Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Science Diliman

Characterization of the Magneto-Optical Trap for Rb Atoms

J. W. F. Liwag, Joseph Manyaga, Marlon Patiño, Marc Ravacio, K. Karremans

Published Jul 4, 2012• 1 citation
OpenAlex

Abstract

A magneto-optical trap (MOT) for rubidium (Rb) atoms has been in operation at the University of San Carlos Optoelectronics Research Laboratory in Cebu City since 1998. The experimental design for this MOT is based on the system described by Wieman et al. (1995). This system formed the backbone of the research which resulted in the first observation of Bose-Einstein condensation (BEC) by the same group in 1995. An essential step for realizing this remarkable result was the accuracy in the timing mechanism of the experiment. To obtain an MOT in which we can switch the laser and magnetic fields with sub-millisecond accuracy, we have put considerable efforts to realize a computer-controlled system. Previous measurements have been used to validate our new results. The realization of a fast switch for the trapping laser creates the opportunity to measure time-of-flight (TOF) signals. These ballistic measurements can be used to infer the temperature of the cloud of trapped atoms. We hope to continue working on this automated system of the MOT towards BEC as a long-term goal of our research group.

Related papers

Introduction of advanced photonics research at the undergraduate level: an example from the Philippines

J. W. F. Liwag, Kees Karremans

Laser cooling experiments are a good example of how the interaction between light and matter can be applied to manipulate neutral atoms. At the University of San Carlos we have constructed a magneto-optical trap (MOT) for rubidium (Rb) atoms. The setup is based on the design of the MOT Wieman et al used in their efforts to reach Bose-Einstein condensation. The use of diode lasers enables the introduction of these advanced experiments at undergraduate level. Since 1998, when the MOT became operational at USC, a great number of undergraduate students have done the experiment. Not only did they learn the basics of cooling and trapping, they also gained experience in operating lasers properly, vacuum technology, and techniques for frequency stabilization. In some cases students opted to perform spectroscopy experiments on Rb atoms, which could easily be done using this setup. Of course, the presence of the MOT also gave a great boost to the research in optoelectronics, a new research direction in our department. Characterizing the MOT has resulted in several scientific papers in local physics journals as well as presentations to the annual Philippine Physics Congress. The next step is towards the realization of Bose-Einstein condensation of Rb in our Optoelectronics Laboratory.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•May 28, 2002•0 citations

Constucting a Magneto-optical Trap (MOT) as a means to Bose- Einstein Condensate (BEC)

Mulmat, Christian

This research was focused on the construction of a magneto-optical trap (MOT) to create a Bose-Einstein Condensate (BEC) of 87Rb. The BEC is the coldest of the five states of matter functioning at a minuscule temperature of nanokelvin. A BEC is as close as we can get to absolute zero. Thus making it a valuable tool for researching the fundamental physics of quantum systems. Our setup utilizes both a high pressure and low-pressure MOT. The high-pressure MOT initiates the process with a high vapor density allowing for better Rb collection. The trapped atoms are then transported to the low-pressure MOT where there are no other atoms. Rb atoms are further cooled to a Bose-Einstein condensate temperature and are moved with more current-carrying coils to the glass BEC chamber. In the BEC chamber all Rb atoms are identical at their lowest quantum state. Although the process can be phrased in a few short sentences the setup and characterization of the entire system takes months to years of construction. # 43- 46 Environmental Fellows Program: Student Practicums

•Oct 2, 2019•0 citations

Realization of Bose-Einstein condensation in a rubidium vapor using a simple double magneto-optical trap

Yoshio Torii, Yoichi Suzuki, Mikio Kozuma +1 more

Since the first experimental demonstration of Bose-Einstein condensation (BEC) in an alkali-metal vapor, this subject has been attracting remarkable interests in the physics society. Hundreds of theoretical works concerning this subject have been reported so far. However, the number of reports about BEC experiments is much less than that of the theoretical works. This is because only a few experimental groups have succeeded in realizing BEC due to the experimental complexity and difficulties. The first step to create BEC in alkali-metal vapor is to collect a large number of atoms (/spl sim/-10/sup 9/) in an ultrahigh vacuum (/spl sim/10/sup 11/ torr). Recently, a double magneto-optical trap (MOT) system has been utilized for the first step. In this system, the atoms are first captured in a MOT from a vapor, and then transferred through a thin tube to the second MOT in an ultrahigh vacuum. To transfer the atoms, a pushing beam and a magnetic field are usually required to guide the atoms along the transfer tube. In the paper we report a simple double MOT system which uses neither a push beam nor a magnetic field to transfer the atoms. The atoms are transferred just by gravity. We can collect up to 2 x 10/sup 9/ rubidium atoms in the ultrahigh-vacuum MOT with this system and can achieve the BEC.

Conference on Lasers and Electro-Optics Pacific Rim (CLEO-PR)•Jan 20, 2003•0 citations

Optimization of Transfer of Cold Atoms From TwoDimensional Magneto Optical Trap to ThreeDimensional Magneto Optical Trap

Tirumalasetty Panduranga Mahesh, Nobuyuki Takei Supervisors Dr. Kenji Ohmori, Ayan Banerjee

This thesis reports on the generation of MOT for laser cooling and trapping of Rubidium 87 atoms. Probe-pump technique have been used in Rb gas cell and doppler free absorption peaks has been observed. Peak at the crossover frequency will be locked for laser cooling and repump beams. This locked freuqency used in MOT to trap Rb atoms. The technique of optical molasses is used to cool the atoms and quadrupole magnetic field applied to confine or trap atoms at the center of MOT. Two chambers are constructed for 2D and 3D MOT with different pressure. Rb atoms loaded efficiently from the high flux cold atom beam generated in a compact 2D MOT. This is the first step of Bose Einstein Condensate (BEC). A performance of 2D MOT was tested by another main chamber of 3D MOT contains 3 pairs of counter-propagating beams. Over 5x10⁶ atoms trapped in a 3D MOT with loading rate of 1:8x10⁶ atoms/sec. This experiment provided an excellent starting point for future experiment on Rydberg atoms in dense ultracold quantum gases.

•Apr 1, 2018•0 citations

Laser cooling of Rubidium atoms

Chung, Stephen

This thesis focuses on the construction of an atom trapping system utilising a hybrid trap setup to create a Bose-Einstein Condensate. The system involves a three chamber system, consisting of two magneto-optical traps for initial atom trapping and a science chamber to create and observe a BEC. The alkali metal of choice used in this experiment is ⁸⁷Rb, as it possesses favourable properties to create a BEC. A combination of Zeeman modulation frequency stabilisation and polarisation spectroscopy is used to lock our external-cavity diode laser into the right transition frequency and a tiny open-hardware called a Beaglebone is used to remotely access these controls. Beaglebones are also utilised for a double pass configuration of acousto-optic modulators for their convenient remote access which ultimately becomes the primary parameter for troubleshooting the optical part of the experiment. A standard push beam, with a much lower intensity compared to the MOT beams, is pulsed to transport the atoms from the first MOT chamber to the second MOT chamber. By moving the atom cloud to a much lower atmosphere (≈ 10⁻¹¹Torr), we are able to create a bigger atom cloud with a lower temperature which is essential in creating a BEC.

•Jan 1, 2020•0 citations

Design and Characterization of a Compact 2D Magneto-Optical Trap for Quantum Simulation Experiments

C. J. Ruiz Loredo, G. Ortiz Ugalde, José Mauricio López-Romero +2 more

This works presents the design, experimental implementation, and characterization of a compact 2D Magneto-Optical Trap (MOT) as a source of cold rubidium-87 atoms at the Quantum Technologies Laboratory in Cinvestav Queretaro. In a small volume vacuum chamber, the setup uses rubidium dispensers near to the trapping region of the 2D MOT and operates at low pressures in the 10-8torr range. The main idea of the 2D MOT is to use it as an atomic compact source for future experiments, such as the demonstration of Bose-Einstein Condensation, quantum simulation, spinor condensates and topological materials, quantum memories, etc.

Joint Conference of the European Frequency and Time Forum and IEEE International Frequency Control Symposium (EFTF/IFCS)•May 12, 2025•0 citations
A magneto-optical trap (MOT) for rubidium (Rb) atoms has been in operation at the University of San Carlos Optoelectronics Research Laboratory in Cebu City since 1998. The experimental design for this MOT is based on the system described by Wieman et al. (1995). This system formed the backbone of the research which resulted in the first observation of Bose-Einstein condensation (BEC) by the same group in 1995. An essential step for realizing this remarkable result was the accuracy in the timing mechanism of the experiment. To obtain an MOT in which we can switch the laser and magnetic fields with sub-millisecond accuracy, we have put considerable efforts to realize a computer-controlled system.
Previous measurements have been used to validate our new results. The realization of a fast switch for the trapping laser creates the opportunity to measure time-of-flight (TOF) signals. These ballistic measurements can be used to infer the temperature of the cloud of trapped atoms.
We hope to continue working on this automated system of the MOT towards BEC as a long-term goal of our research group.
Laser cooling experiments are a good example of how the interaction between light and matter can be applied to manipulate neutral atoms. At the University of San Carlos we have constructed a magneto-optical trap (MOT) for rubidium (Rb) atoms. The setup is based on the design of the MOT Wieman et al used in their efforts to reach Bose-Einstein condensation. The use of diode lasers enables the introduction of these advanced experiments at undergraduate level. Since 1998, when the MOT became operational at USC, a great number of undergraduate students have done the experiment. Not only did they learn the basics of cooling and trapping, they also gained experience in operating lasers properly, vacuum technology, and techniques for frequency stabilization. In some cases students opted to perform spectroscopy experiments on Rb atoms, which could easily be done using this setup. Of course, the presence of the MOT also gave a great boost to the research in optoelectronics, a new research direction in our department. Characterizing the MOT has resulted in several scientific papers in local physics journals as well as presentations to the annual Philippine Physics Congress. The next step is towards the realization of Bose-Einstein condensation of Rb in our Optoelectronics Laboratory.
This research was focused on the construction of a magneto-optical trap (MOT) to create a Bose-Einstein Condensate (BEC) of 87Rb. The BEC is the coldest of the five states of matter functioning at a minuscule temperature of nanokelvin. A BEC is as close as we can get to absolute zero. Thus making it a valuable tool for researching the fundamental physics of quantum systems. Our setup utilizes both a high pressure and low-pressure MOT. The high-pressure MOT initiates the process with a high vapor density allowing for better Rb collection. The trapped atoms are then transported to the low-pressure MOT where there are no other atoms. Rb atoms are further cooled to a Bose-Einstein condensate temperature and are moved with more current-carrying coils to the glass BEC chamber. In the BEC chamber all Rb atoms are identical at their lowest quantum state. Although the process can be phrased in a few short sentences the setup and characterization of the entire system takes months to years of construction. # 43- 46 Environmental Fellows Program: Student Practicums
Since the first experimental demonstration of Bose-Einstein condensation (BEC) in an alkali-metal vapor, this subject has been attracting remarkable interests in the physics society. Hundreds of theoretical works concerning this subject have been reported so far. However, the number of reports about BEC experiments is much less than that of the theoretical works. This is because only a few experimental groups have succeeded in realizing BEC due to the experimental complexity and difficulties. The first step to create BEC in alkali-metal vapor is to collect a large number of atoms (/spl sim/-10/sup 9/) in an ultrahigh vacuum (/spl sim/10/sup 11/ torr). Recently, a double magneto-optical trap (MOT) system has been utilized for the first step. In this system, the atoms are first captured in a MOT from a vapor, and then transferred through a thin tube to the second MOT in an ultrahigh vacuum. To transfer the atoms, a pushing beam and a magnetic field are usually required to guide the atoms along the transfer tube. In the paper we report a simple double MOT system which uses neither a push beam nor a magnetic field to transfer the atoms. The atoms are transferred just by gravity. We can collect up to 2 x 10/sup 9/ rubidium atoms in the ultrahigh-vacuum MOT with this system and can achieve the BEC.
This thesis reports on the generation of MOT for laser cooling and trapping of Rubidium 87 atoms. Probe-pump technique have been used in Rb gas cell and doppler free absorption peaks has been observed. Peak at the crossover frequency will be locked for laser cooling and repump beams. This locked freuqency used in MOT to trap Rb atoms. The technique of optical molasses is used to cool the atoms and quadrupole magnetic field applied to confine or trap atoms at the center of MOT. Two chambers are constructed for 2D and 3D MOT with different pressure. Rb atoms loaded efficiently from the high flux cold atom beam generated in a compact 2D MOT. This is the first step of Bose Einstein Condensate (BEC). A performance of 2D MOT was tested by another main chamber of 3D MOT contains 3 pairs of counter-propagating beams. Over 5x10⁶ atoms trapped in a 3D MOT with loading rate of 1:8x10⁶ atoms/sec. This experiment provided an excellent starting point for future experiment on Rydberg atoms in dense ultracold quantum gases.
This thesis focuses on the construction of an atom trapping system utilising a hybrid trap setup to create a Bose-Einstein Condensate. The system involves a three chamber system, consisting of two magneto-optical traps for initial atom trapping and a science chamber to create and observe a BEC. The alkali metal of choice used in this experiment is ⁸⁷Rb, as it possesses favourable properties to create a BEC. A combination of Zeeman modulation frequency stabilisation and polarisation spectroscopy is used to lock our external-cavity diode laser into the right transition frequency and a tiny open-hardware called a Beaglebone is used to remotely access these controls. Beaglebones are also utilised for a double pass configuration of acousto-optic modulators for their convenient remote access which ultimately becomes the primary parameter for troubleshooting the optical part of the experiment. A standard push beam, with a much lower intensity compared to the MOT beams, is pulsed to transport the atoms from the first MOT chamber to the second MOT chamber. By moving the atom cloud to a much lower atmosphere (≈ 10⁻¹¹Torr), we are able to create a bigger atom cloud with a lower temperature which is essential in creating a BEC.
This works presents the design, experimental implementation, and characterization of a compact 2D Magneto-Optical Trap (MOT) as a source of cold rubidium-87 atoms at the Quantum Technologies Laboratory in Cinvestav Queretaro. In a small volume vacuum chamber, the setup uses rubidium dispensers near to the trapping region of the 2D MOT and operates at low pressures in the 10-8torr range. The main idea of the 2D MOT is to use it as an atomic compact source for future experiments, such as the demonstration of Bose-Einstein Condensation, quantum simulation, spinor condensates and topological materials, quantum memories, etc.