Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2011.06272 · IEEE Transactions on Applied Superconductivity

Development of Multi-Layer Fabrication Process for SFQ Large Scale Integrated Digital Circuits

Liliang Ying, Xue Zhang, Minghui Niu, Jie Ren, Wei Peng, Masaaki Maezawa, Zhen Wang

Published Mar 11, 2021• 79 citations
arXivHTMLPDF

Abstract

We have developed a fabrication technology for superconducting integrated circuits with Nb-based Josephson junctions. The standard fabrication process with 10 mask levels includes 3 Nb superconducting layers and a Mo resistor layer. The influence of deposition parameters on film stress, electrical properties, and surface roughness were studied systematically. High quality Nb, Al, Mo, and SiO2films were successfully deposited for the subsequent fabrication of circuits. The circuit fabrication started with the fabrication of Mo resistors with a target sheet resistanceRshof 2 Ω, followed by the deposition of Nb/Al-AlOx/Nb trilayer Josephson-junction. The target critical current densityJcwas set at 6 kA/cm2. Small-scale circuits such as our standard library cells have been successfully fabricated and tested, confirming the capability of our fabrication technology for superconducting integrated circuits.

DOI
10.1109/tasc.2021.3065277

Related papers

Development of 15kA/cm$^2$ Fabrication Process for Superconducting Integrated Digital Circuits

Liliang Ying, Xue Zhang, Guixiang He +7 more

A new fabrication process for superconducting integrated digital circuits is reported. We have developed the "SIMIT Nb04" fabrication technique for superconducting integrated circuits with Nb-based Josephson junctions based on the validated "SIMIT Nb03" process and Chemical Mechanical Planarization (CMP) technology. Seven Nb superconducting layers and one Mo resistor layer are included in the "SIMIT Nb04" process with 19 mask levels. The device structure is composed of active layers including junctions at the bottom, two passive transmission line (PTL) layers in the middle and a DC power layer at the top. The circuit fabrication started with the fabrication of Mo resistors with a target sheet resistance Rsh of 3 $Ω$, followed by the deposition of Nb/Al-AlO$_x$/Nb trilayer Josephson-junction with a target critical current density Jc at 15 kA/cm$^2$. To increase the Al-AlO$_x$ barrier layer etching's repeatability, an additional barrier protection layer was applied. To accomplish high-quality planarization, we created a planarization procedure coupled with dummy filling. To assess the process dependability and controllability, a set of process control monitors (PCMs) for monitoring fabrication and design parameters was designed and monitored. The successful manufacturing and testing of a few small-scale circuits, like our standard library cells, further attests to the viability of our fabrication process for superconducting integrated circuits.

arXiv:2304.01588•Apr 4, 2023•2 citations

Development of Nb/Al–AlOx/Nb Tunnel Junction for Large-Scale Integrated Digital Circuits

Wei Xiong, Liliang Ying, Yu Wu +3 more

We present the latest development of an Nb/Al-AlOx/Nb Josephson junction fabrication process for superconducting integrated circuits at SIMIT. Our fabrication process has four niobium superconducting layers and one Ti/Pd resistor layer with 1.0 Ω/square sheet resistor for junction shunting and circuit biasing. Critical current density Jcof the junctions is controlled from 30 A/cm2to 10 kA/cm2by exposing aluminum layer to pure or mixed O2atmosphere. Correlation between measured Jcand exposure conditions has been established. Average quality factor (Rsg/Rn) of the junctions in our process is larger than 20 with subgap leakage factor (Vm) beyond 30 mV. Critical current uniformity is obtained according to the switching current (Is) distribution of a 1000-JJ array. Measured standard deviation sigma of Isis less than 4% over the 100-mm wafer. Plasma resonance in a large Josephson junction is used to measure specific capacitance (Cs) of the junction. Sheet inductances of superconducting niobium strip-lines are extracted by a SQUID diagnose circuit and the measured results show good agreement with our design values.

IEEE Transactions on Applied Superconductivity•Dec 24, 2016•13 citations

Process Control Monitoring for Fabrication Technology of Superconducting Integrated Circuits

Xue Zhang, Liliang Ying, Minghui Niu +16 more

We have developed a 6-kA/cm superconducting integrated circuit fabrication process toward large-scale single flux quantum digital circuits. To evaluate the process reliability and controllability, a set of process control monitors (PCMs) for monitoring fabrication and design parameters was designed and tested. Fabrication parameters, for example, film thicknesses and etched depths of the layers, were measured by testing specific patterns during fabrication. Design parameters such as the critical current density Jc, normal-state resistance Rnand actual sizes of Josephson junctions, the sheet resistance of Mo resistor Rsh, and the penetration depth of Nb films were evaluated by electrically characterizing PCM circuits after fabrication. We also monitored superconducting critical currents for vias and Nb lines, and insulation properties between the metal layers systematically.

IEEE Transactions on Applied Superconductivity•Mar 30, 2021•23 citations

Current status and future prospect of the Nb-based fabrication process for single flux quantum circuits

Mutsuo Hidaka, Shuichi Nagasawa, T. Satoh +2 more

The Superconductivity Research Laboratory has successfully fabricated large quantities of single flux quantum (SFQ) large scale integrated circuits, including several thousands of Josephson junctions (JJs). Using a Jc = 2.5 kA cm−2 process in which the number of Nb layers was four and the minimum JJ size was 2 µm square. We developed a new advanced fabrication process that produced a Jc = 10 kA cm−2, nine Nb layers and a minimum JJ size of 1 µm square. The increase in the number of Nb layers was achieved by using a planarization technique. The target of our next generation process is a Jc = 40 kA cm−2 with a 0.5 µm square for the minimum junction size. This specification will be achieved by using advanced semiconductor technologies. This process will enable SFQ circuits to be produced with one million JJs on a chip and achieve a clock frequency greater than 100 GHz.

Superconductor Science and Technology•Feb 15, 2006•62 citations

A simple and robust niobium Josephson junction integrated circuit process

Andrew T. Barfknecht, Rich Ruby, H.L. Ko

A simple and robust process for fabricating low-T/sub c/ Josephson junction integrated circuits has been developed. The process is designed around the Nb/Al/sub 2/O/sub 3/-Al/Nb trilayer, and utilized nine masking steps to form two separate levels of trilayer Josephson junctions, as well as resistors, capacitors, and transmission lines. Materials used for interlayer dielectrics and passivation layers are silicon dioxide and silicon nitride formed by plasma-enhanced chemical vapor deposition (PECVD). The PECVD equipment yields a high deposition rate at moderate substrate temperatures. No degradation of the junction characteristics due to these depositions is seen. The measured loss tangent of this dielectric at 10 GHz using a parallel plate technique is 4.44*10/sup -4/. The dielectric constant of this material is 5.1 in the range of 50 to 400 GHz, measured using an on-chip resonator capacitively coupled to a single shunted Josephson junction. The physical quality of the oxide has been investigated using a variety of tests and has proven to be excellent. A variety of simple circuits using this process technology have been fabricated and tested. More complex circuits are currently under development.

IEEE Transactions on Magnetics•Mar 1, 1991•35 citations

Fabrication Process for Monolithic Integration of a Nitride Superconductor-Based Superconducting Qubit with a Single Flux Quantum Control Circuit

Shigeyuki Miyajima, Taro Yamashita, Masamitsu Tanaka +3 more

We developed a process for fabricating nitride superconductor-based superconducting qubits monolithically integrated with a single flux quantum (SFQ)-based readout and control circuits. Since we used a Josephson junction (JJ) made of an NbN/AlN/NbN tri-layer, including a critical current density (Jc) of 50 A/cm2as the suitable material for superconducting qubits and SFQ readout/control circuits operating at 20 mK, the JJs for both the qubits and the SFQ circuits could simultaneously be fabricated. The device structure was also composed of three superconductive layers, comprising two superconductive layers as wiring layers and other layers as the top ground plane. Then, we used a Pd film as the resistive layer, which is required as the shunt resistors and the bias resistors for the SFQ control circuits, followed by an investigation of the properties of NbN/AlN/NbN epitaxial junctions and evaluation of the sheet inductance of the base NbN and wiring NbTiN layer. Our results showed the successful fabrication of a JJ with a sufficiently low leakage current and aJcof around 50 A/cm2, which was close to the target value. Furthermore, the evaluated sheet inductance exceeded 1 pH, which was several times larger than the values obtained for Nb-integrated circuits.

IEEE Transactions on Applied Superconductivity•Feb 1, 2023•11 citations
We have developed a fabrication technology for superconducting integrated circuits with Nb-based Josephson junctions. The standard fabrication process with 10 mask levels includes 3 Nb superconducting layers and a Mo resistor layer. The influence of deposition parameters on film stress, electrical properties, and surface roughness were studied systematically. High quality Nb, Al, Mo, and SiO2films were successfully deposited for the subsequent fabrication of circuits. The circuit fabrication started with the fabrication of Mo resistors with a target sheet resistanceRshof 2 Ω, followed by the deposition of Nb/Al-AlOx/Nb trilayer Josephson-junction. The target critical current densityJcwas set at 6 kA/cm2. Small-scale circuits such as our standard library cells have been successfully fabricated and tested, confirming the capability of our fabrication technology for superconducting integrated circuits.
Development of 15kA/cm2^22 Fabrication Process for Superconducting Integrated Digital Circuits
A new fabrication process for superconducting integrated digital circuits is reported. We have developed the "SIMIT Nb04" fabrication technique for superconducting integrated circuits with Nb-based Josephson junctions based on the validated "SIMIT Nb03" process and Chemical Mechanical Planarization (CMP) technology. Seven Nb superconducting layers and one Mo resistor layer are included in the "SIMIT Nb04" process with 19 mask levels. The device structure is composed of active layers including junctions at the bottom, two passive transmission line (PTL) layers in the middle and a DC power layer at the top. The circuit fabrication started with the fabrication of Mo resistors with a target sheet resistance Rsh of 3 ΩΩΩ, followed by the deposition of Nb/Al-AlOx_xx​/Nb trilayer Josephson-junction with a target critical current density Jc at 15 kA/cm2^22. To increase the Al-AlOx_xx​ barrier layer etching's repeatability, an additional barrier protection layer was applied. To accomplish high-quality planarization, we created a planarization procedure coupled with dummy filling. To assess the process dependability and controllability, a set of process control monitors (PCMs) for monitoring fabrication and design parameters was designed and monitored. The successful manufacturing and testing of a few small-scale circuits, like our standard library cells, further attests to the viability of our fabrication process for superconducting integrated circuits.
We present the latest development of an Nb/Al-AlOx/Nb Josephson junction fabrication process for superconducting integrated circuits at SIMIT. Our fabrication process has four niobium superconducting layers and one Ti/Pd resistor layer with 1.0 Ω/square sheet resistor for junction shunting and circuit biasing. Critical current density Jcof the junctions is controlled from 30 A/cm2to 10 kA/cm2by exposing aluminum layer to pure or mixed O2atmosphere. Correlation between measured Jcand exposure conditions has been established. Average quality factor (Rsg/Rn) of the junctions in our process is larger than 20 with subgap leakage factor (Vm) beyond 30 mV. Critical current uniformity is obtained according to the switching current (Is) distribution of a 1000-JJ array. Measured standard deviation sigma of Isis less than 4% over the 100-mm wafer. Plasma resonance in a large Josephson junction is used to measure specific capacitance (Cs) of the junction. Sheet inductances of superconducting niobium strip-lines are extracted by a SQUID diagnose circuit and the measured results show good agreement with our design values.
We have developed a 6-kA/cm superconducting integrated circuit fabrication process toward large-scale single flux quantum digital circuits. To evaluate the process reliability and controllability, a set of process control monitors (PCMs) for monitoring fabrication and design parameters was designed and tested. Fabrication parameters, for example, film thicknesses and etched depths of the layers, were measured by testing specific patterns during fabrication. Design parameters such as the critical current density Jc, normal-state resistance Rnand actual sizes of Josephson junctions, the sheet resistance of Mo resistor Rsh, and the penetration depth of Nb films were evaluated by electrically characterizing PCM circuits after fabrication. We also monitored superconducting critical currents for vias and Nb lines, and insulation properties between the metal layers systematically.
The Superconductivity Research Laboratory has successfully fabricated large quantities of single flux quantum (SFQ) large scale integrated circuits, including several thousands of Josephson junctions (JJs). Using a Jc = 2.5 kA cm−2 process in which the number of Nb layers was four and the minimum JJ size was 2 µm square. We developed a new advanced fabrication process that produced a Jc = 10 kA cm−2, nine Nb layers and a minimum JJ size of 1 µm square. The increase in the number of Nb layers was achieved by using a planarization technique. The target of our next generation process is a Jc = 40 kA cm−2 with a 0.5 µm square for the minimum junction size. This specification will be achieved by using advanced semiconductor technologies. This process will enable SFQ circuits to be produced with one million JJs on a chip and achieve a clock frequency greater than 100 GHz.
A simple and robust process for fabricating low-T/sub c/ Josephson junction integrated circuits has been developed. The process is designed around the Nb/Al/sub 2/O/sub 3/-Al/Nb trilayer, and utilized nine masking steps to form two separate levels of trilayer Josephson junctions, as well as resistors, capacitors, and transmission lines. Materials used for interlayer dielectrics and passivation layers are silicon dioxide and silicon nitride formed by plasma-enhanced chemical vapor deposition (PECVD). The PECVD equipment yields a high deposition rate at moderate substrate temperatures. No degradation of the junction characteristics due to these depositions is seen. The measured loss tangent of this dielectric at 10 GHz using a parallel plate technique is 4.44*10/sup -4/. The dielectric constant of this material is 5.1 in the range of 50 to 400 GHz, measured using an on-chip resonator capacitively coupled to a single shunted Josephson junction. The physical quality of the oxide has been investigated using a variety of tests and has proven to be excellent. A variety of simple circuits using this process technology have been fabricated and tested. More complex circuits are currently under development.
We developed a process for fabricating nitride superconductor-based superconducting qubits monolithically integrated with a single flux quantum (SFQ)-based readout and control circuits. Since we used a Josephson junction (JJ) made of an NbN/AlN/NbN tri-layer, including a critical current density (Jc) of 50 A/cm2as the suitable material for superconducting qubits and SFQ readout/control circuits operating at 20 mK, the JJs for both the qubits and the SFQ circuits could simultaneously be fabricated. The device structure was also composed of three superconductive layers, comprising two superconductive layers as wiring layers and other layers as the top ground plane. Then, we used a Pd film as the resistive layer, which is required as the shunt resistors and the bias resistors for the SFQ control circuits, followed by an investigation of the properties of NbN/AlN/NbN epitaxial junctions and evaluation of the sheet inductance of the base NbN and wiring NbTiN layer. Our results showed the successful fabrication of a JJ with a sufficiently low leakage current and aJcof around 50 A/cm2, which was close to the target value. Furthermore, the evaluated sheet inductance exceeded 1 pH, which was several times larger than the values obtained for Nb-integrated circuits.