Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconducting weak links for mixing at millimeter-wave frequencies. Final report, 15 June 1970--14 June 1973

T. Van Duzer

Published Jan 1, 1973• 0 citations
OpenAlex

Abstract

The goals of the work were to fabricate superconductive thin-film constrictions with an electron microscope and to test them as mixers. During the grant period indium and vanadium constrictions were made with submicron dimensions and these were tested in detection and mixing modes. Most of the tests were conducted at X-band frequencies and some were done at V-band. A computer program was developed to study the theoretical behavior of a circuit model of Josephson devices such as thin-film constrictions. Considerable information was derived from the calculations and good agreement with experiments was obtained in some cases. In the process of developing sufficient understanding of electron-resist exposures, the author worked out a theory which gives general guidance for the use of electron resists for microdevice fabrication. Simple arrays of two and three devices were studied under dc conditions. A theoretical description of a generally asymmetric array was developed, taking account of the self- and mutual inductances.

Related papers

Mixing in superconducting weak links : numerical calculations and experimental results

F. Auracher, T. Van Duzer

We report here numerical calculations on the properties of superconducting weak links as mixers with external local oscillators (LO). Our calculations are based on the resistively shunted-junction model. We assume that the LO and the signal are ideal current sources of amplitudes ILO and IS and of frequencies ωLO and ωs, respectively. We calculate the IF voltage across the weak link as a function of the bias current, the LO current amplitude ILO, and the normalized signal frequency Ωs = ħωs/(2 e Ic R), where Ic is the critical current and R is the shunt resistance. If ωIF/ωLO and Is/Ic are small, we find a linear IF response. Using this method we find the frequency dependence of the IF response, estimate the conversion efficiency for the matched case in both the absence and the presence of noise, and calculate the required LO power. We have fabricated thin-film constrictions by using electron lithography. We have made constrictions of indium films with thicknesses of ~ 1 200 A with widths as narrow as 2 000 A and lengths as short as 1 000 A and have studied their I-V characteristics in the presence of RF radiation and measured their X-band mixing properties. We have measured an NEP of 10-13 W/Hz1/2 and a dynamic range of 23 dB (3 dB deviation from linearity) and estimate that, with optimum matching, these would become 3 × 10-18 W/Hz1/2 and 74 dB, respectively.

Revue de Physique Appliquée•Jan 1, 1974•23 citations

The AC Josephson effect and submillimeter wave mixing with a weak-link array of grain boundaries formed in YBCO film

Toshiaki Matsui, Hiroshi Ohta

The authors present a model for a series-parallel array of small metallic (nontunneling) Josephson junctions. The transmission and configuration of pair electrons between small superconducting regions are considered assuming the presence of a strong interaction between the electrostatic energy (2e)/sup 2//2C and the Josephson effect in a network of metallic weak links. The model predicts that the same behavior as that of a single junction is obtained with a superconducting weak-link device comprising multiple small superconducting regions joined by conductive bridges. In an experiment in the 100- and 320-GHz frequency ranges, the constriction of a YBCO film formed with a network of grain-boundary Josephson weak links showed that the AC Josephson effect is the same as for a single Josephson element. It is confirmed that the constriction works as a harmonic mixer at 318 GHz and that a network of high-T/sub c/ superconducting weak links can be used for a practical device operating at submillimeter-wave frequencies.>

IEEE Transactions on Applied Superconductivity•Mar 1, 1993•15 citations

Microwave properties of variable thin-film Josephson bridges

V. Gubankov, V. P. Koshelets, G. A. Ovsyannikov +1 more

Amplification, down-conversion and detection of the microwaves in thin-film Josephson variable thickness bridges of submicron dimensions have been investigated experimentally. The results for indium and tin bridges are discussed taking into account the influence of the nonequilibrium electrons in a weak link region. The same experiments were carried out with SNS variable thickness Nb-Al-Nb bridges. They showed that the properties of SNS bridges agreed better with the theoretical predictions of the resistively shunted junction model in a wide temperature range. Moreover the parameters of the Nb-Al-Nb bridges have possessed better stability and reliability.

IEEE Transactions on Magnetics•Jan 1, 1979•6 citations

Research on superconducting signal processing devices. Final technical report

T. Van Duzer

An understanding of the role of alloying elements in lead thin films for use as Josephson junctions was achieved, and thermally cyclable devices were made. Gold is one of the elements which strongly inhabit the movement of grain boundaries and thus prevent the growth of hillocks and whiskers on the film which would puncture the thin oxide barrier. A new technology in which thin silicon membranes supported by a surrounding frame can be used for device fabrication was developed. This includes a double-etching scheme to achieve even submicron size membranes having thickness of no more than a few hundred angstroms. We have shown that advantages can be had by fabricating Schottky and super-Schottky diodes on such membranes. Also, Josephson junctions made this way show promise of great design flexibility and may develop into the best Josephson device for mixing and detection. Two ways of making double weak superconducting links for possible use as switching elements were tested. It appears that the impedance level is lower than would be desired for that application for the dimensions used so far but fabrication by electron lithography would increase it. The semiconductor barrier is analyzed, as a possible Josephson junction switching element and itmore » appears to have some advantages. One of these is a lower Q for the junction cavity; our analysis shows about two orders of magnitude improvement in this regard over oxide-barrier junctions. (GRA)« less

•Jan 1, 1975•0 citations

Recent advances in superconducting-mixer simulations

S. Withington, Philippa R Kennedy

Over the last few years, considerable progress have been made in the development of techniques for fabricating high-quality superconducting circuits, and this success, together with major advances in the theoretical understanding of quantum detection and mixing at millimeter and submillimeter wavelengths, has made the development of CAD techniques for superconducting nonlinear circuits an important new enterprise. For example, arrays of quasioptical mixers are now being manufactured, where the antennas, matching networks, filters and superconducting tunnel junctions are all fabricated by depositing niobium and a variety of oxides on a single quartz substrate. There are no adjustable tuning elements on these integrated circuits, and therefore, one must be able to predict their electrical behavior precisely. This requirement, together with a general interest in the generic behavior of devices such as direct detectors and harmonic mixers, has lead us to develop a range of CAD tools for simulating the large-signal, small-signal, and noise behavior of superconducting tunnel junction circuits.

•Jan 1, 1992•0 citations

Millimeter and submillimeter wave detection and mixing with superconducting weak links

P. L. Richards, F. Auracher, T. Van Duzer

A weak link between two bulk superconductors can exhibit Josephson effects and can be used as a fast sensitive detector or mixer for electromagnetic radiation. Emphasis is placed on the millimeter and submillimeter range where such applications are potentially most important, though such devices should also work well at lower frequencies. The peculiar properties of the weak link make possible a variety of modes of operation including one in which it is both local oscillator and mixer. These modes of operation are analyzed and the pivotal experiments are reviewed. Noise and impedance matching are considered and comparison is made with other types of detectors of millimeter and submillimeter waves.

Proceedings of the IEEE•Jan 1, 1973•41 citations
The goals of the work were to fabricate superconductive thin-film constrictions with an electron microscope and to test them as mixers. During the grant period indium and vanadium constrictions were made with submicron dimensions and these were tested in detection and mixing modes. Most of the tests were conducted at X-band frequencies and some were done at V-band. A computer program was developed to study the theoretical behavior of a circuit model of Josephson devices such as thin-film constrictions. Considerable information was derived from the calculations and good agreement with experiments was obtained in some cases. In the process of developing sufficient understanding of electron-resist exposures, the author worked out a theory which gives general guidance for the use of electron resists for microdevice fabrication. Simple arrays of two and three devices were studied under dc conditions. A theoretical description of a generally asymmetric array was developed, taking account of the self- and mutual inductances.
We report here numerical calculations on the properties of superconducting weak links as mixers with external local oscillators (LO). Our calculations are based on the resistively shunted-junction model. We assume that the LO and the signal are ideal current sources of amplitudes ILO and IS and of frequencies ωLO and ωs, respectively. We calculate the IF voltage across the weak link as a function of the bias current, the LO current amplitude ILO, and the normalized signal frequency Ωs = ħωs/(2 e Ic R), where Ic is the critical current and R is the shunt resistance. If ωIF/ωLO and Is/Ic are small, we find a linear IF response. Using this method we find the frequency dependence of the IF response, estimate the conversion efficiency for the matched case in both the absence and the presence of noise, and calculate the required LO power. We have fabricated thin-film constrictions by using electron lithography. We have made constrictions of indium films with thicknesses of ~ 1 200 A with widths as narrow as 2 000 A and lengths as short as 1 000 A and have studied their I-V characteristics in the presence of RF radiation and measured their X-band mixing properties. We have measured an NEP of 10-13 W/Hz1/2 and a dynamic range of 23 dB (3 dB deviation from linearity) and estimate that, with optimum matching, these would become 3 × 10-18 W/Hz1/2 and 74 dB, respectively.
The authors present a model for a series-parallel array of small metallic (nontunneling) Josephson junctions. The transmission and configuration of pair electrons between small superconducting regions are considered assuming the presence of a strong interaction between the electrostatic energy (2e)/sup 2//2C and the Josephson effect in a network of metallic weak links. The model predicts that the same behavior as that of a single junction is obtained with a superconducting weak-link device comprising multiple small superconducting regions joined by conductive bridges. In an experiment in the 100- and 320-GHz frequency ranges, the constriction of a YBCO film formed with a network of grain-boundary Josephson weak links showed that the AC Josephson effect is the same as for a single Josephson element. It is confirmed that the constriction works as a harmonic mixer at 318 GHz and that a network of high-T/sub c/ superconducting weak links can be used for a practical device operating at submillimeter-wave frequencies.>
Amplification, down-conversion and detection of the microwaves in thin-film Josephson variable thickness bridges of submicron dimensions have been investigated experimentally. The results for indium and tin bridges are discussed taking into account the influence of the nonequilibrium electrons in a weak link region. The same experiments were carried out with SNS variable thickness Nb-Al-Nb bridges. They showed that the properties of SNS bridges agreed better with the theoretical predictions of the resistively shunted junction model in a wide temperature range. Moreover the parameters of the Nb-Al-Nb bridges have possessed better stability and reliability.
An understanding of the role of alloying elements in lead thin films for use as Josephson junctions was achieved, and thermally cyclable devices were made. Gold is one of the elements which strongly inhabit the movement of grain boundaries and thus prevent the growth of hillocks and whiskers on the film which would puncture the thin oxide barrier. A new technology in which thin silicon membranes supported by a surrounding frame can be used for device fabrication was developed. This includes a double-etching scheme to achieve even submicron size membranes having thickness of no more than a few hundred angstroms. We have shown that advantages can be had by fabricating Schottky and super-Schottky diodes on such membranes. Also, Josephson junctions made this way show promise of great design flexibility and may develop into the best Josephson device for mixing and detection. Two ways of making double weak superconducting links for possible use as switching elements were tested. It appears that the impedance level is lower than would be desired for that application for the dimensions used so far but fabrication by electron lithography would increase it. The semiconductor barrier is analyzed, as a possible Josephson junction switching element and itmore » appears to have some advantages. One of these is a lower Q for the junction cavity; our analysis shows about two orders of magnitude improvement in this regard over oxide-barrier junctions. (GRA)« less
Over the last few years, considerable progress have been made in the development of techniques for fabricating high-quality superconducting circuits, and this success, together with major advances in the theoretical understanding of quantum detection and mixing at millimeter and submillimeter wavelengths, has made the development of CAD techniques for superconducting nonlinear circuits an important new enterprise. For example, arrays of quasioptical mixers are now being manufactured, where the antennas, matching networks, filters and superconducting tunnel junctions are all fabricated by depositing niobium and a variety of oxides on a single quartz substrate. There are no adjustable tuning elements on these integrated circuits, and therefore, one must be able to predict their electrical behavior precisely. This requirement, together with a general interest in the generic behavior of devices such as direct detectors and harmonic mixers, has lead us to develop a range of CAD tools for simulating the large-signal, small-signal, and noise behavior of superconducting tunnel junction circuits.
A weak link between two bulk superconductors can exhibit Josephson effects and can be used as a fast sensitive detector or mixer for electromagnetic radiation. Emphasis is placed on the millimeter and submillimeter range where such applications are potentially most important, though such devices should also work well at lower frequencies. The peculiar properties of the weak link make possible a variety of modes of operation including one in which it is both local oscillator and mixer. These modes of operation are analyzed and the pivotal experiments are reviewed. Noise and impedance matching are considered and comparison is made with other types of detectors of millimeter and submillimeter waves.