Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2610.23810

Experimental Demonstration of a Balanced Travelling Wave Parametric Amplifier

Nikita Klimovich, Peter K. Day, Henry G. Leduc, Boon-Kok Tan

physics.ins-detcond-mat.supr-conquant-phSubmitted Oct 16, 2026• Announced Oct 19, 2026• 0 citations
arXivHTMLPDF

Abstract

Superconducting travelling-wave parametric amplifiers (TWPAs) provide broadband gain, low added noise, and high dynamic range, making them attractive for applications requiring wide instantaneous bandwidth. This is crucial for amplifying multiplexed narrow band signals spread over a wide frequency range, such as qubit resonator arrays, or amplifying inherently wide band signals, such as in spectrometers or radiometers. In many cases, however, the useful bandwidth of a TWPA is limited by the production of the idler tone at an image frequency. For three-wave-mixing (3WM) TWPAs, for example, an input signal at $f_s$ is indistinguishable from one at $f_p - f_s$, which can produce spectral ambiguity when the input spectrum is broadband or not known in advance. We experimentally demonstrate a balanced architecture that doubles the instantaneous image-rejected bandwidth available to a 3WM TWPA by spatially separating the amplified signal from the output pump and generated idler, which resolves the sideband degeneracy. The architecture consists of two amplifiers connected between a pair of 180$^{\circ}$ hybrid couplers, with the signal and pump injected and output through the sum and difference ports, respectively. Using two kinetic-inductance TWPAs, we demonstrate approximately 20 dB of signal gain across nearly an octave of bandwidth, together with pump rejection below --20 dB and an average image rejection of approximately --15 dB over the operating band. These results establish balanced TWPAs as a practical approach to broadband parametric amplification, enabling improved contamination free bandwidth and eliminating the need for complex filtering.

AI Summary

Conventional three-wave-mixing TWPAs emit the amplified signal, pump, and idler through the same port, creating image ambiguity for broadband or unknown input spectra. This paper experimentally implements a previously proposed balanced architecture that routes the signal and generated idler to different physical outputs, aiming to double the image-free usable bandwidth. Two nominally identical NbTiN kinetic-inductance TWPAs are connected between two $180^\circ$ hybrids. Injecting the signal through the sum port and the pump through the difference port produces in-phase signals but opposite-phase pumps and idlers in the two arms. The output hybrid then separates these components by interference. Frequency-resolved measurements at both outputs, with a $4.75\,\mathrm{GHz}$ pump, show approximately $20\,\mathrm{dB}$ signal gain over the defined $1.8$–$3.2\,\mathrm{GHz}$ operating band, average image leakage near $-15\,\mathrm{dB}$ relative to the desired output, and pump leakage of $-21.37\,\mathrm{dB}$. Individual-device and back-to-back-hybrid measurements characterize gain and imbalance. A multiple-reflection model also explains reduced gain ripple through differential arm phases. Performance is limited by hybrid bandwidth and amplitude/phase imbalance, together with unequal TWPA electrical lengths. The inferred kinetic-inductance mismatch is approximately $0.05\%$; closer wafer placement is proposed to improve matching. At $f_p/2=2.375\,\mathrm{GHz}$, signal and idler coincide spectrally and comparable powers appear at both outputs, giving approximately $0\,\mathrm{dB}$ rejection under the measurement definition. The demonstration does not measure added noise or dynamic range; its experimental performance metrics are gain and pump/image rejection.

Little sign of AI-generated textOverclaims

Error found: The stated 1.8–3.2 GHz operating band includes signals above 3.05 GHz whose idlers fall below the hybrids’ reported 1.7 GHz leakage threshold, qualifying the claimed image-rejected bandwidth. The abstract’s claim that the architecture eliminates complex filtering is broader than the demonstrated finite suppression and the argument that residual pump power is below typical HEMT saturation.

Written by gpt-6.1-sol from the paper's full text. Automated: it can be wrong.

Related papers

Balanced travelling-wave parametric amplifiers for practical applications

Joseph C. Longden, Javier Navarro Montilla, Boon-Kok Tan

Abstract The development of superconducting travelling-wave parametric amplifiers (TWPAs) over the past decade has highlighted their potential as low-noise amplifiers for use in fundamental physics experiments and industrial applications. However, practical challenges, including signal-idler contamination, complex pump injection and cancellation, impedance mismatch, and the reciprocal nature of the device, have made it challenging to deploy TWPAs in real-world applications. In this paper, we introduce an innovative solution to these issues through phase-controlled balanced-TWPA architectures. These architectures involve placing two TWPAs in parallel between a pair of broadband couplers. By carefully controlling the phases of the tones propagating along the TWPAs, we can effectively separate the signal and idler tones, as well as the pump(s), using a straightforward injection and cancellation mechanism. The balanced-TWPA architecture offers versatility and flexibility, as it can be reconfigured either intrinsically or externally to suit different application needs. In this manuscript, we provide a comprehensive discussion of the working principles of the balanced-TWPA, including various configurations designed to meet diverse application requirements. We also present the expected gain-bandwidth products in comparison to traditional TWPAs and conduct tolerance analysis to demonstrate the feasibility and advantages of the balanced-TWPA architecture. By addressing the practical challenges associated with TWPAs, the balanced-TWPA architecture represents a promising advancement in the field, offering a more practical and adaptable solution for a wide range of applications.

Physica Scripta•May 9, 2024•0 citations

A small footprint travelling-wave parametric amplifier with a high Signal-to-Noise Ratio improvement in a wide band

Hampus Renberg Nilsson, Liangyu Chen, Giovanna Tancredi +6 more

We characterise a small footprint travelling-wave parametric amplifier (TWPA). The TWPA is built with magnetically flux-tunable superconducting nonlinear asymmetric inductive elements (SNAILs) and parallel-plate capacitors. It implements three-wave mixing (3WM) with resonant phase matching (RPM), a small cutoff frequency for high gain per unitcell and impedance matching networks for large bandwidth impedance matching. The device has 200 unitcells and a physical footprint of only 1.1 mm^2, yet demonstrates an average parametric gain of 19 dB over a 3 GHz bandwidth, an average effective signal-to-noise ratio improvement of 10 dB and a clear speedup of qubit readout time.

arXiv:2408.16366•Aug 29, 2024•7 citations

Broadband Parametric Amplification in DARTWARS

M. Faverzani, P Campana, Rodolfo Carobene +46 more

Abstract Superconducting parametric amplifiers offer the capability to amplify feeble signals with extremely low levels of added noise, potentially reaching quantum-limited amplification. This characteristic makes them essential components in the realm of high-fidelity quantum computing and serves to propel advancements in the field of quantum sensing. In particular, Traveling-Wave Parametric Amplifiers (TWPAs) may be especially suitable for practical applications due to their multi-Gigahertz amplification bandwidth, a feature lacking in Josephson Parametric Amplifiers (JPAs), despite the latter being a more established technology. This paper presents recent developments of the DARTWARS (Detector Array Readout with Traveling Wave AmplifieRS) project, focusing on the latest prototypes of Kinetic Inductance TWPAs (KITWPAs). The project aims to develop a KITWPA capable of achieving 20 dB of amplification. To enhance the production yield, the first prototypes were fabricated with half the length and expected gain of the final device. In this paper, we present the results of the characterization of one of the half-length prototypes. The measurements revealed an average amplification of approximately 9 dB across a 2 GHz bandwidth for a KITWPA spanning 17 mm in length.

arXiv:2402.12045•Journal of Low Temperature Physics•May 3, 2024•6 citations

Peripheral circuits for ideal performance of a traveling-wave parametric amplifier

Hampus Renberg Nilsson, Daryoush Shiri, Robert Rehammar +2 more

We investigate the peripheral circuits required to enable ideal performance for a high-gain traveling-wave parametric amplifier (TWPA) based on three-wave mixing . By embedding the TWPA in a network of superconducting diplexers, hybrid couplers, and impedance matching networks, the amplifier can deliver a high stable gain with near-quantum-limited noise performance, with suppressed gain ripples, while eliminating the reflections of the signal, the idler and the pump as well as the transmission of all unwanted tones. We also demonstrate a configuration where the amplifier can isolate. We call this technique (WIF). The theory is supported by simulations that predict over 20 dB gain in the 4–8 GHz band with 10 dB isolation for a single amplifier and 30 dB isolation for two cascaded amplifiers. We demonstrate how the WIF-TWPAs can be used to construct controllable isolators with over 40 dB isolation over the full 4–8 GHz band. Finally, we look at nonidealities and show how certain nonidealities can be devastating for both the gain and the idler filtering, especially a cutoff imbalance or a flux imbalance, and discuss how to compensate for them. Published by the American Physical Society 2024

arXiv:2310.11909•Physical Review Applied•Jun 26, 2024•9 citations

A Traveling-Wave Parametric Amplifier With Integrated Diplexers

C. Denney, K. Genter, K. Cicak +4 more

Traveling-Wave Parametric Amplifiers (TWPAs) are ubiquitous in superconducting circuit readout, providing high gain with near-quantum-limited noise performance across a wide bandwidth. Their operation, however, relies on a strong microwave pump tone that is typically delivered using off-chip passive components, such as directional couplers or diplexers. These external elements add loss, increase system complexity, and limit scalability. Here, we present a traveling-wave parametric amplifier that incorporates on-chip input and output diplexers for pump routing. This co-fabricated architecture offers a compact and scalable solution for superconducting-circuit readout.

quant-pharXiv:2603.12327•Mar 16, 2026•1 citation

Low-noise kinetic inductance traveling-wave amplifier using three-wave mixing

Michael R. Vissers, R. P. Erickson, H. S. Ku +4 more

We have fabricated a wide-bandwidth, high dynamic range, low-noise cryogenic amplifier based on a superconducting kinetic inductance traveling-wave device. The device was made from NbTiN and consisted of a long, coplanar waveguide on a silicon chip. By adding a DC current and an RF pump tone we are able to generate parametric amplification using three-wave mixing. The devices exhibit gain of more than 15 dB across an instantaneous bandwidth from 4 to 8 GHz. The total usable gain bandwidth, including both sides of the signal-idler gain region, is more than 6 GHz. The noise referred to the input of the devices approaches the quantum limit, with less than 1 photon excess noise. Compared to similarly constructed four-wave mixing amplifiers, these devices operate with the RF pump at ~20 dB lower power and at frequencies far from the signal. This will permit easier integration into large scale qubit and detector applications.

arXiv:1509.09280•Applied Physics Letters•Jan 4, 2016•137 citations
Superconducting travelling-wave parametric amplifiers (TWPAs) provide broadband gain, low added noise, and high dynamic range, making them attractive for applications requiring wide instantaneous bandwidth. This is crucial for amplifying multiplexed narrow band signals spread over a wide frequency range, such as qubit resonator arrays, or amplifying inherently wide band signals, such as in spectrometers or radiometers. In many cases, however, the useful bandwidth of a TWPA is limited by the production of the idler tone at an image frequency. For three-wave-mixing (3WM) TWPAs, for example, an input signal at fsf_sfs​ is indistinguishable from one at fp−fsf_p - f_sfp​−fs​, which can produce spectral ambiguity when the input spectrum is broadband or not known in advance. We experimentally demonstrate a balanced architecture that doubles the instantaneous image-rejected bandwidth available to a 3WM TWPA by spatially separating the amplified signal from the output pump and generated idler, which resolves the sideband degeneracy. The architecture consists of two amplifiers connected between a pair of 180∘^{\circ}∘ hybrid couplers, with the signal and pump injected and output through the sum and difference ports, respectively. Using two kinetic-inductance TWPAs, we demonstrate approximately 20 dB of signal gain across nearly an octave of bandwidth, together with pump rejection below --20 dB and an average image rejection of approximately --15 dB over the operating band. These results establish balanced TWPAs as a practical approach to broadband parametric amplification, enabling improved contamination free bandwidth and eliminating the need for complex filtering.
Conventional three-wave-mixing TWPAs emit the amplified signal, pump, and idler through the same port, creating image ambiguity for broadband or unknown input spectra. This paper experimentally implements a previously proposed balanced architecture that routes the signal and generated idler to different physical outputs, aiming to double the image-free usable bandwidth.
Two nominally identical NbTiN kinetic-inductance TWPAs are connected between two 180∘180^\circ180∘ hybrids. Injecting the signal through the sum port and the pump through the difference port produces in-phase signals but opposite-phase pumps and idlers in the two arms. The output hybrid then separates these components by interference. Frequency-resolved measurements at both outputs, with a 4.75 GHz4.75\,\mathrm{GHz}4.75GHz pump, show approximately 20 dB20\,\mathrm{dB}20dB signal gain over the defined 1.81.81.8–3.2 GHz3.2\,\mathrm{GHz}3.2GHz operating band, average image leakage near −15 dB-15\,\mathrm{dB}−15dB relative to the desired output, and pump leakage of −21.37 dB-21.37\,\mathrm{dB}−21.37dB. Individual-device and back-to-back-hybrid measurements characterize gain and imbalance. A multiple-reflection model also explains reduced gain ripple through differential arm phases.
Performance is limited by hybrid bandwidth and amplitude/phase imbalance, together with unequal TWPA electrical lengths. The inferred kinetic-inductance mismatch is approximately 0.05%0.05\%0.05%; closer wafer placement is proposed to improve matching. At fp/2=2.375 GHzf_p/2=2.375\,\mathrm{GHz}fp​/2=2.375GHz, signal and idler coincide spectrally and comparable powers appear at both outputs, giving approximately 0 dB0\,\mathrm{dB}0dB rejection under the measurement definition. The demonstration does not measure added noise or dynamic range; its experimental performance metrics are gain and pump/image rejection.
Abstract The development of superconducting travelling-wave parametric amplifiers (TWPAs) over the past decade has highlighted their potential as low-noise amplifiers for use in fundamental physics experiments and industrial applications. However, practical challenges, including signal-idler contamination, complex pump injection and cancellation, impedance mismatch, and the reciprocal nature of the device, have made it challenging to deploy TWPAs in real-world applications. In this paper, we introduce an innovative solution to these issues through phase-controlled balanced-TWPA architectures. These architectures involve placing two TWPAs in parallel between a pair of broadband couplers. By carefully controlling the phases of the tones propagating along the TWPAs, we can effectively separate the signal and idler tones, as well as the pump(s), using a straightforward injection and cancellation mechanism. The balanced-TWPA architecture offers versatility and flexibility, as it can be reconfigured either intrinsically or externally to suit different application needs. In this manuscript, we provide a comprehensive discussion of the working principles of the balanced-TWPA, including various configurations designed to meet diverse application requirements. We also present the expected gain-bandwidth products in comparison to traditional TWPAs and conduct tolerance analysis to demonstrate the feasibility and advantages of the balanced-TWPA architecture. By addressing the practical challenges associated with TWPAs, the balanced-TWPA architecture represents a promising advancement in the field, offering a more practical and adaptable solution for a wide range of applications.
We characterise a small footprint travelling-wave parametric amplifier (TWPA). The TWPA is built with magnetically flux-tunable superconducting nonlinear asymmetric inductive elements (SNAILs) and parallel-plate capacitors. It implements three-wave mixing (3WM) with resonant phase matching (RPM), a small cutoff frequency for high gain per unitcell and impedance matching networks for large bandwidth impedance matching. The device has 200 unitcells and a physical footprint of only 1.1 mm^2, yet demonstrates an average parametric gain of 19 dB over a 3 GHz bandwidth, an average effective signal-to-noise ratio improvement of 10 dB and a clear speedup of qubit readout time.
Abstract Superconducting parametric amplifiers offer the capability to amplify feeble signals with extremely low levels of added noise, potentially reaching quantum-limited amplification. This characteristic makes them essential components in the realm of high-fidelity quantum computing and serves to propel advancements in the field of quantum sensing. In particular, Traveling-Wave Parametric Amplifiers (TWPAs) may be especially suitable for practical applications due to their multi-Gigahertz amplification bandwidth, a feature lacking in Josephson Parametric Amplifiers (JPAs), despite the latter being a more established technology. This paper presents recent developments of the DARTWARS (Detector Array Readout with Traveling Wave AmplifieRS) project, focusing on the latest prototypes of Kinetic Inductance TWPAs (KITWPAs). The project aims to develop a KITWPA capable of achieving 20 dB of amplification. To enhance the production yield, the first prototypes were fabricated with half the length and expected gain of the final device. In this paper, we present the results of the characterization of one of the half-length prototypes. The measurements revealed an average amplification of approximately 9 dB across a 2 GHz bandwidth for a KITWPA spanning 17 mm in length.
We investigate the peripheral circuits required to enable ideal performance for a high-gain traveling-wave parametric amplifier (TWPA) based on three-wave mixing . By embedding the TWPA in a network of superconducting diplexers, hybrid couplers, and impedance matching networks, the amplifier can deliver a high stable gain with near-quantum-limited noise performance, with suppressed gain ripples, while eliminating the reflections of the signal, the idler and the pump as well as the transmission of all unwanted tones. We also demonstrate a configuration where the amplifier can isolate. We call this technique (WIF). The theory is supported by simulations that predict over 20 dB gain in the 4–8 GHz band with 10 dB isolation for a single amplifier and 30 dB isolation for two cascaded amplifiers. We demonstrate how the WIF-TWPAs can be used to construct controllable isolators with over 40 dB isolation over the full 4–8 GHz band. Finally, we look at nonidealities and show how certain nonidealities can be devastating for both the gain and the idler filtering, especially a cutoff imbalance or a flux imbalance, and discuss how to compensate for them. Published by the American Physical Society 2024
Traveling-Wave Parametric Amplifiers (TWPAs) are ubiquitous in superconducting circuit readout, providing high gain with near-quantum-limited noise performance across a wide bandwidth. Their operation, however, relies on a strong microwave pump tone that is typically delivered using off-chip passive components, such as directional couplers or diplexers. These external elements add loss, increase system complexity, and limit scalability. Here, we present a traveling-wave parametric amplifier that incorporates on-chip input and output diplexers for pump routing. This co-fabricated architecture offers a compact and scalable solution for superconducting-circuit readout.
We have fabricated a wide-bandwidth, high dynamic range, low-noise cryogenic amplifier based on a superconducting kinetic inductance traveling-wave device. The device was made from NbTiN and consisted of a long, coplanar waveguide on a silicon chip. By adding a DC current and an RF pump tone we are able to generate parametric amplification using three-wave mixing. The devices exhibit gain of more than 15 dB across an instantaneous bandwidth from 4 to 8 GHz. The total usable gain bandwidth, including both sides of the signal-idler gain region, is more than 6 GHz. The noise referred to the input of the devices approaches the quantum limit, with less than 1 photon excess noise. Compared to similarly constructed four-wave mixing amplifiers, these devices operate with the RF pump at ~20 dB lower power and at frequencies far from the signal. This will permit easier integration into large scale qubit and detector applications.