A simple and robust process for fabricating low-T/sub c/ Josephson junction integrated circuits has been developed. The process is designed around the Nb/Al/sub 2/O/sub 3/-Al/Nb trilayer, and utilized nine masking steps to form two separate levels of trilayer Josephson junctions, as well as resistors, capacitors, and transmission lines. Materials used for interlayer dielectrics and passivation layers are silicon dioxide and silicon nitride formed by plasma-enhanced chemical vapor deposition (PECVD). The PECVD equipment yields a high deposition rate at moderate substrate temperatures. No degradation of the junction characteristics due to these depositions is seen. The measured loss tangent of this dielectric at 10 GHz using a parallel plate technique is 4.44*10/sup -4/. The dielectric constant of this material is 5.1 in the range of 50 to 400 GHz, measured using an on-chip resonator capacitively coupled to a single shunted Josephson junction. The physical quality of the oxide has been investigated using a variety of tests and has proven to be excellent. A variety of simple circuits using this process technology have been fabricated and tested. More complex circuits are currently under development.
We have developed a new integration method for Josephson tunnel junctions based on high Tc superconducting compound materials such as NbN. In this method, a sputtered ZnO film has been employed as a resist mask which can be used in high substrate temperatures during the film deposition. It has been found that fine patterns of the refractory superconducting film can be obtained by this method and the patterning processes have no interference with other integration processes. We have applied this method to patterning base electrode of NbN and formed high quality NbN-oxide-Pb Josephson tunnel junctions by using an rf plasma oxidation. The fabricated junctions have been found to have a relatively large gap ( ∼ 4.0 mV ) and low current leak in the subgap region, and to be quite stable for thermal cyclings and storage. We have also fabricated quantum interference memory devices by integrating these junctions and the operation has been successfully demonstrated.
Superconducting qubits in today's quantum processing units are typically fabricated with angle-evaporated aluminum--aluminum-oxide--aluminum Josephson junctions. However, there is an urgent need to overcome the limited reproducibility of this approach when scaling up the number of qubits and junctions. Fabrication methods based on subtractive patterning of superconductor--insulator--superconductor trilayers, used for more classical large-scale Josephson junction circuits, could provide the solution but they in turn often suffer from lossy dielectrics incompatible with high qubit coherence. In this work, we utilize native aluminum oxide as a sidewall passivation layer for junctions based on aluminum--aluminum-oxide--niobium trilayers, and use such junctions in qubits. We design the fabrication process such that the few-nanometer-thin native oxide is not exposed to oxide removal steps that could increase its defect density or hinder its ability to prevent shorting between the leads of the junction. With these junctions, we design and fabricate transmon-like qubits and measure time-averaged coherence times up to 30
μs at a qubit frequency of 5 GHz, corresponding to a qubit quality factor of one million. Our process uses subtractive patterning and optical lithography on wafer scale, enabling high throughput in patterning. This approach provides a scalable path toward fabrication of superconducting qubits on industry-standard platforms.
A trilayer deposition process for making high quality all-refractory Nb/AlOx/Nb Josephson junctions is described. The sputtering parameters were optimized to deposit very uniform Al films, less than 5 nm in thickness. We found that it was essential to keep the substrate temperature below 40 °C during Al deposition but not during Nb depositions. Rapid anodization of the Nb counterelectrode allowed us to use positive photoresist as an anodization mask even for submicron geometries. The dc superconducting quantum interference devices made with this process have the lowest intrinsic energy sensitivity reported to date for an all-refractory technology.
We have developed a fabrication technology for superconducting integrated circuits with Nb-based Josephson junctions. The standard fabrication process with 10 mask levels includes 3 Nb superconducting layers and a Mo resistor layer. The influence of deposition parameters on film stress, electrical properties, and surface roughness were studied systematically. High quality Nb, Al, Mo, and SiO2films were successfully deposited for the subsequent fabrication of circuits. The circuit fabrication started with the fabrication of Mo resistors with a target sheet resistanceRshof 2 Ω, followed by the deposition of Nb/Al-AlOx/Nb trilayer Josephson-junction. The target critical current densityJcwas set at 6 kA/cm2. Small-scale circuits such as our standard library cells have been successfully fabricated and tested, confirming the capability of our fabrication technology for superconducting integrated circuits.
Tantalum (Ta) has emerged as a promising low-loss material, enabling record coherence times in superconducting qubits. This enhanced performance is largely attributed to its stable native oxide, which may host fewer two-level system (TLS) defects, which are the key contributors to decoherence in superconducting circuits. Nevertheless, aluminum oxide remains the predominant choice for Josephson junction (JJ) barriers in most qubit architectures. Here, we investigate techniques for forming high-quality oxide layers on
α-phase tantalum films to develop tantalum-oxide JJ barriers. We explore thermal oxidation in a tube furnace, rapid thermal annealing, and plasma oxidation of both room-temperature and heated Ta films, characterize the resulting structures using X-ray techniques and electron microscopy, and propose a mechanistic picture of the oxidation pathways. We find that plasma oxidation provides the smoothest Ta
2O
5 layers, is compatible with in situ Ta deposition, and offers thickness control through the annealing temperature, advantageous for JJ fabrication. Lastly, we evaluate methods for growing Ta/TaO
x/Ta trilayers. All trilayers showed c-axis-oriented columnar growth of the bottom Ta layer, with sapphire substrates producing larger, better-aligned grains yet higher dislocation densities than silicon. Nucleation of c-axis-oriented
α-Ta on tantalum-oxide required an Nb seed layer, as direct Ta deposition yielded amorphous Ta. These results demonstrate the feasibility of
α-Ta/Nb/TaO
x/
α-Ta stacks for JJs with clean interfaces.