain JTWPA or using a combination of a 16 dB gain JTWPA and a HEMT amplifier. We conclude that the former option more suitable for large detector array applications as it completely replaces the high heat dissipation HEMT amplifiers; while the latter option is favourable at this stage for low pixel count application as it is easier to fabricate a lower number of junctions JTWPA.

Millimeter, Submillimeter, and Far-Infrared Detectors and Instrumentation for Astronomy XI•Jul 15, 2022•1 citation

Review of Josephson effect detection mechanisms

Sidney Shapiro

Some modes of video, heterodyne, and oscillator-mixer operation of Josephson junctions were reviewed.

Revue de Physique Appliquée•Jan 1, 1974•1 citation

ミリ波・サブミリ波検出器

Kazuo Fujisawa

In this report, Josephson junction detectors for millimeter and submillimeter waves are surveyed. Emphasis is placed on heterodyne detectors (mixers). Others are briefly referred to, such as video detectors, bolometers, quasiparticle mixers and parametric amplifiers. Also, three kinds of Josephson junctions for detector use are mentioned and brief comments are given on them. These are tunnel junctions, thin film microbridges and point contacts.Thermally cyclable oxide barrier tunnel junctions have been obtained and used as low noise quasiparticle mixers at 115GHz. They have lower noise temperatures compared to Josephson effect mixers, but the receiver noise temperatures are not lowered owing to their lower conversion efficiencies. Thin film microbridges suffer from low junction resistances and also from heating effects caused by d.c. bias supply and r.f. incident power. There seems to exist many problems to be overcome in order to make good submillimeter wave detectors by tunnel junctions or microbridges.Point contacts are now widely used as sensitive detectors for millimeter and submillimeter waves. Although there exist difficulties for making rugged and thermally cyclable point contacts, the techniques for making them have made considerable progress, and a new construction of detector mount has appeared, which brought a low noise mixer at 115GHz thermally cyclable.It is shown that the sensitivity of video detectors decreases as proportional to the inverse square of frequency. So, for submillimeter waves, video detectors are inferior to superconducting bolometers.Recent progress in heterodyne detectors (fundamental and harmonic mixers) are touched on. They are superior to Shottky diode mixers in that they have much smaller NEP's and much higher conversion efficiencies (especially in harmonic mixers), and also in that they operate with much smaller LO power. Experimental curves of IF output power v.s. bias voltage are given for harmonic mixers with harmonic number N=7 and N=10. It is noted that harmonic mixers with even harmonic number are preferable, because they can operate at zero bias voltage. Among them, low even numbers 2 or 4 are recommended in regards to good conversion efficiency.By using Josephson junctions, a peculiar parametric operation is possible, namely doubly degenerate mode. This mode operates under zero d.c. bias by choosing pump frequency as 2ωp=ωs+ωi, ωp-ωs-ωi. Zero bias operation allows the adoption of microbridge arrays. A parametric amplifier with 160 microbridge arrays was built at 33GHz, and showed amplifier gain of 15dB and noise temperature of 20K.

TEION KOGAKU (Journal of Cryogenics and Superconductivity Society of Japan)•Jan 1, 1980•0 citations

The use of Josephson junctions as mixers and parametric amplifiers at microwaves

A. Raeisaenen, Panu Somervuo

NASA STI/Recon Technical Report N•Jan 1, 1977•0 citations

Superconductive electronics-a high speed and low power technology complementing III-V technologies for advanced systems

Michael Leung, J.W. Spargo, Kevin W. Kobayashi +1 more

Superconductive electronics offers a unique combination of high bandwidth and low power for mission critical hardware such as digital processors at 20 to 100 GHz, microwatt per bit analog to digital converters, large digital switches at multi-Gb/s data rates, and low noise parametric amplifiers. This cryogenic technology, typically operating at a few degrees or a few tens of degrees Kelvin, depends upon the unique physics of superconducting materials such as Nb, NbN, and YBaCuO, and the fundamental circuit element, the Josephson junction (JJ) to create unique architectures of unprecedented design efficiency and performance. These circuits are based on the single flux quantum (SFQ) logic family, a technology that has no parallel in semiconductor electronics. Digital data is transmitted by voltage pulses with amplitude less than 1 mV, but at extremely high speeds. Individual gates have been operated as high as 370 GHz. In this paper, we present a brief overview of superconductive digital technology, describe some recent circuits, and discuss how the challenges to superconductive technology are being met, including the use of multi-chip module (MCM) technology, and the potential use of III-V HBT and HEMT circuits to provide interface drivers and amplifiers, possibly operated cryogenically.

Technical digest -- IEEE Compound Semiconductor Integrated Circuit Symposium•Nov 23, 2002•1 citation

High Power Josephson Parametric Amplifiers with GHz Bandwidth

Ofer Naaman, D.W. Ferguson, Alex Marakov +3 more

Bulletin of the American Physical Society•Mar 8, 2018•1 citation
Supra-THz heterodyne mixers generally have higher conversion loss compared to the millimetre-wave mixers. Hence, the overall receiver noise temperature becomes increasingly dominated by the first-stage semiconductor low noise amplifier (LNA), which still struggles to achieve quantum-limited noise performance. Here, we aim to develop a Josephson junction travelling wave parametric amplifier (JTWPA) that can achieve high gain over broad bandwidth but with better noise performance to replace these Intermediate Frequency (IF) amplifiers. JTWPAs are typically considered not suitable for astronomical receivers due to their low power handling capability. However, the critical current of the Josephson junctions (JJ) can be easily engineered to match the output power of the front-end detectors. Nevertheless, this may results in the requirement of a higher number of JJs as the junction inductance is in reverse relation with the critical current. Therefore, in this paper, we aim to explore the different design parameters required for developing a JTWPA with a dynamic range compatible for readout a Superconductor-Insulator-Superconductor (SIS) mixer, as an example. Here, we present two JTWPA models that are suitable for the objective, one requiring 3,142 Nb/Al-AlOx/Nb junctions with a maximum gain of 23 dB, and the other with a lower gain at 16 dB but requires only 1,317 JJs. We then compare the SIS receiver noise performance utilising these JTWPAs with that of using a conventional high gain High Electron Mobility Transistor (HEMT) amplifier. We show that we can improve the receiver sensitivity significantly by either cascading two 23 dB gain JTWPA or using a combination of a 16 dB gain JTWPA and a HEMT amplifier. We conclude that the former option more suitable for large detector array applications as it completely replaces the high heat dissipation HEMT amplifiers; while the latter option is favourable at this stage for low pixel count application as it is easier to fabricate a lower number of junctions JTWPA.
In this report, Josephson junction detectors for millimeter and submillimeter waves are surveyed. Emphasis is placed on heterodyne detectors (mixers). Others are briefly referred to, such as video detectors, bolometers, quasiparticle mixers and parametric amplifiers. Also, three kinds of Josephson junctions for detector use are mentioned and brief comments are given on them. These are tunnel junctions, thin film microbridges and point contacts.Thermally cyclable oxide barrier tunnel junctions have been obtained and used as low noise quasiparticle mixers at 115GHz. They have lower noise temperatures compared to Josephson effect mixers, but the receiver noise temperatures are not lowered owing to their lower conversion efficiencies. Thin film microbridges suffer from low junction resistances and also from heating effects caused by d.c. bias supply and r.f. incident power. There seems to exist many problems to be overcome in order to make good submillimeter wave detectors by tunnel junctions or microbridges.Point contacts are now widely used as sensitive detectors for millimeter and submillimeter waves. Although there exist difficulties for making rugged and thermally cyclable point contacts, the techniques for making them have made considerable progress, and a new construction of detector mount has appeared, which brought a low noise mixer at 115GHz thermally cyclable.It is shown that the sensitivity of video detectors decreases as proportional to the inverse square of frequency. So, for submillimeter waves, video detectors are inferior to superconducting bolometers.Recent progress in heterodyne detectors (fundamental and harmonic mixers) are touched on. They are superior to Shottky diode mixers in that they have much smaller NEP's and much higher conversion efficiencies (especially in harmonic mixers), and also in that they operate with much smaller LO power. Experimental curves of IF output power v.s. bias voltage are given for harmonic mixers with harmonic number N=7 and N=10. It is noted that harmonic mixers with even harmonic number are preferable, because they can operate at zero bias voltage. Among them, low even numbers 2 or 4 are recommended in regards to good conversion efficiency.By using Josephson junctions, a peculiar parametric operation is possible, namely doubly degenerate mode. This mode operates under zero d.c. bias by choosing pump frequency as 2ωp=ωs+ωi, ωp-ωs-ωi. Zero bias operation allows the adoption of microbridge arrays. A parametric amplifier with 160 microbridge arrays was built at 33GHz, and showed amplifier gain of 15dB and noise temperature of 20K.
Superconductive electronics offers a unique combination of high bandwidth and low power for mission critical hardware such as digital processors at 20 to 100 GHz, microwatt per bit analog to digital converters, large digital switches at multi-Gb/s data rates, and low noise parametric amplifiers. This cryogenic technology, typically operating at a few degrees or a few tens of degrees Kelvin, depends upon the unique physics of superconducting materials such as Nb, NbN, and YBaCuO, and the fundamental circuit element, the Josephson junction (JJ) to create unique architectures of unprecedented design efficiency and performance. These circuits are based on the single flux quantum (SFQ) logic family, a technology that has no parallel in semiconductor electronics. Digital data is transmitted by voltage pulses with amplitude less than 1 mV, but at extremely high speeds. Individual gates have been operated as high as 370 GHz. In this paper, we present a brief overview of superconductive digital technology, describe some recent circuits, and discuss how the challenges to superconductive technology are being met, including the use of multi-chip module (MCM) technology, and the potential use of III-V HBT and HEMT circuits to provide interface drivers and amplifiers, possibly operated cryogenically.