Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2602.00390 · Quantum Science and Technology

Wafer-scale micro-knife sealed vacuum cells for quantum devices

Megan Kelleher, Konrad Ziegler, Jeremy Robin, Lianxin Huang, Mitchel Button, Liam Mauck, Judith Olson, Peter D. Brewer, Danny Kim, John E. Kitching, Ruwan Senaratne, William McGehee, Travis M. Autry

Published Jul 16, 2026• 1 citation
arXivHTMLPDF

Abstract

Abstract Advanced integration technologies greatly enhance the prospects and reliability of practical quantum sensors, atomic clocks, and quantum information technologies. The performance and proliferation of these devices at chip scale is contingent upon developing low leak and low gas permeation vacuum cells using wafer-scale techniques. Here, we demonstrate a novel, low-leak-rate micro-knife bonding approach, enabling the realization of both atomic vapor cells and more complex evacuated atomic beam devices. These devices are fabricated using selective laser etching in a fused silica platform. The vapor cells are mechanically robust exhibiting shear-force strength ∼ 15 MPa, demonstrate long lifetimes ( > 1 year), low residual gas pressures ( ≪ 10 − 3 mbar ) , and leak rates below fine-leak testing sensitivity ( ≪ 2.8 × 10 − 10 mbar ⋅ l s − 1 ). Micro-knife bonding greatly simplifies the fabrication process for complex chip scale atom-beam devices and atomic vapor cells while identifying a path to future chip-scale cold atom devices, improved chip scale atomic clocks, and fieldable dissipation-dilution-limited optomechanics.

DOI
10.1088/2058-9565/ae8bd3

Related papers

Wafer-scale fabrication of alkali vapor cells

Yang Li, Marlou R. Slot, Dongyu Sohn +3 more

This paper describes the progress made in developing wafer-scale fabrication process of alkali vapor cells for chip-scale atomic devices such as Coherent Population Trapping (CPT) clocks, optical frequency standards and Rydberg-atom-based sensors. The wafer level fabrication process uses anodic bonding and introduces alkali atoms by chemical reactions of Alkali Chloride with Barium Azide. This method is compatible to make cells with a wide range of buffer gas species and pressures, including evacuated cells. We improve the yield of the cells to above 50%. We will show the residual gas pressures for evacuated cells are mostly consistent with zero within the resolution of the saturation absorption spectroscopy measurement. The temperature coefficients for the CPT spectroscopy are improved with Ar-N2 mixture buffer gas compared with only N2 buffer gas.

Optical and Quantum Sensing and Precision Metrology II•Mar 19, 2025•0 citations

The Microfabricated Alkali Vapor Cell with High Hermeticity for Chip-Scale Atomic Clock

Shuo Jia, Zhiyuan Jiang, Binbin Jiao +4 more

Herein, a microfabricated millimeter-level vapor alkali cell with a high hermeticity is fabricated through a wet etching and single-chip anodic bonding process. The vapor cell, containing Rb and N2, was investigated in a coherent population trapping (CPT) setup for the application of a chip-scale atomic clock (CSAC). The contrast of CPT resonance is up to 1.1% within the only 1 mm length of light interacting with atom. The effects of some critical external parameters on the CPT resonance, such as laser intensity, cell temperature, and buffer gas pressure, are thoroughly studied and optimized. The improved microfabricated vapor cell also exhibited great potential for other chip-scale atomic devices.

Applied Sciences•Jan 3, 2022•21 citations

Wafer-scale fabrication of evacuated alkali vapor cells

Yang Li, Donggyu B. Sohn, Matthew T. Hummon +2 more

We describe a process for fabricating a wafer-scale array of alkali metal vapor cells with low residual gas pressure. We show that by etching long, thin channels between the cells on the Si wafer surface, the residual gas pressure in the evacuated vapor cell can be reduced to below 0.5 kPa (4 Torr) with a yield above 50%. The low residual gas pressure in these mass-producible alkali vapor cells can enable a new generation of low-cost chip-scale atomic devices such as vapor cell optical clocks, wavelength references, and Rydberg sensors.

arXiv:2405.11088•Optics Letters•Aug 14, 2024•12 citations

Micro-fabricated Alkali Vapor Cells for Chip Scale Atomic Clocks Sealed at Low Temperature with Thin-Film Metallic Bonding

Rahel Strässle, Matthieu Pellaton, Yves Pétremand +4 more

Micro-fabriced alkali vapor cells and applications in various fields as the heart of ultraprecise sensors, like chip scale atomic clocks, magnetometers or gyroscopes. Miniaturization asks for either new fabrication techniques or new physical concepts or both. We present here a new fabrication technique for the alkali cells which allows the integration of a anti-relaxation wall coating for alkali vapor cells in order to improve the signal for miniazurized cells.

•Jan 1, 2013•0 citations

COMS-Integrated Atomic Vapor Cells with Ultra-long Optical Access for Highly Sensitive and Scalable Quantum Sensors

Yintao Ma, Yao Chen, Mingzhi Yu +6 more

The most appealing features of chip-scale quantum sensors are their capability to maintain extreme sensitivity while enabling large-scale batch manufacturing. This necessitates high-level integration and wafer-level fabrication of atomic vapor cells. In this paper, we describe a micromachining paradigm for wafer-level atomic vapor cells functionalized by CMOS-compatible non-magnetic heaters and temperature sensors and demonstrate several innovative applications. Leveraging standard micro-nanofabrication technology, the integrated vapor cells achieved an ultra-long optical access of 5 mm, nearly four time that of previously microfabricated vapor cells. The feasibility of the integrated atomic vapor cells fabrication process was verified by a consecutive 30-day aging test in a harsh environment (operating temperature of 473 K and vacuum of approximately 1 Pa). Benefiting from the ultra-long optical path, we observed several typical quantum effects, including the saturation absorption and spin fluctuations, a regime previously inaccessible with conventional micromachined vapor cells. Finally, a zero-field quantum magnetometry with an ultra-high magnetic sensitivity of 12 fT/Hz1/2 was also demonstrated. Our achievements broaden the potential applications of microfabricated atomic vapor cells and pave the way for scalable manufacturing of ultrasensitive, chip-scale quantum sensors.

arXiv:2507.05993•Jul 8, 2025•0 citations

Wafer‐scale integration of photonic integrated circuits and atomic vapor cells

Arieh Grosman, Roy Zektzer, Noa Mazurski +2 more

Atom-based technologies have played a central role in both fundamental research and application-driven developments. For example, devices such as atomic clocks and magnetometers are essential for precision time-keeping, navigation, and sensing. However, many of these demonstrations remain confined to laboratory settings due to their reliance on bulky equipment and centimeter-scale atomic vapor cells. In recent years, significant efforts have been made to miniaturize these vapor cells to enable field-deployable systems. Yet, integrating these cells with the necessary photonic components remains a complex and non-scalable process. To address this challenge, we have introduced the atomic-cladded waveguide (ACWG) architecture, which enables the integration of atomic and photonic functions on the same chip. While the ACWG concept provides a significant step forward toward integration, there is still a significant gap related to wafer scale manufacturability. In particular, previous demonstrations of atomic-photonic integration have relied on manual assembly of vapor cells onto single chips, restricting miniaturization, manufacturability, and thermal robustness. To revolutionize manufacturability of these devices, we hereby demonstrate our new generation of ACWG devices that overcomes these constraints. The approach is based on wafer bonding of a silicon wafer - consisting of multiple photonic chips to a glass wafer with pre-etched atomic chambers. This wafer-scale process yields multiple miniaturized integrated photonic-atomic chips in a single batch. The bonded devices operate reliably at elevated temperatures over an extended period of time, allowing higher atomic densities to be used. The fabrication method consists of well-defined, repeatable steps, paving the way for scalable production of mature integrated photonic-atomic systems for next-generation sensing, metrology, and quantum technologies, inspired by commercial complementary metal-oxide-semiconductor-based processes.

Nanophotonics•Dec 1, 2025•8 citations
Abstract Advanced integration technologies greatly enhance the prospects and reliability of practical quantum sensors, atomic clocks, and quantum information technologies. The performance and proliferation of these devices at chip scale is contingent upon developing low leak and low gas permeation vacuum cells using wafer-scale techniques. Here, we demonstrate a novel, low-leak-rate micro-knife bonding approach, enabling the realization of both atomic vapor cells and more complex evacuated atomic beam devices. These devices are fabricated using selective laser etching in a fused silica platform. The vapor cells are mechanically robust exhibiting shear-force strength ∼ 15 MPa, demonstrate long lifetimes ( > 1 year), low residual gas pressures ( ≪ 10 − 3 mbar ) , and leak rates below fine-leak testing sensitivity ( ≪ 2.8 × 10 − 10 mbar ⋅ l s − 1 ). Micro-knife bonding greatly simplifies the fabrication process for complex chip scale atom-beam devices and atomic vapor cells while identifying a path to future chip-scale cold atom devices, improved chip scale atomic clocks, and fieldable dissipation-dilution-limited optomechanics.
This paper describes the progress made in developing wafer-scale fabrication process of alkali vapor cells for chip-scale atomic devices such as Coherent Population Trapping (CPT) clocks, optical frequency standards and Rydberg-atom-based sensors. The wafer level fabrication process uses anodic bonding and introduces alkali atoms by chemical reactions of Alkali Chloride with Barium Azide. This method is compatible to make cells with a wide range of buffer gas species and pressures, including evacuated cells. We improve the yield of the cells to above 50%. We will show the residual gas pressures for evacuated cells are mostly consistent with zero within the resolution of the saturation absorption spectroscopy measurement. The temperature coefficients for the CPT spectroscopy are improved with Ar-N2 mixture buffer gas compared with only N2 buffer gas.
Herein, a microfabricated millimeter-level vapor alkali cell with a high hermeticity is fabricated through a wet etching and single-chip anodic bonding process. The vapor cell, containing Rb and N2, was investigated in a coherent population trapping (CPT) setup for the application of a chip-scale atomic clock (CSAC). The contrast of CPT resonance is up to 1.1% within the only 1 mm length of light interacting with atom. The effects of some critical external parameters on the CPT resonance, such as laser intensity, cell temperature, and buffer gas pressure, are thoroughly studied and optimized. The improved microfabricated vapor cell also exhibited great potential for other chip-scale atomic devices.
We describe a process for fabricating a wafer-scale array of alkali metal vapor cells with low residual gas pressure. We show that by etching long, thin channels between the cells on the Si wafer surface, the residual gas pressure in the evacuated vapor cell can be reduced to below 0.5 kPa (4 Torr) with a yield above 50%. The low residual gas pressure in these mass-producible alkali vapor cells can enable a new generation of low-cost chip-scale atomic devices such as vapor cell optical clocks, wavelength references, and Rydberg sensors.
The most appealing features of chip-scale quantum sensors are their capability to maintain extreme sensitivity while enabling large-scale batch manufacturing. This necessitates high-level integration and wafer-level fabrication of atomic vapor cells. In this paper, we describe a micromachining paradigm for wafer-level atomic vapor cells functionalized by CMOS-compatible non-magnetic heaters and temperature sensors and demonstrate several innovative applications. Leveraging standard micro-nanofabrication technology, the integrated vapor cells achieved an ultra-long optical access of 5 mm, nearly four time that of previously microfabricated vapor cells. The feasibility of the integrated atomic vapor cells fabrication process was verified by a consecutive 30-day aging test in a harsh environment (operating temperature of 473 K and vacuum of approximately 1 Pa). Benefiting from the ultra-long optical path, we observed several typical quantum effects, including the saturation absorption and spin fluctuations, a regime previously inaccessible with conventional micromachined vapor cells. Finally, a zero-field quantum magnetometry with an ultra-high magnetic sensitivity of 12 fT/Hz1/2 was also demonstrated. Our achievements broaden the potential applications of microfabricated atomic vapor cells and pave the way for scalable manufacturing of ultrasensitive, chip-scale quantum sensors.
Atom-based technologies have played a central role in both fundamental research and application-driven developments. For example, devices such as atomic clocks and magnetometers are essential for precision time-keeping, navigation, and sensing. However, many of these demonstrations remain confined to laboratory settings due to their reliance on bulky equipment and centimeter-scale atomic vapor cells. In recent years, significant efforts have been made to miniaturize these vapor cells to enable field-deployable systems. Yet, integrating these cells with the necessary photonic components remains a complex and non-scalable process. To address this challenge, we have introduced the atomic-cladded waveguide (ACWG) architecture, which enables the integration of atomic and photonic functions on the same chip. While the ACWG concept provides a significant step forward toward integration, there is still a significant gap related to wafer scale manufacturability. In particular, previous demonstrations of atomic-photonic integration have relied on manual assembly of vapor cells onto single chips, restricting miniaturization, manufacturability, and thermal robustness. To revolutionize manufacturability of these devices, we hereby demonstrate our new generation of ACWG devices that overcomes these constraints. The approach is based on wafer bonding of a silicon wafer - consisting of multiple photonic chips to a glass wafer with pre-etched atomic chambers. This wafer-scale process yields multiple miniaturized integrated photonic-atomic chips in a single batch. The bonded devices operate reliably at elevated temperatures over an extended period of time, allowing higher atomic densities to be used. The fabrication method consists of well-defined, repeatable steps, paving the way for scalable production of mature integrated photonic-atomic systems for next-generation sensing, metrology, and quantum technologies, inspired by commercial complementary metal-oxide-semiconductor-based processes.