Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2607.22265

Low loss superconducting resonators enabled by aluminum microstructural engineering and dielectric trimming

Mahmoud Almansouri, Umar T. F. Alhuwaymel, Ibraheem AlYousef, Albaraa Shafi, Abdullah Albogime, Igor Getmanov, Ahmed Hajr, Atif Shamim

quant-phSubmitted Jul 24, 2026• Announced Jul 27, 2026• 1 citation• Revised Jul 28, 2026 (v2)
v1 · Jul 24, 2026v2 · Jul 28, 2026
arXivHTMLPDF

Abstract

Material losses in superconducting circuits fundamentally limit qubit coherence times and resonator quality factors. Most research efforts focus on mitigating losses at circuit interfaces, including metal--substrate, substrate--air, and metal--air interfaces. However, the correlation between TLS and non-TLS losses with the intrinsic properties of the superconducting metal and the dielectric edge smoothness is not well studied. In this work, we link the aluminum film grain size to non-TLS losses and the dielectric trimming profile and roughness to TLS loss; both loss mechanisms are subsequently mitigated. To reduce metal-related losses, we engineer the aluminum microstructure by heating during deposition, increasing grain size and reducing grain boundary density. Beyond mitigating metal losses, we introduce a two-step etching technique, Tropic etching, to suppress dielectric TLS loss by producing an ultra-smooth silicon surface with minimal defects and redeposition. These results lay out the fabrication pathway for aluminum resonators with lower loss, demonstrating two-orders-of-magnitude improvement in quality factor from $6\times10^{4}$ to $2.3\times10^{6}$. Since aluminum is the basis for most high-coherence Josephson junctions and dielectric edges are inherent to all common device geometries, the improvements in aluminum microstructure and edge profiling, presented here, can enhance the performance of superconducting quantum devices.

Related papers

High-Q trenched aluminum coplanar resonators with an ultrasonic edge microcutting for superconducting quantum devices

E. V. Zikiy, A. I. Ivanov, Nikita S. Smirnov +7 more

Abstract Dielectric losses are one of the key factors limiting the coherence of superconducting qubits. The impact of materials and fabrication steps on dielectric losses can be evaluated using coplanar waveguide (CPW) microwave resonators. Here, we report on superconducting CPW microwave resonators with internal quality factors systematically exceeding 5 × 106 at high powers and 2 × 106 (with the best value of 4.4 × 106) at low power. Such performance is demonstrated for 100-nm-thick aluminum resonators with 7–10.5 um center trace on high-resistivity silicon substrates commonly used in Josephson-junction based quantum circuit. We investigate internal quality factors of the resonators with both dry and wet aluminum etching, as well as deep and isotropic reactive ion etching of silicon substrate. Josephson junction compatible CPW resonators fabrication process with both airbridges and silicon substrate etching is proposed. Finally, we demonstrate the effect of airbridges’ positions and extra process steps on the overall dielectric losses. The best quality factors are obtained for the wet etched aluminum resonators and isotropically removed substrate with the proposed ultrasonic metal edge microcutting.

arXiv:2306.16301•Scientific Reports•Sep 20, 2023•35 citations

Comparison of dielectric loss in titanium nitride and aluminum superconducting resonators

Alexander J. Melville, Greg Calusine, Wayne H. Woods +8 more

Lossy dielectrics are a significant source of decoherence in superconducting quantum circuits. In this report, we model and compare the dielectric loss in bulk and interfacial dielectrics in titanium nitride (TiN) and aluminum (Al) superconducting coplanar waveguide resonators. We fabricate isotropically trenched resonators to produce a series of device geometries that accentuate a specific dielectric region's contribution to the resonator quality factor. While each dielectric region contributes significantly to loss in TiN devices, the metal–air interface dominates the loss in the Al devices. Furthermore, we evaluate the quality factor of each TiN resonator geometry with and without a post-process hydrofluoric etch and find that it reduced losses from the substrate–air interface, thereby improving the quality factor.

arXiv:2007.07338•Applied Physics Letters•Sep 21, 2020•76 citations

Characterization of process-related interfacial dielectric loss in aluminum-on-silicon by resonator microwave measurements, materials analysis, and imaging

Lert Chayanun, Janka Biznárová, Lunjie J. Zeng +10 more

We systematically investigate the influence of the fabrication process on dielectric loss in aluminum-on-silicon superconducting coplanar waveguide resonators with internal quality factors (Qi) of about one million at the single-photon level. These devices are essential components in superconducting quantum processors; they also serve as proxies for understanding the energy loss of superconducting qubits. By systematically varying several fabrication steps, we identify the relative importance of reducing loss at the substrate–metal and substrate–air interfaces. We find that it is essential to clean the silicon substrate in hydrogen fluoride (HF) prior to aluminum deposition. A post-fabrication removal of the oxides on the surface of the silicon substrate and the aluminum film by immersion in HF further improves the Qi. We observe a small, but noticeable, adverse effect on the loss by omitting either standard cleaning (SC1), pre-deposition heating of the substrate to 300 °C, or in situ post-deposition oxidation of the film’s top surface. We find no improvement due to excessive pumping meant to reach a background pressure below 6 × 10−8 mbar. We correlate the measured loss with microscopic properties of the substrate–metal interface through characterization with x-ray photoelectron spectroscopy, time-of-flight secondary ion mass spectrometry, transmission electron microscopy, energy-dispersive x-ray spectroscopy, and atomic force microscopy.

arXiv:2403.00723•APL Quantum•Jun 1, 2024•15 citations

Improving the Lifetime of Aluminum-Based Superconducting Qubits through Atomic Layer Etching and Deposition

Neha Mahuli, Joaquín Minguzzi, Jiansong Gao +9 more

We present a dry surface treatment combining atomic layer etching and deposition (ALE and ALD) to mitigate dielectric loss in fully fabricated superconducting quantum devices formed from aluminum thin films on silicon. The treatment, performed as a final processing step prior to device packaging, starts by conformally removing the native metal oxide and fabrication residues from the exposed surfaces through ALE, before in situ encapsulating the metal surfaces with a thin dielectric layer using ALD. We measure a 2-fold reduction in loss attributed to two-level system (TLS) absorption in treated aluminum-based resonators and planar transmon qubits. Treated transmons with compact capacitor plates and gaps achieve median transmon quality factor ( Q ) and transmon qubit energy relaxation time ( T 1 ) values of 3.69 ± 0.42 × 10 6 and 196 ± 22 μs, respectively. These improvements were found to be sustained over several months. We discuss how the combination of ALE and ALD reverses fabrication-induced surface damage to significantly and durably improve device performance via a reduction of the TLS defect density in the capacitive elements.

arXiv:2506.17474•ACS Nano•Nov 20, 2025•10 citations

Material and Interface Engineering Strategies to Mitigate Decoherence in Superconducting Qubits

Dominic P. Goronzy, Anthony McFadden, David A. Garcia Wetten +16 more

While significant strides have been made to increase the coherence time of superconducting qubits, further advancements are essential for realizing scalable quantum computing. Decoherence is often a result of loss and noise stemming from two-level systems and excess quasiparticles, arising due to material defects, fabrication processes, and ambient exposure, particularly at surfaces and interfaces. Our recent efforts to mitigate these decoherence mechanisms have employed a variety of strategies, including low-loss surface encapsulation materials, advanced substrate preparation techniques, modifications to metal film growth, and the development of novel fabrication processes. The structural and chemical properties of materials, surfaces, and interfaces are studied using scanning probe microscopy, electron microscopy, photoelectron spectroscopy, mass spectrometry, and X-ray diffraction, which is correlated to device performance metrics, including superconducting resonator internal quality factor and qubit T1 time. This information is used to identify and understand material sources of loss and their origins in the device fabrication process. Through multi-institution efforts within SQMS we have identified the loss mechanism of interstitial hydrogen in niobium-based devices and shown how standard fabrication processes introduce these hydrides, developing strategies to mitigate their formation.1 Furthermore, we have characterized the metal-substrate interface, including the loss of niobium-silicides formed at that interface, and developed silicon surface treatments that reduce atomic scale roughness and oxygen content at the metal-substrate and Josephson junction interfaces.2-4 By developing the connection between materials properties and the overall performance of superconducting quantum circuitry, we can develop fabrication strategies to mitigate material losses, thus supporting the ongoing efforts to enhance coherence time in superconducting quantum devices. 1. Torres-Castanedo, C. G.*, Goronzy, D. P.*, et al., Adv. Funct. Mater., 2401365 (2024) 2. Lu, X., et al., Phys. Rev. Materials 6, 064402 (2022) 3. Berti, G., Appl. Phys. Lett. 122, 192605 (2023) 4. Kopas, C. J., Goronzy, D. P., et al., arXiv:2408.02863 (2024)

•Sep 23, 2024•0 citations

Substrate surface engineering for high-quality silicon/aluminum superconducting resonators

C T Earnest, J. H. Béjanin, T G McConkey +4 more

Abstract Quantum bits (qubits) with long coherence times are an important element for the implementation of medium- and large-scale quantum computers. In the case of superconducting planar qubits, understanding and improving qubits’ quality can be achieved by studying superconducting planar resonators. In this paper, we fabricate and characterize coplanar waveguide resonators made from aluminum thin films deposited on silicon substrates. We perform three different substrate surface treatments prior to aluminum deposition: one chemical treatment based on a hydrofluoric acid clean; one physical treatment consisting of a thermal annealing at 880 °C in high vacuum; and one combined treatment comprising both the chemical and the physical treatments. The aim of these treatments is to remove the two-level state (TLS) defects hosted by the native oxides residing at the various samples’ interfaces. We first characterize the fabricated samples through cross-sectional tunneling electron microscopy, acquiring electron energy loss spectroscopy maps of the samples’ cross sections. These measurements show that both the chemical and the physical treatments almost entirely remove native silicon oxide from the substrate surface and that their combination results in the cleanest interface. Additionally, we analyze the effects of the various substrate treatments on the roughness of the silicon surface by means of atomic force microscopy surface morphology mapping. We then study the quality of the resonators by means of microwave measurements in the ‘quantum regime’, i.e., at a temperature T ∼ 10 mK and at a mean microwave photon number 〈 n ph 〉 ∼ 1 . In this regime, we find that both surface treatments independently improve the resonator’s intrinsic quality factor by ≈172%. The highest quality factor is obtained for the combined treatment, Q i ≈ 0.82 million, corresponding to an improvement by ≈256%. Finally, we find that the TLS quality factor averaged over a time period of 3 h is ∼3 million at 〈 n ph 〉 ∼ 10 , indicating that substrate surface engineering can potentially reduce the TLS loss below other losses such as quasiparticle loss and flux noise.

arXiv:1807.08072•Superconductor Science and Technology•Oct 1, 2018•77 citations
Material losses in superconducting circuits fundamentally limit qubit coherence times and resonator quality factors. Most research efforts focus on mitigating losses at circuit interfaces, including metal--substrate, substrate--air, and metal--air interfaces. However, the correlation between TLS and non-TLS losses with the intrinsic properties of the superconducting metal and the dielectric edge smoothness is not well studied. In this work, we link the aluminum film grain size to non-TLS losses and the dielectric trimming profile and roughness to TLS loss; both loss mechanisms are subsequently mitigated. To reduce metal-related losses, we engineer the aluminum microstructure by heating during deposition, increasing grain size and reducing grain boundary density. Beyond mitigating metal losses, we introduce a two-step etching technique, Tropic etching, to suppress dielectric TLS loss by producing an ultra-smooth silicon surface with minimal defects and redeposition. These results lay out the fabrication pathway for aluminum resonators with lower loss, demonstrating two-orders-of-magnitude improvement in quality factor from 6×1046\times10^{4}6×104 to 2.3×1062.3\times10^{6}2.3×106. Since aluminum is the basis for most high-coherence Josephson junctions and dielectric edges are inherent to all common device geometries, the improvements in aluminum microstructure and edge profiling, presented here, can enhance the performance of superconducting quantum devices.
Abstract Dielectric losses are one of the key factors limiting the coherence of superconducting qubits. The impact of materials and fabrication steps on dielectric losses can be evaluated using coplanar waveguide (CPW) microwave resonators. Here, we report on superconducting CPW microwave resonators with internal quality factors systematically exceeding 5 × 106 at high powers and 2 × 106 (with the best value of 4.4 × 106) at low power. Such performance is demonstrated for 100-nm-thick aluminum resonators with 7–10.5 um center trace on high-resistivity silicon substrates commonly used in Josephson-junction based quantum circuit. We investigate internal quality factors of the resonators with both dry and wet aluminum etching, as well as deep and isotropic reactive ion etching of silicon substrate. Josephson junction compatible CPW resonators fabrication process with both airbridges and silicon substrate etching is proposed. Finally, we demonstrate the effect of airbridges’ positions and extra process steps on the overall dielectric losses. The best quality factors are obtained for the wet etched aluminum resonators and isotropically removed substrate with the proposed ultrasonic metal edge microcutting.
Lossy dielectrics are a significant source of decoherence in superconducting quantum circuits. In this report, we model and compare the dielectric loss in bulk and interfacial dielectrics in titanium nitride (TiN) and aluminum (Al) superconducting coplanar waveguide resonators. We fabricate isotropically trenched resonators to produce a series of device geometries that accentuate a specific dielectric region's contribution to the resonator quality factor. While each dielectric region contributes significantly to loss in TiN devices, the metal–air interface dominates the loss in the Al devices. Furthermore, we evaluate the quality factor of each TiN resonator geometry with and without a post-process hydrofluoric etch and find that it reduced losses from the substrate–air interface, thereby improving the quality factor.
We systematically investigate the influence of the fabrication process on dielectric loss in aluminum-on-silicon superconducting coplanar waveguide resonators with internal quality factors (Qi) of about one million at the single-photon level. These devices are essential components in superconducting quantum processors; they also serve as proxies for understanding the energy loss of superconducting qubits. By systematically varying several fabrication steps, we identify the relative importance of reducing loss at the substrate–metal and substrate–air interfaces. We find that it is essential to clean the silicon substrate in hydrogen fluoride (HF) prior to aluminum deposition. A post-fabrication removal of the oxides on the surface of the silicon substrate and the aluminum film by immersion in HF further improves the Qi. We observe a small, but noticeable, adverse effect on the loss by omitting either standard cleaning (SC1), pre-deposition heating of the substrate to 300 °C, or in situ post-deposition oxidation of the film’s top surface. We find no improvement due to excessive pumping meant to reach a background pressure below 6 × 10−8 mbar. We correlate the measured loss with microscopic properties of the substrate–metal interface through characterization with x-ray photoelectron spectroscopy, time-of-flight secondary ion mass spectrometry, transmission electron microscopy, energy-dispersive x-ray spectroscopy, and atomic force microscopy.
We present a dry surface treatment combining atomic layer etching and deposition (ALE and ALD) to mitigate dielectric loss in fully fabricated superconducting quantum devices formed from aluminum thin films on silicon. The treatment, performed as a final processing step prior to device packaging, starts by conformally removing the native metal oxide and fabrication residues from the exposed surfaces through ALE, before in situ encapsulating the metal surfaces with a thin dielectric layer using ALD. We measure a 2-fold reduction in loss attributed to two-level system (TLS) absorption in treated aluminum-based resonators and planar transmon qubits. Treated transmons with compact capacitor plates and gaps achieve median transmon quality factor ( Q ) and transmon qubit energy relaxation time ( T 1 ) values of 3.69 ± 0.42 × 10 6 and 196 ± 22 μs, respectively. These improvements were found to be sustained over several months. We discuss how the combination of ALE and ALD reverses fabrication-induced surface damage to significantly and durably improve device performance via a reduction of the TLS defect density in the capacitive elements.
While significant strides have been made to increase the coherence time of superconducting qubits, further advancements are essential for realizing scalable quantum computing. Decoherence is often a result of loss and noise stemming from two-level systems and excess quasiparticles, arising due to material defects, fabrication processes, and ambient exposure, particularly at surfaces and interfaces. Our recent efforts to mitigate these decoherence mechanisms have employed a variety of strategies, including low-loss surface encapsulation materials, advanced substrate preparation techniques, modifications to metal film growth, and the development of novel fabrication processes. The structural and chemical properties of materials, surfaces, and interfaces are studied using scanning probe microscopy, electron microscopy, photoelectron spectroscopy, mass spectrometry, and X-ray diffraction, which is correlated to device performance metrics, including superconducting resonator internal quality factor and qubit T1 time. This information is used to identify and understand material sources of loss and their origins in the device fabrication process. Through multi-institution efforts within SQMS we have identified the loss mechanism of interstitial hydrogen in niobium-based devices and shown how standard fabrication processes introduce these hydrides, developing strategies to mitigate their formation.1 Furthermore, we have characterized the metal-substrate interface, including the loss of niobium-silicides formed at that interface, and developed silicon surface treatments that reduce atomic scale roughness and oxygen content at the metal-substrate and Josephson junction interfaces.2-4 By developing the connection between materials properties and the overall performance of superconducting quantum circuitry, we can develop fabrication strategies to mitigate material losses, thus supporting the ongoing efforts to enhance coherence time in superconducting quantum devices. 1. Torres-Castanedo, C. G.*, Goronzy, D. P.*, et al., Adv. Funct. Mater., 2401365 (2024) 2. Lu, X., et al., Phys. Rev. Materials 6, 064402 (2022) 3. Berti, G., Appl. Phys. Lett. 122, 192605 (2023) 4. Kopas, C. J., Goronzy, D. P., et al., arXiv:2408.02863 (2024)
Abstract Quantum bits (qubits) with long coherence times are an important element for the implementation of medium- and large-scale quantum computers. In the case of superconducting planar qubits, understanding and improving qubits’ quality can be achieved by studying superconducting planar resonators. In this paper, we fabricate and characterize coplanar waveguide resonators made from aluminum thin films deposited on silicon substrates. We perform three different substrate surface treatments prior to aluminum deposition: one chemical treatment based on a hydrofluoric acid clean; one physical treatment consisting of a thermal annealing at 880 °C in high vacuum; and one combined treatment comprising both the chemical and the physical treatments. The aim of these treatments is to remove the two-level state (TLS) defects hosted by the native oxides residing at the various samples’ interfaces. We first characterize the fabricated samples through cross-sectional tunneling electron microscopy, acquiring electron energy loss spectroscopy maps of the samples’ cross sections. These measurements show that both the chemical and the physical treatments almost entirely remove native silicon oxide from the substrate surface and that their combination results in the cleanest interface. Additionally, we analyze the effects of the various substrate treatments on the roughness of the silicon surface by means of atomic force microscopy surface morphology mapping. We then study the quality of the resonators by means of microwave measurements in the ‘quantum regime’, i.e., at a temperature T ∼ 10 mK and at a mean microwave photon number 〈 n ph 〉 ∼ 1 . In this regime, we find that both surface treatments independently improve the resonator’s intrinsic quality factor by ≈172%. The highest quality factor is obtained for the combined treatment, Q i ≈ 0.82 million, corresponding to an improvement by ≈256%. Finally, we find that the TLS quality factor averaged over a time period of 3 h is ∼3 million at 〈 n ph 〉 ∼ 10 , indicating that substrate surface engineering can potentially reduce the TLS loss below other losses such as quasiparticle loss and flux noise.