Quantifying surface losses in superconducting aluminum microwave resonators
Elizabeth Hedrick, Faranak Bahrami, Alexander C. Pakpour-Tabrizi, Atharv Joshi, Q. Rumman Rahman, Ambrose Yang, Ray D. Chang, Matthew P. Bland, Apoorv Jindal, Guangming Cheng, Nan Yao, Robert J. Cava, Andrew A. Houck, Nathalie P. de Leon
quant-phcond-mat.mtrl-sciSubmitted Mar 13, 2026• Announced Mar 16, 2026• 4 citations• Revised Mar 25, 2026 (v2)
The recent realization of millisecond-scale coherence with tantalum-on-silicon transmon qubits showed that depositing the Al/AlOx/Al Josephson junction in a high purity, ultrahigh vacuum environment was critical for achieving lifetime-limited coherence, motivating careful examination of the aluminum surface two-level system (TLS) bath. Here, we measure the microwave absorption arising from surface TLSs in superconducting aluminum resonators, following methodology developed for tantalum resonators. We vary film and surface properties and correlate microwave measurements with materials characterization. We find that the lifetimes of superconducting aluminum resonators are primarily limited by surface losses associated with TLSs in the 2.7 nm-thick native AlOx. Treatment with 49% HF removes surface AlOx completely; however, rapid oxide regrowth limits improvements in surface loss and long term device stability. Using these measurements we estimate that TLSs in aluminum interfaces contribute around 27% of the relaxation rate of state-of-the-art tantalum-on-silicon qubits that incorporate aluminum-based Josephson junctions.
The recent realization of millisecond-scale coherence with tantalum-on-silicon transmon qubits showed that depositing the Al/AlOx/Al Josephson junction in a high purity, ultrahigh vacuum environment was critical for achieving lifetime-limited coherence, motivating careful examination of the aluminum surface two-level system (TLS) bath. Here, we measure the microwave absorption arising from surface TLSs in superconducting aluminum resonators, following methodology developed for tantalum resonators. We vary film and surface properties and correlate microwave measurements with materials characterization. We find that the lifetimes of superconducting aluminum resonators are primarily limited by surface losses associated with TLSs in the 2.7 nm-thick native AlOx. Treatment with 49% HF removes surface AlOx completely; however, rapid oxide regrowth limits improvements in surface loss and long term device stability. Using these measurements we estimate that TLSs in aluminum interfaces contribute around 27% of the relaxation rate of state-of-the-art tantalum-on-silicon qubits that incorporate aluminum-based Josephson junctions.
Superconducting qubits are a leading system for realizing large-scale quantum processors, but overall gate fidelities suffer from coherence times limited by microwave dielectric loss.Recently discovered tantalum-based qubits exhibit record lifetimes exceeding 0.3 ms.Here, we perform systematic, detailed measurements of superconducting tantalum resonators in order to disentangle sources of loss that limit state-of-the-art tantalum devices.By studying the dependence of loss on temperature, microwave photon number, and device geometry, we quantify materials-related losses and observe that the losses are dominated by several types of saturable two-level systems (TLSs), with evidence that both surface and bulk related TLSs contribute to loss.Moreover, we show that surface TLSs can be altered with chemical processing.With four different surface conditions, we quantitatively extract the linear absorption associated with different surface TLS sources.Finally, we quantify the impact of the chemical processing at singlephoton powers, the relevant conditions for qubit device performance.In this regime, we measure resonators with internal quality factors ranging from 5 to 15 × 10 6 , comparable to the best qubits reported.In these devices, the surface and bulk TLS contributions to loss are comparable, showing that systematic improvements in materials on both fronts are necessary to improve qubit coherence further.
Long-term stability of superconducting microwave resonators is essential for scalable quantum technologies; however, surface and interface degradation continue to limit device stability. Here, we demonstrate exceptional stability in microstrip resonators fabricated from epitaxial tantalum and aluminum films, protected by in situ deposited Al2O3 under ultrahigh vacuum. These resonators initially exhibit internal quality factors (Qi) exceeding 106 and maintain high performance with minimal degradation even after fourteen months of air exposure. In contrast, devices relying on native surface oxides show substantial declines in Qi over time, indicating increased microwave losses. X-ray photoelectron spectroscopy reveals that the in situ Al2O3 effectively suppresses interfacial oxidation and preserves the chemical integrity of the underlying superconducting films, whereas native oxides permit progressive oxidation, leading to device degradation. These findings establish a robust, scalable passivation strategy that addresses a longstanding materials challenge in the development of superconducting quantum circuits.
Abstract Quantum bits (qubits) with long coherence times are an important element for the implementation of medium- and large-scale quantum computers. In the case of superconducting planar qubits, understanding and improving qubits’ quality can be achieved by studying superconducting planar resonators. In this paper, we fabricate and characterize coplanar waveguide resonators made from aluminum thin films deposited on silicon substrates. We perform three different substrate surface treatments prior to aluminum deposition: one chemical treatment based on a hydrofluoric acid clean; one physical treatment consisting of a thermal annealing at 880 °C in high vacuum; and one combined treatment comprising both the chemical and the physical treatments. The aim of these treatments is to remove the two-level state (TLS) defects hosted by the native oxides residing at the various samples’ interfaces. We first characterize the fabricated samples through cross-sectional tunneling electron microscopy, acquiring electron energy loss spectroscopy maps of the samples’ cross sections. These measurements show that both the chemical and the physical treatments almost entirely remove native silicon oxide from the substrate surface and that their combination results in the cleanest interface. Additionally, we analyze the effects of the various substrate treatments on the roughness of the silicon surface by means of atomic force microscopy surface morphology mapping. We then study the quality of the resonators by means of microwave measurements in the ‘quantum regime’, i.e., at a temperature T ∼ 10 mK and at a mean microwave photon number 〈 n ph 〉 ∼ 1 . In this regime, we find that both surface treatments independently improve the resonator’s intrinsic quality factor by ≈172%. The highest quality factor is obtained for the combined treatment, Q i ≈ 0.82 million, corresponding to an improvement by ≈256%. Finally, we find that the TLS quality factor averaged over a time period of 3 h is ∼3 million at 〈 n ph 〉 ∼ 10 , indicating that substrate surface engineering can potentially reduce the TLS loss below other losses such as quasiparticle loss and flux noise.
Material losses in superconducting circuits fundamentally limit qubit coherence times and resonator quality factors. Most research efforts focus on mitigating losses at circuit interfaces, including metal--substrate, substrate--air, and metal--air interfaces. However, the correlation between TLS and non-TLS losses with the intrinsic properties of the superconducting metal and the dielectric edge smoothness is not well studied. In this work, we link the aluminum film grain size to non-TLS losses and the dielectric trimming profile and roughness to TLS loss; both loss mechanisms are subsequently mitigated. To reduce metal-related losses, we engineer the aluminum microstructure by heating during deposition, increasing grain size and reducing grain boundary density. Beyond mitigating metal losses, we introduce a two-step etching technique, Tropic etching, to suppress dielectric TLS loss by producing an ultra-smooth silicon surface with minimal defects and redeposition. These results lay out the fabrication pathway for aluminum resonators with lower loss, demonstrating two-orders-of-magnitude improvement in quality factor from 6×104 to 2.3×106. Since aluminum is the basis for most high-coherence Josephson junctions and dielectric edges are inherent to all common device geometries, the improvements in aluminum microstructure and edge profiling, presented here, can enhance the performance of superconducting quantum devices.
Niobium and aluminum have been widely used to realize superconducting resonators and qubits. However, the native oxide at the metal air interface limits the devices results. This layer is highly disordered, and it induces losses limiting the performances of the resonators or qubits. Recently, tantalum led to great improvement in qubit relaxation time. This improvement has been attributed to a thinner and less disordered oxide layer compared to Nb and Al. This study is aimed to limit the formation of the oxide layer, by the introduction of novel superconducting materials such as rhenium or by encapsulating the Nb surface with other superconducting materials such as Ta, Al, Re or other non-superconducting materials such as Au. To better understand the results, we are realizing these studies on coplanar waveguide resonators where the relation between surface losses and quality factor is clear. We are also analyzing different fabrication techniques to completely characterize our devices, linking material properties to the performances. In this work we are also varying the participation ratio of the devices in order to extract with higher fidelity and precision the losses introduced by the involved interfaces.
Aluminum (Al) remains the central material for superconducting qubits, and considerable effort has been devoted to optimizing its deposition and patterning for quantum devices. However, post-processing strategies focused on oxide removal of niobium (Nb) and tantalum (Ta) -based resonators using buffered oxide etch (BOE), which can not be used for Al. This challenge becomes particularly relevant for industry-scale fabrication with multi-chip bonding, where delays between sample preparation and cooldown require surface treatments that preserve low dielectric loss during extended exposure to ambient conditions. In this work, we investigate surface modification approaches for Al resonators subjected to a 24-hour delay prior to cryogenic measurement. Passivation using self-limiting oxygen and fluorine chemistries was evaluated utilizing different plasma processes. Remote oxygen plasma treatment reduced dielectric losses, in contrast to direct oxygen plasma. A fluorine-based plasma process was developed that passivated the Al surface for subsequent BOE treatment. However, the fluorine content in the surface resulted in higher loss, identifying fluorine as an unsuitable passivation material for Al resonators. Above all, selective oxide removal using HF (hydrogen fluoride) vapor and phosphoric acid yielded median dielectric losses as low as δ~LP=5.7×10−7 (QLP≈1.7M) with δ~TLS=3.6×10−7 (QTLS≈2.8M) in the single photon regime. Selective oxide removal provides a promising pathway for robust Al-based qubit fabrication, as it preserves low dielectric losses for a 24-hour delay before cooldown.