Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Applied Physics Letters

Nb/AlOx/Nb trilayer process for the fabrication of submicron Josephson junctions and low-noise dc SQUIDs

Manjul Bhushan, E. M. Macedo

Published Mar 25, 1991• 43 citations
Publisher

Abstract

A trilayer deposition process for making high quality all-refractory Nb/AlOx/Nb Josephson junctions is described. The sputtering parameters were optimized to deposit very uniform Al films, less than 5 nm in thickness. We found that it was essential to keep the substrate temperature below 40 °C during Al deposition but not during Nb depositions. Rapid anodization of the Nb counterelectrode allowed us to use positive photoresist as an anodization mask even for submicron geometries. The dc superconducting quantum interference devices made with this process have the lowest intrinsic energy sensitivity reported to date for an all-refractory technology.

DOI
10.1063/1.104298

Related papers

Low noise DC SQUIDs fabricated in Nb-Al/sub 2/O/sub 3/-Nb trilayer technology

M. B. Ketchen, Manjul Bhushan, Steven B. Kaplan +1 more

The authors have designed, fabricated and tested all-refractory DC SQUIDs in Nb-Al/sub 2/O/sub 3/-Nb trilayer technology that have noise performance comparable to the best previously reported for any technology. A variety of SQUID designs were incorporated as part of a trilayer process development test vehicle. SQUID inductance, junction area, and resistive shunt geometry were varied in matrix fashion to give SQUIDs with near-optimum parameter values for a factor of five range in Josephson current density and shunt sheet resistance. The devices were fabricated using a selective niobium anodization with a minimum feature size of 2 mu m. The base electrode and Nb wiring were patterned with dry etching, and the junction areas were defined by anodization: the Ti resistors were patterned with a lift-off process. Current density on different wafers was varied from 400 to 1000 A/cm/sup 2/ with typical junction V/sub m/'s of 60 mV. The shunt sheet resistance was varied in the 1-5- Omega / Square Operator range. The noise was measured with an RF SQUID direct small-signal readout scheme. A 50-pH SQUID with 3- mu m/sup 2/, 16- mu A junctions and 14- Omega shunt resistors was shown to have an ideally low white noise of 1*10/sup -13/ Phi /sub 0//sup 2//Hz, a white to 1/f crossover frequency at 7 Hz, and a noise level less than 6*10/sup -12/ Phi /sub 0//sup 2//Hz at 0.1 Hz.

IEEE Transactions on Magnetics•Mar 1, 1991•25 citations

Sub-μm, planarized, Nb-AlOx-Nb Josephson process for 125 mm wafers developed in partnership with Si technology

M. B. Ketchen, Dale J. Pearson, Alan W. Kleinsasser +14 more

We have demonstrated a new planarized all-refractory technology for low Tc superconductivity (PARTS). With the exception of the Nb-AlOx-Nb trilayer preparation, the processing is done almost exclusively within an advanced Si technology fabrication facility. This approach has allowed us to leverage highly off of existing state-of-the-art lithography, metal etching, materials deposition, and planarization capabilities. Using chemical-mechanical polish as the planarization technique we have fabricated Josephson junctions ranging in size from 0.5–100 μm2. Junction quality is excellent with the figure of merit Vm typically exceeding 70 mV. PARTS has yielded fully functional integrated Josephson devices including magnetometers, gradiometers, and soliton oscillators.

Applied Physics Letters•Nov 11, 1991•106 citations

Anodization-free fabrication process for high-quality cross-type Josephson tunnel junctions based on a Nb/Al-AlO x /Nb trilayer

F Adam, C. Enss, Sebastian Kempf

Abstract Josephson tunnel junctions form the basis for various superconductor electronic devices. For this reason, enormous efforts are routinely taken to establish and later on maintain a scalable and reproducible wafer-scale manufacturing process for high-quality Josephson junctions. Here, we present an anodization-free fabrication process for Nb/Al-AlO x /Nb cross-type Josephson junctions that requires only a small number of process steps and that is in general intrinsically compatible with wafer-scale fabrication. We show that the fabricated junctions are of very high quality and, compared to other junction types, exhibit not only a significantly reduced capacitance but also an almost rectangular critical current density profile. Our process hence enables the usage of low capacitance Josephson junctions for superconductor electronic devices such as ultra-low noise dc-superconducting quantum interference devices (SQUIDs), microwave SQUID multiplexers based on non-hysteretic rf-SQUIDs and RFSQ circuits.

arXiv:2403.01806•Superconductor Science and Technology•Jul 8, 2024•6 citations

Film Stress Influence on Nb/Al-AlO x /Nb Josephson Junctions

Yu Wu, Liliang Ying, Guanqun Li +4 more

Nb/Al-AlOx/Nb Josephson junctions are widely used in superconducting quantum interference devices and rapid single flux quantum (RSFQ) circuits. Very large-scale RSFQ integration often has a strict requirement on wafer-scale junction qualities. In particular, Nb film stress in Nb/Al-AlOx/Nb trilayer based Josephson junctions is a critical factor affecting their qualities. In this work, we develop a multi-step sputtering process to prepare Nb films with different combinations of stress and roughness to investigate the correlation between Nb film stress and junction quality. In particular, this method allows us to prepare Nb films with almost the same roughness but different stress, a key factor to study solely the influence of stress on junction qualities. Our measurements indicate that within a very tight range of film roughness (less than 2 nm), tensile film stress is found to decrease the quality of Nb/Al-AlOx/Nb Josephson junctions and larger film roughness has a positive effect on junction quality. By decreasing the total tensile stress and increasing the film roughness properly, we fabricated Nb/Al-AlOx/Nb Josephson junctions with a high quality factor characterized by Rsg/RN(30 on average). The minimum size of junctions was 1 μm.

IEEE Transactions on Applied Superconductivity•Mar 18, 2019•28 citations

Aluminum hard mask technique for the fabrication of high quality submicron Nb/Al–AlOx/Nb Josephson junctions

Ch Kaiser, J M Meckbach, K S Ilin +4 more

We have developed a combined photolithography and electron-beam lithography fabrication process for sub-\mum to \mum-size Nb/Al-AlOx/Nb Josephson junctions. In order to define the junction size and protect its top electrode during anodic oxidation, we developed and used the new concept of an aluminum hard mask. Josephson junctions of sizes down to 0.5 \mum2 have been fabricated and thoroughly characterized. We found that they have a very high quality, which is witnessed by the IV curves with quality parameters Vm > 50 mV and Vgap = 2.8 mV at 4.2 K, as well as IcRN products of 1.75-1.93 mV obtained at lower temperatures. In order to test the usability of our fabrication process for superconducting quantum bits, we have also designed, fabricated and experimentally investigated phase qubits made of these junctions. We found a relaxation time of T1 = 26 ns and a dephasing time of T2 = 21 ns.

arXiv:1009.0167•Superconductor Science and Technology•Dec 23, 2010•18 citations

Nb/AlOx/Nb Josephson Tunnel Junctions Using Electron Beam Evaporation

Atsuki Inoue, Akiyoshi Nakayama, Yoichi Okabe

Niobium/aluminum-oxide/niobium Josephson tunnel junctions have been fabricated using electron beam evaporation to form all-metal films in a high vacuum system. A quality factor, V m (the product of the maximum dc Josephson current and the subgap resistance defined at 2 mV) between 36–37 mV, has been obtained for the best junctions of a 6 nm-thick Al layer by cooling down the surface of the base electrode for 100 minutes under a high background pressure, before the deposition of aluminum, after the formation of the base niobium electrode. An array of 80 series-connected junctions has also been fabricated using the selective niobium anodization process and the planarization process. The current-voltage characteristics of the array showed a standard deviation of the maximum dc Josephson current of 3.3%.

Japanese Journal of Applied Physics•Jul 1, 1988•10 citations
A trilayer deposition process for making high quality all-refractory Nb/AlOx/Nb Josephson junctions is described. The sputtering parameters were optimized to deposit very uniform Al films, less than 5 nm in thickness. We found that it was essential to keep the substrate temperature below 40 °C during Al deposition but not during Nb depositions. Rapid anodization of the Nb counterelectrode allowed us to use positive photoresist as an anodization mask even for submicron geometries. The dc superconducting quantum interference devices made with this process have the lowest intrinsic energy sensitivity reported to date for an all-refractory technology.
The authors have designed, fabricated and tested all-refractory DC SQUIDs in Nb-Al/sub 2/O/sub 3/-Nb trilayer technology that have noise performance comparable to the best previously reported for any technology. A variety of SQUID designs were incorporated as part of a trilayer process development test vehicle. SQUID inductance, junction area, and resistive shunt geometry were varied in matrix fashion to give SQUIDs with near-optimum parameter values for a factor of five range in Josephson current density and shunt sheet resistance. The devices were fabricated using a selective niobium anodization with a minimum feature size of 2 mu m. The base electrode and Nb wiring were patterned with dry etching, and the junction areas were defined by anodization: the Ti resistors were patterned with a lift-off process. Current density on different wafers was varied from 400 to 1000 A/cm/sup 2/ with typical junction V/sub m/'s of 60 mV. The shunt sheet resistance was varied in the 1-5- Omega / Square Operator range. The noise was measured with an RF SQUID direct small-signal readout scheme. A 50-pH SQUID with 3- mu m/sup 2/, 16- mu A junctions and 14- Omega shunt resistors was shown to have an ideally low white noise of 1*10/sup -13/ Phi /sub 0//sup 2//Hz, a white to 1/f crossover frequency at 7 Hz, and a noise level less than 6*10/sup -12/ Phi /sub 0//sup 2//Hz at 0.1 Hz.
We have demonstrated a new planarized all-refractory technology for low Tc superconductivity (PARTS). With the exception of the Nb-AlOx-Nb trilayer preparation, the processing is done almost exclusively within an advanced Si technology fabrication facility. This approach has allowed us to leverage highly off of existing state-of-the-art lithography, metal etching, materials deposition, and planarization capabilities. Using chemical-mechanical polish as the planarization technique we have fabricated Josephson junctions ranging in size from 0.5–100 μm2. Junction quality is excellent with the figure of merit Vm typically exceeding 70 mV. PARTS has yielded fully functional integrated Josephson devices including magnetometers, gradiometers, and soliton oscillators.
Abstract Josephson tunnel junctions form the basis for various superconductor electronic devices. For this reason, enormous efforts are routinely taken to establish and later on maintain a scalable and reproducible wafer-scale manufacturing process for high-quality Josephson junctions. Here, we present an anodization-free fabrication process for Nb/Al-AlO x /Nb cross-type Josephson junctions that requires only a small number of process steps and that is in general intrinsically compatible with wafer-scale fabrication. We show that the fabricated junctions are of very high quality and, compared to other junction types, exhibit not only a significantly reduced capacitance but also an almost rectangular critical current density profile. Our process hence enables the usage of low capacitance Josephson junctions for superconductor electronic devices such as ultra-low noise dc-superconducting quantum interference devices (SQUIDs), microwave SQUID multiplexers based on non-hysteretic rf-SQUIDs and RFSQ circuits.
Nb/Al-AlOx/Nb Josephson junctions are widely used in superconducting quantum interference devices and rapid single flux quantum (RSFQ) circuits. Very large-scale RSFQ integration often has a strict requirement on wafer-scale junction qualities. In particular, Nb film stress in Nb/Al-AlOx/Nb trilayer based Josephson junctions is a critical factor affecting their qualities. In this work, we develop a multi-step sputtering process to prepare Nb films with different combinations of stress and roughness to investigate the correlation between Nb film stress and junction quality. In particular, this method allows us to prepare Nb films with almost the same roughness but different stress, a key factor to study solely the influence of stress on junction qualities. Our measurements indicate that within a very tight range of film roughness (less than 2 nm), tensile film stress is found to decrease the quality of Nb/Al-AlOx/Nb Josephson junctions and larger film roughness has a positive effect on junction quality. By decreasing the total tensile stress and increasing the film roughness properly, we fabricated Nb/Al-AlOx/Nb Josephson junctions with a high quality factor characterized by Rsg/RN(30 on average). The minimum size of junctions was 1 μm.
We have developed a combined photolithography and electron-beam lithography fabrication process for sub-\mum to \mum-size Nb/Al-AlOx/Nb Josephson junctions. In order to define the junction size and protect its top electrode during anodic oxidation, we developed and used the new concept of an aluminum hard mask. Josephson junctions of sizes down to 0.5 \mum2 have been fabricated and thoroughly characterized. We found that they have a very high quality, which is witnessed by the IV curves with quality parameters Vm > 50 mV and Vgap = 2.8 mV at 4.2 K, as well as IcRN products of 1.75-1.93 mV obtained at lower temperatures. In order to test the usability of our fabrication process for superconducting quantum bits, we have also designed, fabricated and experimentally investigated phase qubits made of these junctions. We found a relaxation time of T1 = 26 ns and a dephasing time of T2 = 21 ns.
Niobium/aluminum-oxide/niobium Josephson tunnel junctions have been fabricated using electron beam evaporation to form all-metal films in a high vacuum system. A quality factor, V m (the product of the maximum dc Josephson current and the subgap resistance defined at 2 mV) between 36–37 mV, has been obtained for the best junctions of a 6 nm-thick Al layer by cooling down the surface of the base electrode for 100 minutes under a high background pressure, before the deposition of aluminum, after the formation of the base niobium electrode. An array of 80 series-connected junctions has also been fabricated using the selective niobium anodization process and the planarization process. The current-voltage characteristics of the array showed a standard deviation of the maximum dc Josephson current of 3.3%.