Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1612.02840 · Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)

Design of NbN superconducting nanowire single photon detectors with enhanced infrared photon detection efficiency

Q. Wang, Jelmer J. Renema, Andreas Engel, M. J. A. de Dood

Published Jan 1, 2017• 1 citation
arXivHTMLPDF

Abstract

Nanowire superconducting single-photon detectors (SSPDs) consist of a superconducting wire of nanoscale cross-section [1], typically 4×100 nm2. A current close to the device critical current renders the nanowire sensitive to single photons. SSPDs are known for their high efficiency, low jitter, low dark count rate and fast reset time. An important challenge for future application of SSPDs is to extend the useful wavelength range towards the infrared without comprising detector speed or dark count rate. To this end, we explore optical designs with wider nanowires that utilize efficient detection of single photons at the edge of the nanowire. Silicon nanowires on top of a NbN nanowire increase both the calculated total absorption and the internal detection efficiency significantly compared to a standard meandering wire geometry.

DOI
10.1109/cleoe-eqec.2017.8087128

Related papers

Design of efficient superconducting nanowire single photon detectors for near-infrared wavelengths

M. J. A. de Dood

Superconducting single photon detectors consist of a narrow and thin wire of superconductor and can detect single photons with high efficiency and high speed. Simultaneous optimization of the detection efficiency and detector response time is difficult because the response time is set by the dimensions of the wire (cross section and length) while the detection efficiency is determined by both the internal detection mechanism and the dimensions of the wire. Wider and shorter wires are easier to fabricate, are more robust and lead to shorter detector reset time, but are generally less efficient. Experiments employing detector tomography provide important insights into the photon detection mechanism and indicate a detection mechanism where the edges of the wire are more efficient. This leads to a position dependent local detection efficiency that can be explained in the context of a photon-assisted-vortex-entry model and predicts an optimum wire width ~70 nm. A 50 nm wide silicon nanowire deposited on top of a 150 nm wide NbN nanowire directs light at 1550 nm wavelength to the edges and improves both the total absorption efficiency and the internal detection efficiency of the wire. The total absorption efficiency can be enhanced by 30% while the internal detection efficiency is increased by 70%. Assuming that the wire covers a similar area the detector response time is reduced 4-fold compared to the standard design using a 70 nm wide wire.

Advanced Photon Counting Techniques•May 14, 2018•0 citations

Superconducting single photon detectors for ultrasensitive visible and IR detection

R. Espiau de Lamaëstre, L. Maingault, Laurent Frey +5 more

Superconducting single photons detectors (SSPDs) have emerged in recent years as a promising alternative for fast and sensitive infrared detectors working in the photon counting mode. In particular, those detectors combine very low dark count rates (below 1 Hz), high speed (above 1GHz), photon number resolution and reasonable quantum efficiency (10 % at telecom wavelengths). They already found applications in quantum cryptography systems and integrated circuit failure analysis, but could also be used as ultimate sensors in matrix configurations. We show here the optimization of SSPD fabrication and their optical metrology at CEA. SSPD are fabricated by patterning a 80 nm wide nanowire in a very thin (4 nm) NbN film on sapphire, forming a pixel of several microns size. A cryogenic all-fibered optoelectronic system has been developed and allows precise metrology of the optical performances of SSPD. When biasing near the critical current of the nanowire, we demonstrate a detection quantum efficiency of 8 % at 1.55 μm, which is also found to be strongly polarization dependent. This quantum efficiency being limited by optical absorption, we propose a prism coupling based absorption enhancing structure that allows reaching 100 % quantum efficiency.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jan 22, 2009•4 citations

Next generation superconducting nanowire single-photon detectors

Kleanthis Erotokritou

Single photon detection advanced rapidly in the last decade. The superconducting nanowire single-photon detector (SNSPD) is an emerging technology, which offers low dark count rates, broadband sensitivity from visible to mid-infrared wavelengths and very high quantum efficiency. All these features are appealing for future emerging applications in remote gas sensing, quantum key distribution and quantum information processing. By enclosing the detector in an optical cavity, tuned to the operating wavelength, the total system detection of the SNSPD is improved. Based on the cavity design, the detector absorption is boosted at the desired experimental wavelength. Devices have been fabricated and tested, in this thesis, with enhanced detection efficiency at near-infrared, infrared and mid-infrared wavelengths. NbTiN detectors fabricated on Ta2O5 / SiO2 distributed Bragg reflectors (DBR) for front-side coupling exhibit a system detection efficiency of ≈ 90% at λ = 940 nm for the best device measured. SNSPDs were also fabricated in NbTiN on metallic mirrors for back-side coupling for 1550 and 2333 nm experimental wavelengths. The first design exhibited a system detection efficiency of ≈ 84.5%, at λ = 1550 nm for the best device measured. The second exhibited low system detection efficiency since the device suffered from unexpectedly high dark count rate mainly due to blackbody radiation at 2.2 K. However, it was possible to measure the timing jitter of this device at 350 mK indicating a FWHM of 84 ps. Another technique to improve the total system detection efficiency of the SNSPD, is by fabricating a hairpin-shaped nanowire atop a single mode waveguide. In this design, photons travel through the waveguide and via evanescent coupling are absorbed in the nanowire. These SNSPD devices have been designed to thread along single mode Si ridge waveguides using a hairpin-shaped nanowire structure, which offers enhanced coupling and absorption efficiency via evanescent coupling. These ultra-thin superconducting MoSi detectors are precisely patterned on top of a single mode Si waveguide (600 nm) with alignment error less than 40 nm. Low temperature electrical and nano-optical characterization was carried out using a two-stage pulse tube (PT) coldhead, using an additional 4He / 3He sorption pump, low vibration characterization of SNSPD devices at 350 mK was carried out. Characterised devices exhibit low dark count rate <5 counts per second and timing jitter of ≈ 83 ps full width half maximum (FWHM) at wavelength (λ) = 1550 nm and at critical current ≈ 30 µA.

•Jan 1, 2019•0 citations

Recent advances in superconducting NbN single-photon detector development

Alexander A. Korneev, Alexander V. Divochiy, Yu. B. Vachtomin +14 more

Superconducting single-photon detector (SSPD) is a planar nanostructure patterned from 4-nm-thick NbN film deposited on sapphire substrate. The sensitive element of the SSPD is 100-nm-wide NbN strip. The device is operated at liquid helium temperature. Absorption of a photon leads to a local suppression of superconductivity producing subnanosecond-long voltage pulse. In infrared (at 1550 nm and longer wavelengths) SSPD outperforms avalanche photodiodes in terms of detection efficiency (DE), dark counts rate, maximum counting rate and timing jitter. Efficient single-mode fibre coupling of the SSPD enabled its usage in many applications ranging from single-photon sources research to quantum cryptography. Recently we managed to improve the SSPD performance and measured 25% detection efficiency at 1550 nm wavelength and dark counts rate of 10 s-1. We also improved photon-number resolving SSPD (PNR-SSPD) which realizes a spatial multiplexing of incident photons enabling resolving of up to 4 simultaneously absorbed photons. Another improvement is the increase of the photon absorption using a λ/4 microcavity integrated with the SSPD. And finally in our strive to increase the DE at longer wavelengths we fabricated SSPD with the strip almost twice narrower compared to the standard 100 nm and demonstrated that in middle infrared (about 3 μm wavelength) these devices have DE several times higher compared to the traditional SSPDs.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Apr 30, 2011•4 citations

Superconducting nanowire single-photon detectors at a wavelength of 940 nm

W. J. Zhang, Hao Li, Lixing You +9 more

We develop single-photon detectors comprising single-mode fiber-coupled superconducting nanowires, with high system detection efficiencies at a wavelength of 940 nm. The detector comprises a 6.5-nm-thick, 110-nm-wide NbN nanowire meander fabricated onto a Si substrate with a distributed Bragg reflector for enhancing the optical absorptance. We demonstrate that, via the design of a low filling factor (1/3) and active area (Φ = 10 μm), the system reaches a detection efficiency of ∼60% with a dark count rate of 10 Hz, a recovery time <12 ns, and a timing jitter of ∼50 ps.

arXiv:1506.07921•AIP Advances•Jun 1, 2015•7 citations

New Generation of Nanowire NbN Superconducting Single-Photon Detector for Mid-Infrared

Yu. P. Korneeva, Irina Florya, Alexander V. Semenov +2 more

We present a break-through approach to mid-infrared single-photon detection based on nanowire NbN superconducting single-photon detectors (SSPD). Although SSPD became a mature technology for telecom wavelengths (1.3-1.55 μm) its further expansion to mid-infrared wavelength was hampered by low sensitivity above 2 μm. We managed to overcome this limit by reducing the nanowire width to 50 nm, while retaining high superconducting properties and connecting the wires in parallel to produce a voltage response of sufficient magnitude. The new device exhibits 10 times better quantum efficiency at 3.5 μm wavelength than the “standard” SSPD.

IEEE Transactions on Applied Superconductivity•Nov 18, 2010•27 citations
Nanowire superconducting single-photon detectors (SSPDs) consist of a superconducting wire of nanoscale cross-section [1], typically 4×100 nm2. A current close to the device critical current renders the nanowire sensitive to single photons. SSPDs are known for their high efficiency, low jitter, low dark count rate and fast reset time. An important challenge for future application of SSPDs is to extend the useful wavelength range towards the infrared without comprising detector speed or dark count rate. To this end, we explore optical designs with wider nanowires that utilize efficient detection of single photons at the edge of the nanowire. Silicon nanowires on top of a NbN nanowire increase both the calculated total absorption and the internal detection efficiency significantly compared to a standard meandering wire geometry.
Superconducting single photon detectors consist of a narrow and thin wire of superconductor and can detect single photons with high efficiency and high speed. Simultaneous optimization of the detection efficiency and detector response time is difficult because the response time is set by the dimensions of the wire (cross section and length) while the detection efficiency is determined by both the internal detection mechanism and the dimensions of the wire. Wider and shorter wires are easier to fabricate, are more robust and lead to shorter detector reset time, but are generally less efficient. Experiments employing detector tomography provide important insights into the photon detection mechanism and indicate a detection mechanism where the edges of the wire are more efficient. This leads to a position dependent local detection efficiency that can be explained in the context of a photon-assisted-vortex-entry model and predicts an optimum wire width ~70 nm. A 50 nm wide silicon nanowire deposited on top of a 150 nm wide NbN nanowire directs light at 1550 nm wavelength to the edges and improves both the total absorption efficiency and the internal detection efficiency of the wire. The total absorption efficiency can be enhanced by 30% while the internal detection efficiency is increased by 70%. Assuming that the wire covers a similar area the detector response time is reduced 4-fold compared to the standard design using a 70 nm wide wire.
Superconducting single photons detectors (SSPDs) have emerged in recent years as a promising alternative for fast and sensitive infrared detectors working in the photon counting mode. In particular, those detectors combine very low dark count rates (below 1 Hz), high speed (above 1GHz), photon number resolution and reasonable quantum efficiency (10 % at telecom wavelengths). They already found applications in quantum cryptography systems and integrated circuit failure analysis, but could also be used as ultimate sensors in matrix configurations. We show here the optimization of SSPD fabrication and their optical metrology at CEA. SSPD are fabricated by patterning a 80 nm wide nanowire in a very thin (4 nm) NbN film on sapphire, forming a pixel of several microns size. A cryogenic all-fibered optoelectronic system has been developed and allows precise metrology of the optical performances of SSPD. When biasing near the critical current of the nanowire, we demonstrate a detection quantum efficiency of 8 % at 1.55 μm, which is also found to be strongly polarization dependent. This quantum efficiency being limited by optical absorption, we propose a prism coupling based absorption enhancing structure that allows reaching 100 % quantum efficiency.
Single photon detection advanced rapidly in the last decade. The superconducting nanowire single-photon detector (SNSPD) is an emerging technology, which offers low dark count rates, broadband sensitivity from visible to mid-infrared wavelengths and very high quantum efficiency. All these features are appealing for future emerging applications in remote gas sensing, quantum key distribution and quantum information processing. By enclosing the detector in an optical cavity, tuned to the operating wavelength, the total system detection of the SNSPD is improved. Based on the cavity design, the detector absorption is boosted at the desired experimental wavelength. Devices have been fabricated and tested, in this thesis, with enhanced detection efficiency at near-infrared, infrared and mid-infrared wavelengths. NbTiN detectors fabricated on Ta2O5 / SiO2 distributed Bragg reflectors (DBR) for front-side coupling exhibit a system detection efficiency of ≈ 90% at λ = 940 nm for the best device measured. SNSPDs were also fabricated in NbTiN on metallic mirrors for back-side coupling for 1550 and 2333 nm experimental wavelengths. The first design exhibited a system detection efficiency of ≈ 84.5%, at λ = 1550 nm for the best device measured. The second exhibited low system detection efficiency since the device suffered from unexpectedly high dark count rate mainly due to blackbody radiation at 2.2 K. However, it was possible to measure the timing jitter of this device at 350 mK indicating a FWHM of 84 ps. Another technique to improve the total system detection efficiency of the SNSPD, is by fabricating a hairpin-shaped nanowire atop a single mode waveguide. In this design, photons travel through the waveguide and via evanescent coupling are absorbed in the nanowire. These SNSPD devices have been designed to thread along single mode Si ridge waveguides using a hairpin-shaped nanowire structure, which offers enhanced coupling and absorption efficiency via evanescent coupling. These ultra-thin superconducting MoSi detectors are precisely patterned on top of a single mode Si waveguide (600 nm) with alignment error less than 40 nm. Low temperature electrical and nano-optical characterization was carried out using a two-stage pulse tube (PT) coldhead, using an additional 4He / 3He sorption pump, low vibration characterization of SNSPD devices at 350 mK was carried out. Characterised devices exhibit low dark count rate <5 counts per second and timing jitter of ≈ 83 ps full width half maximum (FWHM) at wavelength (λ) = 1550 nm and at critical current ≈ 30 µA.
Superconducting single-photon detector (SSPD) is a planar nanostructure patterned from 4-nm-thick NbN film deposited on sapphire substrate. The sensitive element of the SSPD is 100-nm-wide NbN strip. The device is operated at liquid helium temperature. Absorption of a photon leads to a local suppression of superconductivity producing subnanosecond-long voltage pulse. In infrared (at 1550 nm and longer wavelengths) SSPD outperforms avalanche photodiodes in terms of detection efficiency (DE), dark counts rate, maximum counting rate and timing jitter. Efficient single-mode fibre coupling of the SSPD enabled its usage in many applications ranging from single-photon sources research to quantum cryptography. Recently we managed to improve the SSPD performance and measured 25% detection efficiency at 1550 nm wavelength and dark counts rate of 10 s-1. We also improved photon-number resolving SSPD (PNR-SSPD) which realizes a spatial multiplexing of incident photons enabling resolving of up to 4 simultaneously absorbed photons. Another improvement is the increase of the photon absorption using a λ/4 microcavity integrated with the SSPD. And finally in our strive to increase the DE at longer wavelengths we fabricated SSPD with the strip almost twice narrower compared to the standard 100 nm and demonstrated that in middle infrared (about 3 μm wavelength) these devices have DE several times higher compared to the traditional SSPDs.
We develop single-photon detectors comprising single-mode fiber-coupled superconducting nanowires, with high system detection efficiencies at a wavelength of 940 nm. The detector comprises a 6.5-nm-thick, 110-nm-wide NbN nanowire meander fabricated onto a Si substrate with a distributed Bragg reflector for enhancing the optical absorptance. We demonstrate that, via the design of a low filling factor (1/3) and active area (Φ = 10 μm), the system reaches a detection efficiency of ∼60% with a dark count rate of 10 Hz, a recovery time <12 ns, and a timing jitter of ∼50 ps.
We present a break-through approach to mid-infrared single-photon detection based on nanowire NbN superconducting single-photon detectors (SSPD). Although SSPD became a mature technology for telecom wavelengths (1.3-1.55 μm) its further expansion to mid-infrared wavelength was hampered by low sensitivity above 2 μm. We managed to overcome this limit by reducing the nanowire width to 50 nm, while retaining high superconducting properties and connecting the wires in parallel to produce a voltage response of sufficient magnitude. The new device exhibits 10 times better quantum efficiency at 3.5 μm wavelength than the “standard” SSPD.