Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

European Microwave Conference (EuMC)

Wide-Band, Ultra Low Noise MM-Wave Mixers with a Single Tuning Element

Antti V. Räisänen, Denis Crété, P. L. Richards, Frances L. Lloyd

Published Sep 1, 1986• 2 citations
Publisher

Abstract

Several SIS quasiparticle mixers have been designed and tested for the frequency range from 80 to 115 GHz. The sliding back short is the only adjustable RF-tuning element. The RF-filter reactance is used a s a fixed RF-matching element. A mixer which uses a single 2 × 2 μm2Pb-alloy junction in a 1/4-height waveguide mount has a coupled conversion gain of GM(DSB) = 2.6 ± 0.5 dB with an associated noise temperature of TM(DSB) = 16.4 ± 1.8 K at the best DSB operation point. The receiver noise temperature TR(DSB) is 27.5 ± 0.8 K for the test apparatus. This mixer provides a SSB receiver noise temperature below 50 K over the frequency range from 91 to 96 GHz, the minimum being TR(SSB) = 44 ± 4 K. Another mixer with an array of five 5 × 5 μm2junctions in series has much lower noise TM(DSB) = 6.6 ± 1.6 K, but less gain GM(DSB) = -5.1 ± 0.5 dB.

DOI
10.1109/euma.1986.334202

Related papers

Ultra-low-noise 100 GHz receiver based on parallel biased SIS arrays

S. V. Shitov, V. P. Koshelets, Sergey Kovtonyuk +3 more

The possibility of overcoming the main drawbacks of the traditional series arrays by using a parallel connection of SIS junctions for DC and IF current has been experimentally demonstrated in full height 70-116 GHz waveguide mixers. This new array concept has been successfully developed to: (i) avoid the influence of junction non-uniformity in the array; (ii) provide optimal matching at both RF input and IF output even in the case of high gain, and (iii) tune out junction capacitance without any DC blocks. The experimentally tested arrays contain 10 or 11 trilayer 2.5 mu m 2 Nb-AlO x -Nb junctions. Best values of T r (DSB) as low as 20+or-2 K have been measured at the receiver room temperature horn in the 104-108 GHz LO range with a 4 GHz IF and at a mixer ambient temperature of 4.5-5.5 K. An SSB mixer noise temperature as low as 6+or-3 K was estimated. This value is very close to the quantum noise limit hf/k approximately=5 K.

Superconductor Science and Technology•Sep 1, 1991•14 citations

Design and characterization of 225-370 GHz DSB and 247-360 GHz SSB full height waveguide SIS mixers

B. Lazareff, Dominique Billon-Pierron, A. Navarrini +1 more

\nWe report on the design and characterization of two full height waveguide SIS mixers for astronomical applications: a Double Side Band (DSB) fixed-tuned mixer covering the 225-370 GHz band ($\\approx$ 50% of relative bandwidth), and a tunable Single Side Band (SSB) mixer covering the 247-360 GHz frequency range. The DSB receiver noise temperature we have measured is below 50 K over a bandwidth larger than 100 GHz for the DSB mixer and has a minimum of 27 K (uncorrected) at 336 GHz; to our knowledge this is the lowest noise ever reported at this frequency. A receiver noise temperature below 80 K and an image band rejection around -14 dB were measured over most of the band of the SSB mixer.\nBoth mixers use similar chips that integrate a parallel tuning inductor with a radial microstrip stub to compensate for the junction capacitance of 75 fF (junction size 1 $\\mu$m$^2$). A stability criterion for intrinsically DSB and SSB mixers under typical operating conditions has been derived. The receiver designs have been optimised in order to guarantee a low mixer noise temperature while maintaining adequate gain and stable operation over the whole frequency bands of interest.\n

Journal de Physique IV (Proceedings)•May 1, 2002•5 citations

SIS mixers for low noise millimetre-wave heterodyne receivers

Steven R. Davies, C. T. Cunningham, Leslie T. Little

The development of ultra-low-noise receivers at frequencies of >200 GHz is primarily driven by astronomical applications. The most sensitive millimeter-wave receivers that have presently been constructed make use of the strong mixing afforded by superconductor-insulator-superconductor (SIS) tunnel junctions. In a collaborative project between UKC and RAL, a 230 GHz laboratory receiver has been built using a lead alloy SIS junction as the mixing element, mounted in 4:1 reduced-height waveguide, terminated at one end with a circular cross-section, adjustable backshort. Best results indicate a double-sideband receiver noise temperature of T/sub R/(DSB) approximately=120 K, which represents state-of-the-art performance at this frequency. Initial difficulties in achieving good mixing performance prompted an investigation into the importance of the 'quality' of mixer block backshort tuning elements. An analysis of the mixer equivalent circuit is presented which allows for loss in a non-ideal mixer block, and 3-port mixer model calculations are discussed which incorporate this analysis into the Tucker quantum theory of mixing.

•Mar 22, 1988•0 citations

MM wave quasioptical SIS mixers

Qing Hu, C. A. Mears, P. L. Richards +1 more

The authors have tested the performance of planar SIS (superconductor-insulator-superconductor) mixers with log-periodic antennas at near millimeter and submillimeter wave frequencies from 90 to 360 GHz. The large omega R/sub N/C product ( approximately 10 at 90 GHz) of the Nb/NbO/sub x//Pb-In-Au junctions requires an integrated inductive tuning element to resonate the junction capacitance at the operating frequencies. Two types of integrated tuning element were used which were designed with the aid of measurements using a Fourier transform spectrometer. Preliminary results indicate that the tuning elements can give very good mixer performance up to at least 200 GHz. An inductive wire in parallel with a 5-junction array gives a minimum mixer noise temperature of 115 K (DSB) at 90 GHz with a FWHM (full width at half maximum) bandwidth of 8 GHz. An open-ended microstrip stub in parallel with a single junction gives minimum mixer noise temperatures at 150 and 200 K (DSB) near 90 and 180 GHz with FWHM bandwidths of 4 and 3 GHz, respectively. The relatively high mixer noise temperatures compared to those of waveguide SIS mixers in a similar frequency range are attributed mainly to the losses in the optical system.>

IEEE Transactions on Magnetics•Mar 1, 1989•32 citations

A 100-GHz fixed-tuned waveguide SIS mixer exhibiting broad bandwidth and very low noise temperature

Sheng-Gai Shi, Takashi Noguchi, Junji Inatani

This paper presents design and performance data for a 100-GHz waveguide superconductor-insulator-superconductor (SIS) mixer, which is incorporated with a twin-junction device (i.e., two identical junctions connected in parallel through a tuning inductance) and a fixed-tuned broad-band waveguide mixer mount. The 100-GHz mixer is actually developed as a prototype of the 500-GHz one. The constructed 100-GHz SIS receiver results in an overall receiver noise temperature (DSB) of less than 40 K over the frequency range from 80-120 GHz, with a minimum value of just 20 K that is four times as large as the quantum limit (i.e., 4/spl planck//spl omega//k). Such a performance is comparable or even superior to those of the best mechanically tunable waveguide SIS receivers at the same frequency band. In addition, some interesting mixing behaviors related to this two-junction device are described in detail.

IEEE Transactions on Applied Superconductivity•Jan 1, 1997•22 citations

Parallel biased SIS-arrays for mm wave mixers: main ideas and experimental verification

An. B. Ermakov, V. P. Koshelets, Sergey Kovtonyuk +1 more

The possibility of overcoming the main drawbacks of the traditional series arrays by parallel connection of the SIS (superconductor-insulator-superconductor) junctions for DC and IF are demonstrated experimentally. The proposed mixing elements avoid the influence of the junction nonuniformity in the array, provide the optimal matching on both RF input and IF output, and tune out junction capacitance. Experimentally tested arrays contained up to eight high-quality Nb-AlO/sub x/-Nb junctions with R/sub n/=20-70 Omega at junction area 8/14 mu m/sup 2/. The best values of T/sub r/ (SSB) were measured to as low as 5 K on the mixer cold input flange in the 45-55-GHz bandwidth at an ambient temperature of 4.2 K. A mixer gain of up to 10 dB was obtained. The gain values were limited by bias stability at very high or even negative array output impedance. An experimental receiver noise temperature (SSB) of less than 20 K has been achieved.

IEEE Transactions on Magnetics•Mar 1, 1991•19 citations
Several SIS quasiparticle mixers have been designed and tested for the frequency range from 80 to 115 GHz. The sliding back short is the only adjustable RF-tuning element. The RF-filter reactance is used a s a fixed RF-matching element. A mixer which uses a single 2 × 2 μm2Pb-alloy junction in a 1/4-height waveguide mount has a coupled conversion gain of GM(DSB) = 2.6 ± 0.5 dB with an associated noise temperature of TM(DSB) = 16.4 ± 1.8 K at the best DSB operation point. The receiver noise temperature TR(DSB) is 27.5 ± 0.8 K for the test apparatus. This mixer provides a SSB receiver noise temperature below 50 K over the frequency range from 91 to 96 GHz, the minimum being TR(SSB) = 44 ± 4 K. Another mixer with an array of five 5 × 5 μm2junctions in series has much lower noise TM(DSB) = 6.6 ± 1.6 K, but less gain GM(DSB) = -5.1 ± 0.5 dB.
The possibility of overcoming the main drawbacks of the traditional series arrays by using a parallel connection of SIS junctions for DC and IF current has been experimentally demonstrated in full height 70-116 GHz waveguide mixers. This new array concept has been successfully developed to: (i) avoid the influence of junction non-uniformity in the array; (ii) provide optimal matching at both RF input and IF output even in the case of high gain, and (iii) tune out junction capacitance without any DC blocks. The experimentally tested arrays contain 10 or 11 trilayer 2.5 mu m 2 Nb-AlO x -Nb junctions. Best values of T r (DSB) as low as 20+or-2 K have been measured at the receiver room temperature horn in the 104-108 GHz LO range with a 4 GHz IF and at a mixer ambient temperature of 4.5-5.5 K. An SSB mixer noise temperature as low as 6+or-3 K was estimated. This value is very close to the quantum noise limit hf/k approximately=5 K.
\nWe report on the design and characterization of two full height waveguide SIS mixers for astronomical applications: a Double Side Band (DSB) fixed-tuned mixer covering the 225-370 GHz band (approx\\approxapprox 50% of relative bandwidth), and a tunable Single Side Band (SSB) mixer covering the 247-360 GHz frequency range. The DSB receiver noise temperature we have measured is below 50 K over a bandwidth larger than 100 GHz for the DSB mixer and has a minimum of 27 K (uncorrected) at 336 GHz; to our knowledge this is the lowest noise ever reported at this frequency. A receiver noise temperature below 80 K and an image band rejection around -14 dB were measured over most of the band of the SSB mixer.\nBoth mixers use similar chips that integrate a parallel tuning inductor with a radial microstrip stub to compensate for the junction capacitance of 75 fF (junction size 1 mu\\mumum2^22). A stability criterion for intrinsically DSB and SSB mixers under typical operating conditions has been derived. The receiver designs have been optimised in order to guarantee a low mixer noise temperature while maintaining adequate gain and stable operation over the whole frequency bands of interest.\n
The development of ultra-low-noise receivers at frequencies of >200 GHz is primarily driven by astronomical applications. The most sensitive millimeter-wave receivers that have presently been constructed make use of the strong mixing afforded by superconductor-insulator-superconductor (SIS) tunnel junctions. In a collaborative project between UKC and RAL, a 230 GHz laboratory receiver has been built using a lead alloy SIS junction as the mixing element, mounted in 4:1 reduced-height waveguide, terminated at one end with a circular cross-section, adjustable backshort. Best results indicate a double-sideband receiver noise temperature of T/sub R/(DSB) approximately=120 K, which represents state-of-the-art performance at this frequency. Initial difficulties in achieving good mixing performance prompted an investigation into the importance of the 'quality' of mixer block backshort tuning elements. An analysis of the mixer equivalent circuit is presented which allows for loss in a non-ideal mixer block, and 3-port mixer model calculations are discussed which incorporate this analysis into the Tucker quantum theory of mixing.
The authors have tested the performance of planar SIS (superconductor-insulator-superconductor) mixers with log-periodic antennas at near millimeter and submillimeter wave frequencies from 90 to 360 GHz. The large omega R/sub N/C product ( approximately 10 at 90 GHz) of the Nb/NbO/sub x//Pb-In-Au junctions requires an integrated inductive tuning element to resonate the junction capacitance at the operating frequencies. Two types of integrated tuning element were used which were designed with the aid of measurements using a Fourier transform spectrometer. Preliminary results indicate that the tuning elements can give very good mixer performance up to at least 200 GHz. An inductive wire in parallel with a 5-junction array gives a minimum mixer noise temperature of 115 K (DSB) at 90 GHz with a FWHM (full width at half maximum) bandwidth of 8 GHz. An open-ended microstrip stub in parallel with a single junction gives minimum mixer noise temperatures at 150 and 200 K (DSB) near 90 and 180 GHz with FWHM bandwidths of 4 and 3 GHz, respectively. The relatively high mixer noise temperatures compared to those of waveguide SIS mixers in a similar frequency range are attributed mainly to the losses in the optical system.>
This paper presents design and performance data for a 100-GHz waveguide superconductor-insulator-superconductor (SIS) mixer, which is incorporated with a twin-junction device (i.e., two identical junctions connected in parallel through a tuning inductance) and a fixed-tuned broad-band waveguide mixer mount. The 100-GHz mixer is actually developed as a prototype of the 500-GHz one. The constructed 100-GHz SIS receiver results in an overall receiver noise temperature (DSB) of less than 40 K over the frequency range from 80-120 GHz, with a minimum value of just 20 K that is four times as large as the quantum limit (i.e., 4/spl planck//spl omega//k). Such a performance is comparable or even superior to those of the best mechanically tunable waveguide SIS receivers at the same frequency band. In addition, some interesting mixing behaviors related to this two-junction device are described in detail.
The possibility of overcoming the main drawbacks of the traditional series arrays by parallel connection of the SIS (superconductor-insulator-superconductor) junctions for DC and IF are demonstrated experimentally. The proposed mixing elements avoid the influence of the junction nonuniformity in the array, provide the optimal matching on both RF input and IF output, and tune out junction capacitance. Experimentally tested arrays contained up to eight high-quality Nb-AlO/sub x/-Nb junctions with R/sub n/=20-70 Omega at junction area 8/14 mu m/sup 2/. The best values of T/sub r/ (SSB) were measured to as low as 5 K on the mixer cold input flange in the 45-55-GHz bandwidth at an ambient temperature of 4.2 K. A mixer gain of up to 10 dB was obtained. The gain values were limited by bias stability at very high or even negative array output impedance. An experimental receiver noise temperature (SSB) of less than 20 K has been achieved.