In this study we have investigated the influence of an externally applied ground current on large-scale single-flux-quantum (SFQ) circuits. A Josephson transmission line containing 10 4 junctions with a total bias current of 1.8 A was examined for this purpose. The test results show that the ground current affects the circuit operation remarkably strongly. In the worst case, the ground current of about 10 mA for a 5 mm die chip disturbs the circuit operation. The results also show that DC/SFQ and SFQ/DC converters are very sensitive to the ground current. To eliminate the effect of the ground current, we have made SFQ circuits completely shielded from the external magnetic field by using upper and lower ground planes. It was found that the shielded SFQ circuits are much less sensitive to the ground current. These results show that the magnetic shielding structure is one solution for reducing the effects of the ground current and hence the external magnetic field.
In this study we have investigated the influence of an externally applied ground current on large-scale single-flux-quantum (SFQ) circuits. A Josephson transmission line containing 10 4 junctions with a total bias current of 1.8 A was examined for this purpose. The test results show that the ground current affects the circuit operation remarkably strongly. In the worst case, the ground current of about 10 mA for a 5 mm die chip disturbs the circuit operation. The results also show that DC/SFQ and SFQ/DC converters are very sensitive to the ground current. To eliminate the effect of the ground current, we have made SFQ circuits completely shielded from the external magnetic field by using upper and lower ground planes. It was found that the shielded SFQ circuits are much less sensitive to the ground current. These results show that the magnetic shielding structure is one solution for reducing the effects of the ground current and hence the external magnetic field.
The supply of bias current is one of the key problems to be overcome for fully operational large-scale SFQ circuits. Large currents cause various undesirable effects that degrade circuit operation. The magnetic field induced by a large DC bias current affects the operation of several SFQ cells, even with a microstrip-line structure applied for the bias lines. In this paper, experimental results using SQUIDs show that bias-line shielding is the most effective way to reduce the effect of the DC bias current. The operating margins of SFQ cells were also found to be sensitive to the current in the ground plane. The location of a ground bonding should be close to the point of current injection if we wish to avoid undesirable diffusion of current through the ground plane. We confirmed the effectiveness of bias-line shielding and of the location of ground bonding with a circuit composed of about 500 junctions.
Large-scale SFQ integrated circuits require a large amount of dc-bias current. The magnetic fields induced by the dc-bias currents and the return currents flowing in a ground plane have a great influence on the performance of SFQ circuits. As an approach to reduce the influence, the dc-power (DCP) layer placed under a ground plane is newly introduced in SRL advanced Nb process. We have experimentally evaluated the effects of the DCP layer using SQUIDs and large-scale Josephson transmission line (JTL) circuits with more than 10,000 junctions. The SQUIDs showed that there was small magnetic flux coupling between the DCP lines and themselves and that the coupled flux was enhanced by the return current. The coupled flux decreased with increasing line width of the DCP lines and with increasing distance from the centerlines of them. In the large-scale JTL tests, the cells with DCP patterns showed wider operating margins than the CONNECT OPEN cells with partial magnetic shielding of bias current lines. The test results also showed that a line shape along the periphery of a cell was more effective than a plane shape within a cell as a DCP layer pattern for bias current feeds.
We have investigated the effect of a dc-power (DCP) layer on the performance of single flux quantum (SFQ) circuits by changing the film thickness of a ground plane (GP). The DCP layer was placed below the GP and was used as bias current feeds. Two measurements were conducted. One was direct detection of the magnetic flux above the GP by using SQUIDs. The results indicated that the GPs with film thicknesses of more than 400 nm were effective to completely suppress the flux under the condition that the return current was extracted from the ground plane. The other was evaluation of the operating margins of the 408 bit shift register circuits (SRs) with 8032 Josephson junctions and a total designed bias current of 1.05 A. The results showed that a 500 nm thick GP had an advantage over a 300 nm thick GP in the dependence of the upper margin on the bias current port of the SR.
ENGLISH ABSTRACT: Single Flux Quantum (SFQ) based electronic circuits are susceptible to failure if exposed to external magnetic fields, even in very small quantities. Operating margins of SFQ circuits have shown to decrease significantly in the presence of magnetic fields as small as 5 μT. This challenge makes SFQ circuits infeasible for the normal environment in which other technologies, such as CMOS, operate. Sources of magnetic fields include SFQ circuit’s own bias lines, the Earth, which can produce magnetic fields up to 65 μT and any other electromagnetic interference sources. Without protective measures, most SFQ circuits cannot work in the open environment. \nBy using the tools available in the inductance extraction tool, InductEx, a method for projecting uniform magnetic fields, of varying orientations on SFQ cells, strides have been made to make SFQ circuits more tolerant to magnetic fields. On-chip analysis of SFQ cells was done in the presence of magnetic fields from the x, y and z orientations. In addition, by varying currents in 3-D coils, the orientation of the magnetic fields can be varied. This way, it is now possible to analyse bias, parameter and operating field margins of SFQ cells in any direction of the magnetic field. \nTwo on-chip shielding solutions were analysed and developed. The conventional continuous superconductor \nlayer shield, dubbed the solid shield, and the grid shield. The grid shield resembles a Faraday \ncage and it is implemented by laying out bars of 2.5 μm width using the topmost layer in the Hypres0 \n4.5 kA/cm2 process. The solid shield is more effective against perpendicular (z-directed) magnetic fields \nthan against those in-plain (x and y-directed). In addition, the solid shield’s inclusion in SFQ cells results \nin the reduction of circuit inductance by up to 25 %. The grid shield is a very effective approach against \nin-plane magnetic fields. However, its effectiveness is inversely proportional to the spacing between grid \nbars. Compared to the solid shield, the grid shield has less effect on circuit inductance with a typical \nreduction of 8 % at a grid bar spacing of 5 μm. The large reduction in inductance can be overcome \nby making the inductors thinner and shorter. Shielding effectiveness of on-chip shields is enhanced by \nmaking ground contact vias from the shield layer to the ground plane. So far, uniformly grounded shields \nhave shown to be the most effective approach. \nThe solid shield improved the operating field margin of a DFF cell against a z-directed magnetic field \nfrom 30 μT to 531 μT, while the grid shield, of 5 μm grid spacing, improved the margins from 68 μT \nto 290 μT against an x-directed magnetic field. In the DC-SFQ cell, the operating field margin was \nimproved with a solid shield from 47 μT to 464 μT, against a z-directed magnetic field, while with a \ngrid shield, the improvement was from 211 μT to 381 μT, against an x-directed fields. \nTo further enhance the magnetic field tolerance of SFQ circuits, design tenets that target specific components, \nsuch as inductors, were analysed. Thin and narrow inductors have shown less coupling to \nexternal magnetic fields. In addition, moats have shown to influence OFM results depending on the \norientation of magnetic fields. \nThis work has delivered design and analysis methods for magnetic field tolerant SFQ circuits.
An increase in bias currents supplied to single-flux-quantum (SFQ) circuits is a rising problem in building large-scale integrated SFQ circuits, because the magnetic fields generated by bias currents and ground return currents affect the circuit operation. Current recycling technique, which can drastically reduce the total bias current of SFQ circuits, is expected to be a very effective solution for large-scale SFQ circuits. To realize the current recycling technique, signal transmission between SFQ logic circuits located on different ground planes is required. Two types of inductively coupled pulse transfer circuits were examined in this study. One is composed of a simple JTL driver and a DC-SQUID receiver whose junctions are slightly under-damped to enhance the magnetic sensitivity of the SQUID. The other circuit is composed of an SFQ driver based on a delay flip-flop (DFF) and a SQUID receiver. The advantage of the DFF-based circuit is that the coupling time between the driver and the receiver can be increased to ensure appropriate switching in the receiver junction. Two types of transfer circuits were implemented using the SRL 2.5 kA/cm2Nb process and their correct operation was experimentally confirmed. Circuit structures for effective coupling of the SFQ pulse transfer were also investigated. It was shown that a ground plane boundary should be separated from a ground plane hole underneath coupling inductors to obtain high coupling factors.
The practical implementation of RSFQ technology in most digital electronics application areas requires much more complexity than the presently developed circuits. There are two important issues in building large-scale RSFQ circuits: 1) the recycling of the bias currents and 2) the transfer of SFQ pulses between circuits located far apart. RSFQ circuits are well known to operate with DC current bias. Even though the DC current biasing is more forgiving than the problematic AC biasing, it can still be a big concern when the circuit size becomes large. Dramatic reduction of the total bias current can be achieved by biasing several RSFQ circuits in series, where each circuit is positioned on a separate ground plane. In this work, we have used magnetically coupled Josephson transmission lines as inputs and outputs of an isolated shift register to show the feasibility of using the concept of serial biasing in current recycling. The circuit was simulated, fabricated with Nb technology, and tested at a temperature of 4.2 K. Test results show that SFQ pulses were transferred into the shift register built on a separate ground plane, clocked through it, and sent out back to the circuit on the original ground plane. We also studied on how to transfer SFQ pulses over an extended length, an important issue in building large RSFQ circuits. We have designed the circuits to test our microstrip line and multichip module approaches. We designed, optimized, fabricated and tested the circuits. Test results show that SFQ pulses can be successfully transmitted over an extensive distance in a chip and between chips.