Traveling-wave parametric amplifiers (TWPAs) have attracted much attention for their broadband amplification and near-quantum-limited noise performance. TWPAs are nonreciprocal by nature providing gain for forward-propagating signals and transmission line losses for backward traveling waves. This intrinsic nonreciprocity is insufficient to protect sensitive quantum devices from backaction due to noise from warmer amplification stages in practical systems, and requires the use of bulky cryogenic isolators. We present a multistage TWPA (mTWPA) that addresses this limitation by achieving passive in-band reverse isolation alongside near-quantum-limited noise performance. The multistage architecture consists of two mode conversion stages and a reflectionless high-pass filter that provides the passive isolation. Experimental measurements of a prototype mTWPA demonstrated 20 dB of forward gain across a 1.6 GHz bandwidth and greater than 35 dB of reverse isolation. Noise measurements indicate performance at 1.7 times the quantum limit. This demonstrates that the increased complexity of a multistage TWPA design does not lead to significant added noise. The designed distribution of gain across the stages is engineered to minimize internal amplifier noise at the input, and we propose further optimization strategies in redistribution of the gain between the stages. This level of isolation mitigates noise from warmer amplification stages, matching the performance of conventional isolators. The passive reverse isolation of the mTWPA, allows for the amplifier to operate in pulsed mode where the amplifier is off during qubit gate operations and is turned on during readout allowing for an isolator free scalable readout architecture.
Traveling-wave parametric amplifiers (TWPAs) have attracted much attention for their broadband amplification and near-quantum-limited noise performance. TWPAs are nonreciprocal by nature providing gain for forward-propagating signals and transmission line losses for backward traveling waves. This intrinsic nonreciprocity is insufficient to protect sensitive quantum devices from backaction due to noise from warmer amplification stages in practical systems, and requires the use of bulky cryogenic isolators. We present a multistage TWPA (mTWPA) that addresses this limitation by achieving passive in-band reverse isolation alongside near-quantum-limited noise performance. The multistage architecture consists of two mode conversion stages and a reflectionless high-pass filter that provides the passive isolation. Experimental measurements of a prototype mTWPA demonstrated 20 dB of forward gain across a 1.6 GHz bandwidth and greater than 35 dB of reverse isolation. Noise measurements indicate performance at 1.7 times the quantum limit. This demonstrates that the increased complexity of a multistage TWPA design does not lead to significant added noise. The designed distribution of gain across the stages is engineered to minimize internal amplifier noise at the input, and we propose further optimization strategies in redistribution of the gain between the stages. This level of isolation mitigates noise from warmer amplification stages, matching the performance of conventional isolators. The passive reverse isolation of the mTWPA, allows for the amplifier to operate in pulsed mode where the amplifier is off during qubit gate operations and is turned on during readout allowing for an isolator free scalable readout architecture.
Superconducting traveling-wave parametric amplifiers (TWPA) have emerged as highly versatile devices, offering broadband amplification with quantum-limited noise performance. They hold significant potential for addressing the readout bottleneck in prototype quantum computers, enabling scalability. Key challenges with this technology include achieving sufficient gain with minimal gain ripple while maintaining low noise performance. Efficient phase matching between a weak signal and a strong pump over the entire length of the TWPA is critical to overcoming these challenges. We present an experimental demonstration of the inverse Kerr phase matching technique in a TWPA, first proposed in Ref. Phys. Rev. Appl. 4, 024014. This method addresses several limitations of conventional dispersion engineering approaches of phase matching in the four-wave mixing parametric process in TWPAs. Most notably the existence of an unusable region of gain near the pump frequency which typically corresponds to the region of most optimal phase matching and maximum gain. The inverse Kerr phase matching approach, allows for greater frequency separation between the region of optimal gain and pump, \textit{in situ} tunability of the pump, minimal gain ripple, and a compact footprint which reduces losses. A TWPA employing the inverse Kerr phase matching technique experimentally demonstrated 20 dB of gain over a 3 GHz instantaneous bandwidth, with a tunable bandwidth of 8 GHz, minimal gain ripple, and near quantum-limited noise performance, with 1.5 photons of added noise.
Superconducting travelling-wave parametric amplifiers (TWPAs) provide broadband gain, low added noise, and high dynamic range, making them attractive for applications requiring wide instantaneous bandwidth. This is crucial for amplifying multiplexed narrow band signals spread over a wide frequency range, such as qubit resonator arrays, or amplifying inherently wide band signals, such as in spectrometers or radiometers. In many cases, however, the useful bandwidth of a TWPA is limited by the production of the idler tone at an image frequency. For three-wave-mixing (3WM) TWPAs, for example, an input signal at fs is indistinguishable from one at fp−fs, which can produce spectral ambiguity when the input spectrum is broadband or not known in advance. We experimentally demonstrate a balanced architecture that doubles the instantaneous image-rejected bandwidth available to a 3WM TWPA by spatially separating the amplified signal from the output pump and generated idler, which resolves the sideband degeneracy. The architecture consists of two amplifiers connected between a pair of 180∘ hybrid couplers, with the signal and pump injected and output through the sum and difference ports, respectively. Using two kinetic-inductance TWPAs, we demonstrate approximately 20 dB of signal gain across nearly an octave of bandwidth, together with pump rejection below --20 dB and an average image rejection of approximately --15 dB over the operating band. These results establish balanced TWPAs as a practical approach to broadband parametric amplification, enabling improved contamination free bandwidth and eliminating the need for complex filtering.
Traveling-Wave Parametric Amplifiers (TWPAs) are ubiquitous in superconducting circuit readout, providing high gain with near-quantum-limited noise performance across a wide bandwidth. Their operation, however, relies on a strong microwave pump tone that is typically delivered using off-chip passive components, such as directional couplers or diplexers. These external elements add loss, increase system complexity, and limit scalability. Here, we present a traveling-wave parametric amplifier that incorporates on-chip input and output diplexers for pump routing. This co-fabricated architecture offers a compact and scalable solution for superconducting-circuit readout.
Traveling-wave parametric amplifiers (TWPAs) based on Josephson metamaterials provide broadband gain with near-quantum-limited added noise. Whereas long nonlinear metamaterial devices can deliver high gain, short arrays suffer less from dissipation, pump depletion, and internal standing waves which can degrade noise performance. Here, we demonstrate a cascaded TWPA architecture that combines the advantages of both approaches by employing a short (736-element), low-dissipation Superconducting Nonlinear Asymmetric Inductive eLement (SNAIL)-based TWPA as the first amplification stage, followed by a conventional long (1632-element) TWPA that provides additional gain. The resulting amplifier cascade achieves nearly 30 dB of total gain over a tunable bandwidth of approximately 1 GHz while maintaining added noise close to the quantum limit. Our results establish a cascade of TWPAs as a practical approach for high-gain, broadband, quantum amplification with applications in quantum information processing, multi-mode entanglement, and quantum sensing applications at microwave frequencies.
We investigate the peripheral circuits required to enable ideal performance for a high-gain traveling-wave parametric amplifier (TWPA) based on three-wave mixing . By embedding the TWPA in a network of superconducting diplexers, hybrid couplers, and impedance matching networks, the amplifier can deliver a high stable gain with near-quantum-limited noise performance, with suppressed gain ripples, while eliminating the reflections of the signal, the idler and the pump as well as the transmission of all unwanted tones. We also demonstrate a configuration where the amplifier can isolate. We call this technique (WIF). The theory is supported by simulations that predict over 20 dB gain in the 4–8 GHz band with 10 dB isolation for a single amplifier and 30 dB isolation for two cascaded amplifiers. We demonstrate how the WIF-TWPAs can be used to construct controllable isolators with over 40 dB isolation over the full 4–8 GHz band. Finally, we look at nonidealities and show how certain nonidealities can be devastating for both the gain and the idler filtering, especially a cutoff imbalance or a flux imbalance, and discuss how to compensate for them. Published by the American Physical Society 2024
Kinetic inductance traveling-wave parametric amplifiers (KI-TWPAs) have a wide instantaneous bandwidth with a near quantum-limited noise performance and a relatively high dynamic range. Because of this, they are suitable readout devices for cryogenic detectors and superconducting qubits and have a variety of applications in quantum sensing. This work discusses the design, fabrication, and performance of a KI-TWPA based on four-wave mixing in a NbTiN microstrip transmission line. This device amplifies a signal band from 4 to 8 GHz without contamination from image tones, which are produced in a separate higher frequency band. The 4–8 GHz band is commonly used to read out cryogenic detectors, such as microwave kinetic inductance detectors and Josephson junction-based qubits. We report a measured maximum gain of over 20 dB using four-wave mixing with a 1 dB gain compression point of −58 dBm at 15 dB of gain over that band. The bandwidth and peak gain are tunable by adjusting the pump-tone frequency and power. Using a Y-factor method, we measure an amplifier-added noise of 0.5 ≤ Nadded ≤ 1.5 photons from 4.5 to 8 GHz.