Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Applied Superconductivity

Operation of Low-$T_{c}$ Circuits in a Magnetic Environment

Romain Collot, Pascal Febvre, J. Kunert, H.‐G. Meyer

Published Dec 10, 2012• 15 citations
Publisher

Abstract

Low-Tcrapid single flux quantum (RSFQ) digital circuits without magnetic shielding fabricated with the FLUXONICS Foundry have been studied in the presence of external magnetic fields. Magnetic fields parallel to the plane of the chip are shown to influence more drastically the nominal behavior of the circuits above 5 μT, while perpendicular magnetic fields can reach 15 μT without affecting significantly their operation. This is confirmed by experimental SQUID interference patterns.

DOI
10.1109/tasc.2012.2233252

Related papers

Characterization of an On-Chip Magnetic Shielding Technique for Improving SFQ Circuit Performance

Romain Collot, Pascal Febvre, J. Kunert +3 more

An on-chip magnetic shielding technique was characterized on several DC-SQUIDs to prepare the next generation of complex digital RSFQ circuits designed by the FLUXONICS foundry. The maximal frequency of operation of a toggle flip-flop cell was used as a criteria to validate the concept. It goes from a simulated value of 52 GHz (46 ± 2 GHz experimentally), for a McCumber parameter βc= 1 with JC= 1 kA/cm2 in the absence of external magnetic field, down to 29 GHz in the presence of an external field of 88 μT. The shielding technique consists of surrounding a circuit by one or several superconducting niobium loops with the same layers as for the SFQ circuit. The loops are connected to the ground plane with vias. It is shown experimentally that the local magnetic field is reduced by a factor of 4 for the best shielded configuration, which limits the reduction of the maximal frequency of operation in presence of external magnetic field.

IEEE Transactions on Applied Superconductivity•Mar 15, 2016•6 citations

Magnetic modelling, analysis and on-chip shielding of SFQ Circuits

Rodwell S. Bakolo

ENGLISH ABSTRACT: Single Flux Quantum (SFQ) based electronic circuits are susceptible to failure if exposed to external magnetic fields, even in very small quantities. Operating margins of SFQ circuits have shown to decrease significantly in the presence of magnetic fields as small as 5 μT. This challenge makes SFQ circuits infeasible for the normal environment in which other technologies, such as CMOS, operate. Sources of magnetic fields include SFQ circuit’s own bias lines, the Earth, which can produce magnetic fields up to 65 μT and any other electromagnetic interference sources. Without protective measures, most SFQ circuits cannot work in the open environment. \nBy using the tools available in the inductance extraction tool, InductEx, a method for projecting uniform magnetic fields, of varying orientations on SFQ cells, strides have been made to make SFQ circuits more tolerant to magnetic fields. On-chip analysis of SFQ cells was done in the presence of magnetic fields from the x, y and z orientations. In addition, by varying currents in 3-D coils, the orientation of the magnetic fields can be varied. This way, it is now possible to analyse bias, parameter and operating field margins of SFQ cells in any direction of the magnetic field. \nTwo on-chip shielding solutions were analysed and developed. The conventional continuous superconductor \nlayer shield, dubbed the solid shield, and the grid shield. The grid shield resembles a Faraday \ncage and it is implemented by laying out bars of 2.5 μm width using the topmost layer in the Hypres0 \n4.5 kA/cm2 process. The solid shield is more effective against perpendicular (z-directed) magnetic fields \nthan against those in-plain (x and y-directed). In addition, the solid shield’s inclusion in SFQ cells results \nin the reduction of circuit inductance by up to 25 %. The grid shield is a very effective approach against \nin-plane magnetic fields. However, its effectiveness is inversely proportional to the spacing between grid \nbars. Compared to the solid shield, the grid shield has less effect on circuit inductance with a typical \nreduction of 8 % at a grid bar spacing of 5 μm. The large reduction in inductance can be overcome \nby making the inductors thinner and shorter. Shielding effectiveness of on-chip shields is enhanced by \nmaking ground contact vias from the shield layer to the ground plane. So far, uniformly grounded shields \nhave shown to be the most effective approach. \nThe solid shield improved the operating field margin of a DFF cell against a z-directed magnetic field \nfrom 30 μT to 531 μT, while the grid shield, of 5 μm grid spacing, improved the margins from 68 μT \nto 290 μT against an x-directed magnetic field. In the DC-SFQ cell, the operating field margin was \nimproved with a solid shield from 47 μT to 464 μT, against a z-directed magnetic field, while with a \ngrid shield, the improvement was from 211 μT to 381 μT, against an x-directed fields. \nTo further enhance the magnetic field tolerance of SFQ circuits, design tenets that target specific components, \nsuch as inductors, were analysed. Thin and narrow inductors have shown less coupling to \nexternal magnetic fields. In addition, moats have shown to influence OFM results depending on the \norientation of magnetic fields. \nThis work has delivered design and analysis methods for magnetic field tolerant SFQ circuits.

•Mar 1, 2018•0 citations

Influence of external magnetic fields on the inductive properties of rapid single-flux-quantum digital circuits

Romain Collot, Pascal Febvre, Jean-Luc Issler +5 more

A method has been developped to take into account the presence of a local external magnetic field in Superconducting Quantum Interference Devices (SQUIDs) loops composing Rapid Single-Flux-Quantum (RSFQ) circuits, through modifications of circuit inductances. A good agreement is observed between analytical formulas and simulations performed by time-domain softwares. The agreement with the first experiments is still only qualitative at this stage.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2013•3 citations

[INVITED] Digital magnetometers based on the Single-Flux-Quantum technique

Pascal Febvre, Stolz, Ronny, Meyer, Hans-Georg +5 more

Superconducting Quantum Interference Devices (SQUIDs) are known to be the most sensitive magnetometers. We present a new type of low-Tc digital SQUID that is based on Rapid-Single-Flux-Quantum (RSFQ) Logic. It allows the on-chip conversion of the detected magnetic field into a digital form, suitable for noiseless processing, very high dynamic range and high slew rate. The sensitivity, limited to one magnetic single flux quantum, and a dynamic range of 76 dB, that corresponds to an upper limit of the magnetic field amplitude higher than 5 μT, have been measured along with overnight stability. First signatures of magnetic fields have been observed simultaneously with the ones of analogue SQUIDs in the ultra low noise environment of the Laboratoire Souterrain à Bas Bruit (LSBB) located in Rustrel, Provence, France.

•Jun 15, 2009•0 citations

Investigation of the flux state in single-flux-quantum circuits with moats by scanning SQUID microscope

Koji A. O. Suzuki, Hiroki Kawamura, Michitaka Maruyama +10 more

We have investigated the flux state in high- and low- T c SFQ circuits having superconducting ground planes with moats by a scanning SQUID microscope (SSM) system. Observation of YBa 2 Cu 3 O y (YBCO) sampler circuits having superconducting ground planes with 5 µm-wide moats confirmed that magnetic flux was excluded from the moat-surrounded area including ramp-edge Josephson junctions. The threshold value for complete flux exclusion was about 0.8 µT slightly depending on chips, which can be achieved readily with dual μ-metal magnetic shielding. Moreover, we have observed the flux state in Nb multilayer structures having a superconducting ground plane with 4 µm wide moats, which was designed and fabricated using the CONNECT cell library. It was confirmed that magnetic flux was trapped selectively into moats with appropriate configuration, which were fabricated within each 40 µm × 40 µm unit cell.

Superconductor Science and Technology•Mar 16, 2006•5 citations

The influence of the ground current on large-scale single-flux-quantum circuits

K. Fujiwara, T Hikida, Nobuyuki Yoshikawa +3 more

In this study we have investigated the influence of an externally applied ground current on large-scale single-flux-quantum (SFQ) circuits. A Josephson transmission line containing 10 4 junctions with a total bias current of 1.8 A was examined for this purpose. The test results show that the ground current affects the circuit operation remarkably strongly. In the worst case, the ground current of about 10 mA for a 5 mm die chip disturbs the circuit operation. The results also show that DC/SFQ and SFQ/DC converters are very sensitive to the ground current. To eliminate the effect of the ground current, we have made SFQ circuits completely shielded from the external magnetic field by using upper and lower ground planes. It was found that the shielded SFQ circuits are much less sensitive to the ground current. These results show that the magnetic shielding structure is one solution for reducing the effects of the ground current and hence the external magnetic field.

Superconductor Science and Technology•Mar 16, 2006•11 citations
Operation of Low-TcT_{c}Tc​ Circuits in a Magnetic Environment
Low-Tcrapid single flux quantum (RSFQ) digital circuits without magnetic shielding fabricated with the FLUXONICS Foundry have been studied in the presence of external magnetic fields. Magnetic fields parallel to the plane of the chip are shown to influence more drastically the nominal behavior of the circuits above 5 μT, while perpendicular magnetic fields can reach 15 μT without affecting significantly their operation. This is confirmed by experimental SQUID interference patterns.
An on-chip magnetic shielding technique was characterized on several DC-SQUIDs to prepare the next generation of complex digital RSFQ circuits designed by the FLUXONICS foundry. The maximal frequency of operation of a toggle flip-flop cell was used as a criteria to validate the concept. It goes from a simulated value of 52 GHz (46 ± 2 GHz experimentally), for a McCumber parameter βc= 1 with JC= 1 kA/cm2 in the absence of external magnetic field, down to 29 GHz in the presence of an external field of 88 μT. The shielding technique consists of surrounding a circuit by one or several superconducting niobium loops with the same layers as for the SFQ circuit. The loops are connected to the ground plane with vias. It is shown experimentally that the local magnetic field is reduced by a factor of 4 for the best shielded configuration, which limits the reduction of the maximal frequency of operation in presence of external magnetic field.
ENGLISH ABSTRACT: Single Flux Quantum (SFQ) based electronic circuits are susceptible to failure if exposed to external magnetic fields, even in very small quantities. Operating margins of SFQ circuits have shown to decrease significantly in the presence of magnetic fields as small as 5 μT. This challenge makes SFQ circuits infeasible for the normal environment in which other technologies, such as CMOS, operate. Sources of magnetic fields include SFQ circuit’s own bias lines, the Earth, which can produce magnetic fields up to 65 μT and any other electromagnetic interference sources. Without protective measures, most SFQ circuits cannot work in the open environment. \nBy using the tools available in the inductance extraction tool, InductEx, a method for projecting uniform magnetic fields, of varying orientations on SFQ cells, strides have been made to make SFQ circuits more tolerant to magnetic fields. On-chip analysis of SFQ cells was done in the presence of magnetic fields from the x, y and z orientations. In addition, by varying currents in 3-D coils, the orientation of the magnetic fields can be varied. This way, it is now possible to analyse bias, parameter and operating field margins of SFQ cells in any direction of the magnetic field. \nTwo on-chip shielding solutions were analysed and developed. The conventional continuous superconductor \nlayer shield, dubbed the solid shield, and the grid shield. The grid shield resembles a Faraday \ncage and it is implemented by laying out bars of 2.5 μm width using the topmost layer in the Hypres0 \n4.5 kA/cm2 process. The solid shield is more effective against perpendicular (z-directed) magnetic fields \nthan against those in-plain (x and y-directed). In addition, the solid shield’s inclusion in SFQ cells results \nin the reduction of circuit inductance by up to 25 %. The grid shield is a very effective approach against \nin-plane magnetic fields. However, its effectiveness is inversely proportional to the spacing between grid \nbars. Compared to the solid shield, the grid shield has less effect on circuit inductance with a typical \nreduction of 8 % at a grid bar spacing of 5 μm. The large reduction in inductance can be overcome \nby making the inductors thinner and shorter. Shielding effectiveness of on-chip shields is enhanced by \nmaking ground contact vias from the shield layer to the ground plane. So far, uniformly grounded shields \nhave shown to be the most effective approach. \nThe solid shield improved the operating field margin of a DFF cell against a z-directed magnetic field \nfrom 30 μT to 531 μT, while the grid shield, of 5 μm grid spacing, improved the margins from 68 μT \nto 290 μT against an x-directed magnetic field. In the DC-SFQ cell, the operating field margin was \nimproved with a solid shield from 47 μT to 464 μT, against a z-directed magnetic field, while with a \ngrid shield, the improvement was from 211 μT to 381 μT, against an x-directed fields. \nTo further enhance the magnetic field tolerance of SFQ circuits, design tenets that target specific components, \nsuch as inductors, were analysed. Thin and narrow inductors have shown less coupling to \nexternal magnetic fields. In addition, moats have shown to influence OFM results depending on the \norientation of magnetic fields. \nThis work has delivered design and analysis methods for magnetic field tolerant SFQ circuits.
Superconducting Quantum Interference Devices (SQUIDs) are known to be the most sensitive magnetometers. We present a new type of low-Tc digital SQUID that is based on Rapid-Single-Flux-Quantum (RSFQ) Logic. It allows the on-chip conversion of the detected magnetic field into a digital form, suitable for noiseless processing, very high dynamic range and high slew rate. The sensitivity, limited to one magnetic single flux quantum, and a dynamic range of 76 dB, that corresponds to an upper limit of the magnetic field amplitude higher than 5 μT, have been measured along with overnight stability. First signatures of magnetic fields have been observed simultaneously with the ones of analogue SQUIDs in the ultra low noise environment of the Laboratoire Souterrain à Bas Bruit (LSBB) located in Rustrel, Provence, France.
We have investigated the flux state in high- and low- T c SFQ circuits having superconducting ground planes with moats by a scanning SQUID microscope (SSM) system. Observation of YBa 2 Cu 3 O y (YBCO) sampler circuits having superconducting ground planes with 5 µm-wide moats confirmed that magnetic flux was excluded from the moat-surrounded area including ramp-edge Josephson junctions. The threshold value for complete flux exclusion was about 0.8 µT slightly depending on chips, which can be achieved readily with dual μ-metal magnetic shielding. Moreover, we have observed the flux state in Nb multilayer structures having a superconducting ground plane with 4 µm wide moats, which was designed and fabricated using the CONNECT cell library. It was confirmed that magnetic flux was trapped selectively into moats with appropriate configuration, which were fabricated within each 40 µm × 40 µm unit cell.
In this study we have investigated the influence of an externally applied ground current on large-scale single-flux-quantum (SFQ) circuits. A Josephson transmission line containing 10 4 junctions with a total bias current of 1.8 A was examined for this purpose. The test results show that the ground current affects the circuit operation remarkably strongly. In the worst case, the ground current of about 10 mA for a 5 mm die chip disturbs the circuit operation. The results also show that DC/SFQ and SFQ/DC converters are very sensitive to the ground current. To eliminate the effect of the ground current, we have made SFQ circuits completely shielded from the external magnetic field by using upper and lower ground planes. It was found that the shielded SFQ circuits are much less sensitive to the ground current. These results show that the magnetic shielding structure is one solution for reducing the effects of the ground current and hence the external magnetic field.