Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2503.22670 · ACS Photonics

Toward Single-Photon Detection with Superconducting Niobium Diselenide Nanowires

Pietro Metuh, Athanasios Paralikis, Paweł Wyborski, Sherwan Jamo, Alessandro Palermo, Lucio Zugliani, Matteo Barbone, Kai Müller, Niels Gregersen, S. Vaitiekėnas, Jonathan James Finley, Battulga Munkhbat

Published Sep 2, 2025• 7 citations
arXivHTMLPDF

Abstract

High Resolution Image Download MS PowerPoint Slide We present superconducting nanowire photodetectors based on hBN-encapsulated, few-layer NbSe 2, showing signatures of single-photon sensitivity. The top-down fabrication process preserves the superconducting properties of NbSe 2, as confirmed by low-temperature transport measurements showing comparable results to unpatterned sheets, and it maintains a contact and wiring resistance down to ∼30 Ω at T = 4 K. Meandered NbSe 2 nanowires exhibit high responsivity (up to 4.9 × 10 4 V/W) over a spectral range of 650–1550 nm in a closed-cycle cryostat at 4 K, outperforming samples with different geometries in this work. The meander achieves a recovery time of (135 ± 36) ns, a system timing jitter of (1103 ± 7) ps, and a detection efficiency of ∼0.01% at 0.95 I c . A linear increase of the count rate with the number of photons between the noise level and the latching threshold offers a signature of single-photon sensitivity at 1100 nm.

DOI
10.1021/acsphotonics.5c01195

Related papers

Single-photon detection in few-layer NbSe2 superconducting nanowires

Lucio Zugliani, Alessandro Palermo, Bianca Scaparra +11 more

Abstract Superconducting Nanowire Single-Photon Detectors (SNSPDs) are key building blocks for photonic quantum technologies due to their ability to detect single photons with ultra-high efficiency, low dark counts and fast temporal resolution. Superconducting materials exhibiting high uniformity, large absorption cross-section and atomic-scale thickness are desirable to extend single-photon detection from the near-infrared up to the terahertz regime, where existing material choices are especially constrained. Substrate independence would further open the way to integrating detectors onto functional materials and heterostructures, enhancing performance and enabling proximal readout of a wide range of individual excitations. Here, we pattern the prototypical two-dimensional superconductor niobium diselenide (NbSe 2 ) into few-layer nanowires less than 100 nm wide and demonstrate single-photon detection at 780 nm and 1550 nm. At the same time, the dark-count rate remains below 1 Hz up to the switching current and we achieve a timing jitter below 50 ps. We estimate via a diffusive hot-spot model that materials and geometric parameters would allow a theoretical cut-off wavelength in the millimetre range, assuming state-of-the-art device parameters. Our results open up routes toward quantum-limited detectors integrated into quantum-photonic circuits and quantum devices, with the potential for novel detection capabilities and unprecedented energy sensitivity.

arXiv:2508.18843•Nature Communications•Jul 29, 2026•1 citation

Superconducting nanowire single-photon detectors at a wavelength of 940 nm

W. J. Zhang, Hao Li, Lixing You +9 more

We develop single-photon detectors comprising single-mode fiber-coupled superconducting nanowires, with high system detection efficiencies at a wavelength of 940 nm. The detector comprises a 6.5-nm-thick, 110-nm-wide NbN nanowire meander fabricated onto a Si substrate with a distributed Bragg reflector for enhancing the optical absorptance. We demonstrate that, via the design of a low filling factor (1/3) and active area (Φ = 10 μm), the system reaches a detection efficiency of ∼60% with a dark count rate of 10 Hz, a recovery time <12 ns, and a timing jitter of ∼50 ps.

arXiv:1506.07921•AIP Advances•Jun 1, 2015•7 citations

NbN Superconducting Nanowire Single-Photon Detector With 90.5% Saturated System Detection Efficiency and 14.7 ps System Jitter at 1550 nm Wavelength

Xingyu Zhang, Weijun Zhang, Hui Zhou +8 more

Superconducting nanowire single-photon detectors (SNSPDs) play a pivotal role in infrared single-photon-detection applications owing to their free-running mode, near-unity detection efficiency, and excellent time resolution. However, conventional niobium nitride- (NbN) SNSPDs often have a trade-off between optimal detection efficiency and time resolution. We herein demonstrate NbN SNSPDs in the combination of high efficiency and time resolution by using the helium-ion-irradiated film of 10 nm and a homemade cryogenic amplifier to improve the signal-to-noise ratio. The proposed 18-μm-diameter device operated at 850 mK shows a saturated system detection efficiency of ∼90.5% at 1550 nm wavelength with a dark count rate below 50 counts per second (cps), and minimum system timing jitter of ∼14.7 ps. Meanwhile, the recovery time is 21.2 ns owing to its lower kinetic inductance. The time-of-flight light detection and ranging with this device was further carried out indoors, which demonstrates a submillimeter (<0.5 mm) depth resolution, as well as good depth and intensity reconstruction of a low-signature object even under the dwell time of 0.5 ms. It indicates that our device has a great advantage and potential in high-time-resolution and weak-signal-detection applications, such as real-time imaging, fluorescence lifetime detection, and remote laser sensing.

IEEE Journal of Selected Topics in Quantum Electronics•Feb 23, 2022•27 citations

Single-photon and photon-number-resolving detectors based on superconducting nanowires

Francesco Marsili

Nanowire superconducting single photon detectors (SSPDs) [1] are characterized by very high sensitivity in the near infrared (detection efficiency η up to 30%, for a dark count rate DK of few Hz), speed (up to ∼1 GHz repetition rate) and time resolution (jitter of 20 ps full width at half maximum, FWHM). They can be operated at temperatures near 4 K, so they can be packaged in cryogenic dipsticks or cryogen-free refrigerators. These features make SSPDs the most promising detectors for telecom-wavelength single-photon counting applications. The basic structure of an SSPD is a narrow (w=50 to 120 nm), thin (th∼4-10 nm) NbN superconducting nanowire folded in a meander pattern. The typical detector active area (i.e. the size of the pixel) is Ad=10 × 10 µm2 (which allows an efficient coupling with the core of optical fibers at telecom wavelengths) with filling factor (f, the ratio of the area occupied by the superconducting meander to the device total area) ranging from 40% to 60%. The meanders are embedded in a 50 Ω coplanar transmission line. At present, the SSPD detection efficiency is limited by its absorbance (α, the ratio of the number of photons absorbed in the nanowire to the number of incident photons on the device active area). Indeed, it has been shown that in the classic front-illumination configuration α cannot exceed 30%. Our approach to increase α consists in integrating SSPDs with advanced optical structures such as distributed Bragg reflectors (DBRs) and optical waveguides. This requires to transfer the challenging SSPD technology (i.e. the deposition of high-quality few-nm thick NbN films and the nano-patterning by electron beam lithography, EBL) from the usual comfortable substrates, i.e. sapphire and MgO, which are known to allow the deposition of few-nm thick NbN films of excellent quality, to an optical substrate like GaAs, on which DBRs and waveguides can be easily obtained. Our first task was then to optimize a process for the deposition of high-quality few-nm thick NbN films on GaAs and AlAs/GaAs-based DBRs. Because of the requirement of compatibility with GaAs, the substrate temperature used for the depositions is 400°C, in order to prevent As evaporation. As GaAs and DBRs are highly mismatched substrates, the deposition parameters were first optimized with respect to the superconducting properties of NbN films on MgO substrates, which allow the growth of high crystal quality NbN films at low temperature. This made easier to separate the influence of stoichiometry from that of microstructure. The optimized deposition parameters were then used to grow NbN films on GaAs and DBRs, under the reasonable assumption (later checked and confirmed) that changing the substrate would not produce a change in film stoichiometry, but only in its microstructure. NbN films ranging from 150nm to 3nm in thickness were then deposited on epitaxial-quality single crystal MgO, GaAs and DBRs structures. The deposition technique is the current controlled DC magnetron sputtering (planar, circular, balanced configuration) of Nb in an Ar + N2 plasma. NbN films deposited on MgO exhibit superconducting critical temperature ΤC=10 Κ, superconducting transition width ΔΤC=0.8 Κ and residual resistivity ratio RRR=R(20K)/R(300K)=0.8 for th=4 nm, which are state of the art values, proof of the excellent quality of our low-temperature deposition process. The quality of films deposited on GaAs and on DBRs is lower than that of NbN deposited on MgO, as for any thickness they systematically exhibit higher ΔΤC and lower ΤC and RRR. However, 5.5 nm-thick NbN films on GaAs still exhibit ΤC=10.7 Κ, ΔΤC=1.1 Κ and RRR=0.7, which compares with 4.5 nm thick films on MgO, making them suitable for device fabrication. To our knowledge, the growth of such high quality thin NbN films on GaAs and DBRs, has never been reported in literature. The degradation of the superconducting properties exhibited by NbN films on GaAs and DBRs was attributed to a highly defected microstructure, due both to a higher lattice misfit between NbN and GaAs and to a poorer quality of the substrate surface. Encouraging preliminary results show that the quality of these films can be improved either cleaning the GaAs/DBR substrate surface more effectively or adding an MgO buffer layer. SSPDs were fabricated on thin NbN films (th=3-7 nm) deposited under optimal conditions on MgO and GaAs by EBL and reactive ion etching. The geometrical parameters of our detectors are: Ad=5×5 µm2, w=60-200 nm, f=40%-60%. The devices were then characterized both electrically and optically. I-V curves of test structures were measured, from which it was possible to deduce important physical parameters used as figures of merit to estimate the superconducting properties of the nanowires, or for the design and the simulation of the devices. The quality of the devices fabricated on GaAs is poorer than those on MgO, most likely due to the lower quality of NbN films deposited on GaAs and to issues related to the EBL nano-patterning step. Measurements of η and of DK as a function of the bias current were performed on SSPDs fabricated on MgO and GaAs. The best performance was exhibited by a w=100 nm, f=40%, th=4 nm meander, showing η=20% and noise equivalent power NEP=10-16 W/Hz1/2 (at λ=1.3 µm and T=4.2 K), which are state of the art values. This result showed for the first time that high performance NbN SSPDs can be realized on a different substrate and from a deposition process at lower temperature than previously reported. High detection efficiencies could not be measured with SSPDs fabricated on GaAs, but it should be noted that at present only first-generation devices (fabricated on GaAs substrates of poor surface quality) have been tested. Better results are expected from devices fabricated on the improved NbN films grown on clean or MgO-buffered GaAs substrates. Although SSPDs on MgO have shown high detection efficiency, the fabrication yield of high performance detectors has to be improved. Variations of the critical current along a nanowire are responsible for the wide distribution in efficiency values of nominally identical SSPDs. In order to understand the physical origin of the nanowire constrictions (i.e. regions of suppressed superconductivity) we performed a spatially-resolved characterization of η of a long straight nanowire, followed by a high resolution SEM (scanning electron microscope) scan on its whole length. Two types of inhomogeneities were evidenced, corresponding to localized efficiency dips and peaks. The peaks likely correspond to constrictions. SEM observations did not evidence any width narrowing at the position of the efficiency peaks, which suggests that constrictions might be due to thickness or quality inhomogeneities of the film occurring during the film deposition or later in the process. On the other hand, the efficiency dips have been correlated with lithography problems discovered on SEM images. Finally, a new photon number resolving detector, the Parallel Nanowire Detector (PND), has been demonstrated, which significantly outperforms existing approaches in terms of sensitivity, speed and multiplication noise in the telecommunication wavelength range. In particular, it provides a repetition rate (80 MHz) three orders of magnitude larger than any existing detector at telecom wavelength, and a sensitivity (NEP=4.2×10-18 W/Hz1/2) one-two orders of magnitude better, with the exception of transition-edge sensors (which require a much lower operating temperature). An electrical equivalent model of the device was developed in order to study its operation. The modeling predicts a physical limit to the reset time of the PND, which is lower than initially estimated. Furthermore, the figures of merit of the device performance in terms of efficiency, speed and sensitivity were defined and their dependency on the design parameters analyzed. Additionally, we developed modeling tools to fully characterize the device and an algorithm to estimate the photon number statistics of an unknown light using the PND. The reconstruction proved to be successful only for low photon fluxes, most likely due to the limited counting capability and the poor calibration of the detector. The PND, with its high repetition rate and high sensitivity, is then suitable for measuring an unknown photon number probability distribution assuming accurate calibration and sufficient counting capability. ______________________________[1] G. N. Gol'tsman, O. Okunev, G. Chulkova, A. Lipatov, A. Semenov, K. Smirnov, B. Voronov, A. Dzardanov, C. Williams, and R. Sobolewski, Appl. Phys. Lett. 79, 705 (2001).

•Jan 1, 2009•4 citations

Design of NbN superconducting nanowire single photon detectors with enhanced infrared photon detection efficiency

Q. Wang, Jelmer J. Renema, Andreas Engel +1 more

Nanowire superconducting single-photon detectors (SSPDs) consist of a superconducting wire of nanoscale cross-section [1], typically 4×100 nm2. A current close to the device critical current renders the nanowire sensitive to single photons. SSPDs are known for their high efficiency, low jitter, low dark count rate and fast reset time. An important challenge for future application of SSPDs is to extend the useful wavelength range towards the infrared without comprising detector speed or dark count rate. To this end, we explore optical designs with wider nanowires that utilize efficient detection of single photons at the edge of the nanowire. Silicon nanowires on top of a NbN nanowire increase both the calculated total absorption and the internal detection efficiency significantly compared to a standard meandering wire geometry.

arXiv:1612.02840•Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•Jan 1, 2017•1 citation

Performances of NbTiN superconducting nanowire single photon detector

Shigehito Miki, Taro Yamashita, Hirotaka Terai +1 more

We present high performance fiber-coupled niobium titanium nitride superconducting nanowire single photon detectors fabricated on thermally oxidized silicon substrates. By applying a double sided cavity structure, simulated absorptance in the nanowire meander reached 97% at 1550 nm wavelength. The fabricated device showed a system detection efficiency (DE) of 74% at 1550 nm, dark count rate of 100 c/s, and a full width at half maximum timing jitter of 68 ps under a bias current of 18.0 μA with a practical Gifford-McMahon cryocooler system.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2013•1 citation
High Resolution Image Download MS PowerPoint Slide We present superconducting nanowire photodetectors based on hBN-encapsulated, few-layer NbSe 2, showing signatures of single-photon sensitivity. The top-down fabrication process preserves the superconducting properties of NbSe 2, as confirmed by low-temperature transport measurements showing comparable results to unpatterned sheets, and it maintains a contact and wiring resistance down to ∼30 Ω at T = 4 K. Meandered NbSe 2 nanowires exhibit high responsivity (up to 4.9 × 10 4 V/W) over a spectral range of 650–1550 nm in a closed-cycle cryostat at 4 K, outperforming samples with different geometries in this work. The meander achieves a recovery time of (135 ± 36) ns, a system timing jitter of (1103 ± 7) ps, and a detection efficiency of ∼0.01% at 0.95 I c . A linear increase of the count rate with the number of photons between the noise level and the latching threshold offers a signature of single-photon sensitivity at 1100 nm.
Abstract Superconducting Nanowire Single-Photon Detectors (SNSPDs) are key building blocks for photonic quantum technologies due to their ability to detect single photons with ultra-high efficiency, low dark counts and fast temporal resolution. Superconducting materials exhibiting high uniformity, large absorption cross-section and atomic-scale thickness are desirable to extend single-photon detection from the near-infrared up to the terahertz regime, where existing material choices are especially constrained. Substrate independence would further open the way to integrating detectors onto functional materials and heterostructures, enhancing performance and enabling proximal readout of a wide range of individual excitations. Here, we pattern the prototypical two-dimensional superconductor niobium diselenide (NbSe 2 ) into few-layer nanowires less than 100 nm wide and demonstrate single-photon detection at 780 nm and 1550 nm. At the same time, the dark-count rate remains below 1 Hz up to the switching current and we achieve a timing jitter below 50 ps. We estimate via a diffusive hot-spot model that materials and geometric parameters would allow a theoretical cut-off wavelength in the millimetre range, assuming state-of-the-art device parameters. Our results open up routes toward quantum-limited detectors integrated into quantum-photonic circuits and quantum devices, with the potential for novel detection capabilities and unprecedented energy sensitivity.
We develop single-photon detectors comprising single-mode fiber-coupled superconducting nanowires, with high system detection efficiencies at a wavelength of 940 nm. The detector comprises a 6.5-nm-thick, 110-nm-wide NbN nanowire meander fabricated onto a Si substrate with a distributed Bragg reflector for enhancing the optical absorptance. We demonstrate that, via the design of a low filling factor (1/3) and active area (Φ = 10 μm), the system reaches a detection efficiency of ∼60% with a dark count rate of 10 Hz, a recovery time <12 ns, and a timing jitter of ∼50 ps.
Superconducting nanowire single-photon detectors (SNSPDs) play a pivotal role in infrared single-photon-detection applications owing to their free-running mode, near-unity detection efficiency, and excellent time resolution. However, conventional niobium nitride- (NbN) SNSPDs often have a trade-off between optimal detection efficiency and time resolution. We herein demonstrate NbN SNSPDs in the combination of high efficiency and time resolution by using the helium-ion-irradiated film of 10 nm and a homemade cryogenic amplifier to improve the signal-to-noise ratio. The proposed 18-μm-diameter device operated at 850 mK shows a saturated system detection efficiency of ∼90.5% at 1550 nm wavelength with a dark count rate below 50 counts per second (cps), and minimum system timing jitter of ∼14.7 ps. Meanwhile, the recovery time is 21.2 ns owing to its lower kinetic inductance. The time-of-flight light detection and ranging with this device was further carried out indoors, which demonstrates a submillimeter (<0.5 mm) depth resolution, as well as good depth and intensity reconstruction of a low-signature object even under the dwell time of 0.5 ms. It indicates that our device has a great advantage and potential in high-time-resolution and weak-signal-detection applications, such as real-time imaging, fluorescence lifetime detection, and remote laser sensing.
Nanowire superconducting single photon detectors (SSPDs) [1] are characterized by very high sensitivity in the near infrared (detection efficiency η up to 30%, for a dark count rate DK of few Hz), speed (up to ∼1 GHz repetition rate) and time resolution (jitter of 20 ps full width at half maximum, FWHM). They can be operated at temperatures near 4 K, so they can be packaged in cryogenic dipsticks or cryogen-free refrigerators. These features make SSPDs the most promising detectors for telecom-wavelength single-photon counting applications. The basic structure of an SSPD is a narrow (w=50 to 120 nm), thin (th∼4-10 nm) NbN superconducting nanowire folded in a meander pattern. The typical detector active area (i.e. the size of the pixel) is Ad=10 × 10 µm2 (which allows an efficient coupling with the core of optical fibers at telecom wavelengths) with filling factor (f, the ratio of the area occupied by the superconducting meander to the device total area) ranging from 40% to 60%. The meanders are embedded in a 50 Ω coplanar transmission line. At present, the SSPD detection efficiency is limited by its absorbance (α, the ratio of the number of photons absorbed in the nanowire to the number of incident photons on the device active area). Indeed, it has been shown that in the classic front-illumination configuration α cannot exceed 30%. Our approach to increase α consists in integrating SSPDs with advanced optical structures such as distributed Bragg reflectors (DBRs) and optical waveguides. This requires to transfer the challenging SSPD technology (i.e. the deposition of high-quality few-nm thick NbN films and the nano-patterning by electron beam lithography, EBL) from the usual comfortable substrates, i.e. sapphire and MgO, which are known to allow the deposition of few-nm thick NbN films of excellent quality, to an optical substrate like GaAs, on which DBRs and waveguides can be easily obtained. Our first task was then to optimize a process for the deposition of high-quality few-nm thick NbN films on GaAs and AlAs/GaAs-based DBRs. Because of the requirement of compatibility with GaAs, the substrate temperature used for the depositions is 400°C, in order to prevent As evaporation. As GaAs and DBRs are highly mismatched substrates, the deposition parameters were first optimized with respect to the superconducting properties of NbN films on MgO substrates, which allow the growth of high crystal quality NbN films at low temperature. This made easier to separate the influence of stoichiometry from that of microstructure. The optimized deposition parameters were then used to grow NbN films on GaAs and DBRs, under the reasonable assumption (later checked and confirmed) that changing the substrate would not produce a change in film stoichiometry, but only in its microstructure. NbN films ranging from 150nm to 3nm in thickness were then deposited on epitaxial-quality single crystal MgO, GaAs and DBRs structures. The deposition technique is the current controlled DC magnetron sputtering (planar, circular, balanced configuration) of Nb in an Ar + N2 plasma. NbN films deposited on MgO exhibit superconducting critical temperature ΤC=10 Κ, superconducting transition width ΔΤC=0.8 Κ and residual resistivity ratio RRR=R(20K)/R(300K)=0.8 for th=4 nm, which are state of the art values, proof of the excellent quality of our low-temperature deposition process. The quality of films deposited on GaAs and on DBRs is lower than that of NbN deposited on MgO, as for any thickness they systematically exhibit higher ΔΤC and lower ΤC and RRR. However, 5.5 nm-thick NbN films on GaAs still exhibit ΤC=10.7 Κ, ΔΤC=1.1 Κ and RRR=0.7, which compares with 4.5 nm thick films on MgO, making them suitable for device fabrication. To our knowledge, the growth of such high quality thin NbN films on GaAs and DBRs, has never been reported in literature. The degradation of the superconducting properties exhibited by NbN films on GaAs and DBRs was attributed to a highly defected microstructure, due both to a higher lattice misfit between NbN and GaAs and to a poorer quality of the substrate surface. Encouraging preliminary results show that the quality of these films can be improved either cleaning the GaAs/DBR substrate surface more effectively or adding an MgO buffer layer. SSPDs were fabricated on thin NbN films (th=3-7 nm) deposited under optimal conditions on MgO and GaAs by EBL and reactive ion etching. The geometrical parameters of our detectors are: Ad=5×5 µm2, w=60-200 nm, f=40%-60%. The devices were then characterized both electrically and optically. I-V curves of test structures were measured, from which it was possible to deduce important physical parameters used as figures of merit to estimate the superconducting properties of the nanowires, or for the design and the simulation of the devices. The quality of the devices fabricated on GaAs is poorer than those on MgO, most likely due to the lower quality of NbN films deposited on GaAs and to issues related to the EBL nano-patterning step. Measurements of η and of DK as a function of the bias current were performed on SSPDs fabricated on MgO and GaAs. The best performance was exhibited by a w=100 nm, f=40%, th=4 nm meander, showing η=20% and noise equivalent power NEP=10-16 W/Hz1/2 (at λ=1.3 µm and T=4.2 K), which are state of the art values. This result showed for the first time that high performance NbN SSPDs can be realized on a different substrate and from a deposition process at lower temperature than previously reported. High detection efficiencies could not be measured with SSPDs fabricated on GaAs, but it should be noted that at present only first-generation devices (fabricated on GaAs substrates of poor surface quality) have been tested. Better results are expected from devices fabricated on the improved NbN films grown on clean or MgO-buffered GaAs substrates. Although SSPDs on MgO have shown high detection efficiency, the fabrication yield of high performance detectors has to be improved. Variations of the critical current along a nanowire are responsible for the wide distribution in efficiency values of nominally identical SSPDs. In order to understand the physical origin of the nanowire constrictions (i.e. regions of suppressed superconductivity) we performed a spatially-resolved characterization of η of a long straight nanowire, followed by a high resolution SEM (scanning electron microscope) scan on its whole length. Two types of inhomogeneities were evidenced, corresponding to localized efficiency dips and peaks. The peaks likely correspond to constrictions. SEM observations did not evidence any width narrowing at the position of the efficiency peaks, which suggests that constrictions might be due to thickness or quality inhomogeneities of the film occurring during the film deposition or later in the process. On the other hand, the efficiency dips have been correlated with lithography problems discovered on SEM images. Finally, a new photon number resolving detector, the Parallel Nanowire Detector (PND), has been demonstrated, which significantly outperforms existing approaches in terms of sensitivity, speed and multiplication noise in the telecommunication wavelength range. In particular, it provides a repetition rate (80 MHz) three orders of magnitude larger than any existing detector at telecom wavelength, and a sensitivity (NEP=4.2×10-18 W/Hz1/2) one-two orders of magnitude better, with the exception of transition-edge sensors (which require a much lower operating temperature). An electrical equivalent model of the device was developed in order to study its operation. The modeling predicts a physical limit to the reset time of the PND, which is lower than initially estimated. Furthermore, the figures of merit of the device performance in terms of efficiency, speed and sensitivity were defined and their dependency on the design parameters analyzed. Additionally, we developed modeling tools to fully characterize the device and an algorithm to estimate the photon number statistics of an unknown light using the PND. The reconstruction proved to be successful only for low photon fluxes, most likely due to the limited counting capability and the poor calibration of the detector. The PND, with its high repetition rate and high sensitivity, is then suitable for measuring an unknown photon number probability distribution assuming accurate calibration and sufficient counting capability. ______________________________[1] G. N. Gol'tsman, O. Okunev, G. Chulkova, A. Lipatov, A. Semenov, K. Smirnov, B. Voronov, A. Dzardanov, C. Williams, and R. Sobolewski, Appl. Phys. Lett. 79, 705 (2001).
Nanowire superconducting single-photon detectors (SSPDs) consist of a superconducting wire of nanoscale cross-section [1], typically 4×100 nm2. A current close to the device critical current renders the nanowire sensitive to single photons. SSPDs are known for their high efficiency, low jitter, low dark count rate and fast reset time. An important challenge for future application of SSPDs is to extend the useful wavelength range towards the infrared without comprising detector speed or dark count rate. To this end, we explore optical designs with wider nanowires that utilize efficient detection of single photons at the edge of the nanowire. Silicon nanowires on top of a NbN nanowire increase both the calculated total absorption and the internal detection efficiency significantly compared to a standard meandering wire geometry.
We present high performance fiber-coupled niobium titanium nitride superconducting nanowire single photon detectors fabricated on thermally oxidized silicon substrates. By applying a double sided cavity structure, simulated absorptance in the nanowire meander reached 97% at 1550 nm wavelength. The fabricated device showed a system detection efficiency (DE) of 74% at 1550 nm, dark count rate of 100 c/s, and a full width at half maximum timing jitter of 68 ps under a bias current of 18.0 μA with a practical Gifford-McMahon cryocooler system.