Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Asia-Pacific Microwave Conference (APMC)

A 220 GHz low noise superconducting receiver with wide instantaneous operating bandwidth

Chih-Chiang Han, Ming-Jye Wang, Tse-Jun Chen, Wei-Chun Lu, Edward Tong

Published Dec 1, 2012• 1 citation
Publisher

Abstract

A 220 GHz mixer chip based on a 3-junction series distributed superconducting mixer has been developed. This mixer employs a design, which minimizes the output capacitances, such that it can offer a wide instantaneous bandwidth of up to 12 GHz. We have incorporated this mixer into a receiver package and a dedicated automatic test bench has been developed to characterize its performance. The receiver demonstrates ultra low noise temperature, as low as 32 K, or 3 hν/k. The measured noise temperature remains below 50 K beyond 10 GHz IF.

DOI
10.1109/apmc.2012.6421620

Related papers

Design and Performance of a 3-Junction Series Distributed SIS Mixer for Wide IF Applications

Edward Tong, Paul Grimes, A. Barbier +2 more

Series distributed superconductor-insulator-superconductor mixers have been used to provide very wide instantaneous bandwidth of operation. In this paper, we explore a design based on a 3-junction array in which the junctions themselves form part of the RF tuning network of the mixer. We have developed mixers based on these designs for use in the 200 and 300 GHz bands. Receivers incorporating these wideband mixers demonstrate very low noise temperature. At a local oscillator frequency of 300 GHz, the lowest measured intermediate frequency noise temperature is about 42 K and the usable intermediate frequency bandwidth extends from 6 to 16.5 GHz. Both the design theory and experimental results are presented.

IEEE Transactions on Applied Superconductivity•Dec 20, 2012•12 citations

A Distributed Lumped-Element SIS Mixer With Very Wide Instantaneous Bandwidth

Edward Tong, R. Blundell, Koko G. Megerian +3 more

A novel type of distributed superconducting mixer with very low output capacitance has been designed for a 330-420 GHz waveguide mixer. In this design, a pair of lumped element Superconductor-Insulator-Superconductor junctions is connected in series to form the unit cell of a composite transmission line. The mixer utilizes two cascaded cells. Using an intermediate frequency (IF) of 5 GHz, we have measured Double-side-band (DSB) receiver noise temperatures of 90-120 K between 360 and 410 GHz. This mixer design offers very wide instantaneous bandwidth. The measured IF bandwidth is in excess of 18 GHz. At a Local Oscillator frequency of 384 GHz, the Y-factor measured at an IF frequency of 18 GHz is 2.1, compared to a Y-factor of 2.2 measured at an IF of 5 GHz. The mixer also has a high dynamic range. The 1-dB input compression point is only reached with an input black body load of 30,000 K.

IEEE Transactions on Applied Superconductivity•Jun 1, 2005•18 citations

Wide If 230-GHz Superconductor-Insulator-Superconductor Mixer

Naeun Shin, Jung‐Won Lee, Ming-Jye Wang

A 230 GHz Superconductor-Insulator-Superconductor (SIS) mixer is designed focusing on a good performance in the IF frequency range of 4–16 GHz over the RF band from 211 to 275 GHz. A transition from a full-height waveguide to a probe is designed using HFSS. The mixer chips containing SIS junctions are designed and optimized to have low total capacitance of circuits to ensure wide IF bandwidth. The chip fabrication was done in Academia Sinica Institute of Astronomy and Astrophysics (ASIAA), where the masks were conducted by TSMC. A lab test was conducted on a superconducting mixer with a cryogenic dewar. The gap voltage in the I-V curve of the mixer is approximately 8 mV, and there is a clear nonlinearity around a current of 110 μA, which matches well with the simulation. The receiver noise temperature is approximately 60 K including optical losses and the noise from the RF input.

International Conference on Information and Communication Technology Convergence (ICTC)•Oct 16, 2024•1 citation

A 220 GHz finline mixer with ultra-wide instantaneous bandwidth

BK Tan, Faouzi M. Boussaha, Christine Chaumont +1 more

We describe the design and fabrication of a 220 GHz superconductor-insulator-superconductor (SIS) mixer with ultrawide IF bandwidth. The mixer is fabricated on a 100 µm thick quartz substrate, with planar circuit on-chip integration. The RF power is coupled to the tunnel junction via a unilateral finline taper and a slotline-to-microstrip transition. We used a double-stub tuning network to tune out the junction’s parasitic capacitance at a broad RF bandwidth, and matched the output impedance of the mixer to the input impedance of the IF amplifier (50 Ω) from 4–18 GHz using a 6-stage IF impedance-transformer. We have fabricated these devices and have measured good DC current-voltage (IV) characteristic curves. The heterodyne mixing performance of these devices is currently being measured, and we expect to present the results in the forthcoming ISSTT conference in March.

ORA review team•Jan 1, 2015•7 citations

Ultra-low-noise 100 GHz receiver based on parallel biased SIS arrays

S. V. Shitov, V. P. Koshelets, Sergey Kovtonyuk +3 more

The possibility of overcoming the main drawbacks of the traditional series arrays by using a parallel connection of SIS junctions for DC and IF current has been experimentally demonstrated in full height 70-116 GHz waveguide mixers. This new array concept has been successfully developed to: (i) avoid the influence of junction non-uniformity in the array; (ii) provide optimal matching at both RF input and IF output even in the case of high gain, and (iii) tune out junction capacitance without any DC blocks. The experimentally tested arrays contain 10 or 11 trilayer 2.5 mu m 2 Nb-AlO x -Nb junctions. Best values of T r (DSB) as low as 20+or-2 K have been measured at the receiver room temperature horn in the 104-108 GHz LO range with a 4 GHz IF and at a mixer ambient temperature of 4.5-5.5 K. An SSB mixer noise temperature as low as 6+or-3 K was estimated. This value is very close to the quantum noise limit hf/k approximately=5 K.

Superconductor Science and Technology•Sep 1, 1991•14 citations

Design, fabrication, and experimental characterization of a 300-GHz-band SIS mixer prototype for the BHEX mission

Yosuke Murayama, Edward Tong, Takafumi Kojima +8 more

We report the design, fabrication, and experimental characterization of a 300-GHz-band superconductor-insulator-superconductor (SIS) mixer prototype for the Black Hole Explorer (BHEX) mission. The mixer employs a three-junction series SIS array, a waveguide probe with a microstrip impedance transformer, and an on-chip IF tuning circuit. As a first implementation of the baseline RF design, the mixer chip was fabricated using an established aluminum-oxide-barrier SIS junction process. Test junctions on the same wafer showed a critical current density of approximately 12 kA/cm2. The fabricated mixer chip was mounted in a waveguide mixer block and evaluated at a mixer-block temperature of 4 K by the Y-factor method. The measured double-sideband receiver noise temperature was 26–41 K at LO frequencies of 240–307 GHz. At 285 GHz, a noise temperature of approximately 30 K was obtained over the 4–9 GHz IF band, close to the two-photon sensitivity target adopted for the BHEX SIS receiver. These results demonstrate low-noise operation of the first prototype and provide feedback for improving RF/IF bandwidth and mixer stability in subsequent designs.

IEEE Transactions on Terahertz Science and Technology•Jan 1, 2026•0 citations
A 220 GHz mixer chip based on a 3-junction series distributed superconducting mixer has been developed. This mixer employs a design, which minimizes the output capacitances, such that it can offer a wide instantaneous bandwidth of up to 12 GHz. We have incorporated this mixer into a receiver package and a dedicated automatic test bench has been developed to characterize its performance. The receiver demonstrates ultra low noise temperature, as low as 32 K, or 3 hν/k. The measured noise temperature remains below 50 K beyond 10 GHz IF.
Series distributed superconductor-insulator-superconductor mixers have been used to provide very wide instantaneous bandwidth of operation. In this paper, we explore a design based on a 3-junction array in which the junctions themselves form part of the RF tuning network of the mixer. We have developed mixers based on these designs for use in the 200 and 300 GHz bands. Receivers incorporating these wideband mixers demonstrate very low noise temperature. At a local oscillator frequency of 300 GHz, the lowest measured intermediate frequency noise temperature is about 42 K and the usable intermediate frequency bandwidth extends from 6 to 16.5 GHz. Both the design theory and experimental results are presented.
A novel type of distributed superconducting mixer with very low output capacitance has been designed for a 330-420 GHz waveguide mixer. In this design, a pair of lumped element Superconductor-Insulator-Superconductor junctions is connected in series to form the unit cell of a composite transmission line. The mixer utilizes two cascaded cells. Using an intermediate frequency (IF) of 5 GHz, we have measured Double-side-band (DSB) receiver noise temperatures of 90-120 K between 360 and 410 GHz. This mixer design offers very wide instantaneous bandwidth. The measured IF bandwidth is in excess of 18 GHz. At a Local Oscillator frequency of 384 GHz, the Y-factor measured at an IF frequency of 18 GHz is 2.1, compared to a Y-factor of 2.2 measured at an IF of 5 GHz. The mixer also has a high dynamic range. The 1-dB input compression point is only reached with an input black body load of 30,000 K.
A 230 GHz Superconductor-Insulator-Superconductor (SIS) mixer is designed focusing on a good performance in the IF frequency range of 4–16 GHz over the RF band from 211 to 275 GHz. A transition from a full-height waveguide to a probe is designed using HFSS. The mixer chips containing SIS junctions are designed and optimized to have low total capacitance of circuits to ensure wide IF bandwidth. The chip fabrication was done in Academia Sinica Institute of Astronomy and Astrophysics (ASIAA), where the masks were conducted by TSMC. A lab test was conducted on a superconducting mixer with a cryogenic dewar. The gap voltage in the I-V curve of the mixer is approximately 8 mV, and there is a clear nonlinearity around a current of 110 μA, which matches well with the simulation. The receiver noise temperature is approximately 60 K including optical losses and the noise from the RF input.
We describe the design and fabrication of a 220 GHz superconductor-insulator-superconductor (SIS) mixer with ultrawide IF bandwidth. The mixer is fabricated on a 100 µm thick quartz substrate, with planar circuit on-chip integration. The RF power is coupled to the tunnel junction via a unilateral finline taper and a slotline-to-microstrip transition. We used a double-stub tuning network to tune out the junction’s parasitic capacitance at a broad RF bandwidth, and matched the output impedance of the mixer to the input impedance of the IF amplifier (50 Ω) from 4–18 GHz using a 6-stage IF impedance-transformer. We have fabricated these devices and have measured good DC current-voltage (IV) characteristic curves. The heterodyne mixing performance of these devices is currently being measured, and we expect to present the results in the forthcoming ISSTT conference in March.
The possibility of overcoming the main drawbacks of the traditional series arrays by using a parallel connection of SIS junctions for DC and IF current has been experimentally demonstrated in full height 70-116 GHz waveguide mixers. This new array concept has been successfully developed to: (i) avoid the influence of junction non-uniformity in the array; (ii) provide optimal matching at both RF input and IF output even in the case of high gain, and (iii) tune out junction capacitance without any DC blocks. The experimentally tested arrays contain 10 or 11 trilayer 2.5 mu m 2 Nb-AlO x -Nb junctions. Best values of T r (DSB) as low as 20+or-2 K have been measured at the receiver room temperature horn in the 104-108 GHz LO range with a 4 GHz IF and at a mixer ambient temperature of 4.5-5.5 K. An SSB mixer noise temperature as low as 6+or-3 K was estimated. This value is very close to the quantum noise limit hf/k approximately=5 K.
We report the design, fabrication, and experimental characterization of a 300-GHz-band superconductor-insulator-superconductor (SIS) mixer prototype for the Black Hole Explorer (BHEX) mission. The mixer employs a three-junction series SIS array, a waveguide probe with a microstrip impedance transformer, and an on-chip IF tuning circuit. As a first implementation of the baseline RF design, the mixer chip was fabricated using an established aluminum-oxide-barrier SIS junction process. Test junctions on the same wafer showed a critical current density of approximately 12 kA/cm2. The fabricated mixer chip was mounted in a waveguide mixer block and evaluated at a mixer-block temperature of 4 K by the Y-factor method. The measured double-sideband receiver noise temperature was 26–41 K at LO frequencies of 240–307 GHz. At 285 GHz, a noise temperature of approximately 30 K was obtained over the 4–9 GHz IF band, close to the two-photon sensitivity target adopted for the BHEX SIS receiver. These results demonstrate low-noise operation of the first prototype and provide feedback for improving RF/IF bandwidth and mixer stability in subsequent designs.