Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2306.10212 · Physical Review Applied

Active initialization experiment of a superconducting qubit using a quantum circuit refrigerator

Teruaki Yoshioka, Hiroto Mukai, Akiyoshi Tomonaga, Shintaro Takada, Yuma Okazaki, Nobu‐Hisa Kaneko, Shuji Nakamura, Jaw-Shen Tsai

Published Oct 30, 2023• 27 citations
arXivHTMLPDF

Abstract

The initialization of superconducting qubits is one of the essential techniques for the realization of quantum computation. In previous research, initialization above 99% fidelity has been achieved at 280 ns. Here, we demonstrate the rapid initialization of a superconducting qubit with a quantum circuit refrigerator (QCR). Photon-assisted tunneling of quasiparticles in the QCR can temporally increase the relaxation time of photons inside the resonator and helps release energy from the qubit to the environment. Experiments using this protocol have shown that 99% of initialization time is reduced to 200 ns. This initialization time depends strongly on the relaxation rate of the resonator, and faster initialization is possible by reducing the resistance of the QCR, which limits the on:off ratio, and by strengthening the coupling between the QCR and the resonator.

DOI
10.1103/physrevapplied.20.044077

Related papers

Initial experimental results on a superconducting-qubit reset based on photon-assisted quasiparticle tunneling

Vasilii Sevriuk, Wei Liu, Jami Rönkkö +15 more

We present here our recent results on qubit reset scheme based on a quantum-circuit refrigerator (QCR). In particular, we use the photon-assisted quasiparticle tunneling through a superconductor–insulator–normal-metal–insulator–superconductor junction to controllably decrease the energy relaxation time of the qubit during the QCR operation. In our experiment, we use a transmon qubit with dispersive readout. The QCR is capacitively coupled to the qubit through its normal-metal island. We employ rapid, square-shaped QCR control voltage pulses with durations in the range of 2–350 ns and a variety of amplitudes to optimize the reset time and fidelity. Consequently, we reach a qubit ground-state probability of roughly 97% with 80-ns pulses starting from the first excited state. The qubit state probability is extracted from averaged readout signal, where the calibration is based on Rabi oscillations, thus not distinguishing the residual thermal population of the qubit.

arXiv:2212.01065•Applied Physics Letters•Dec 5, 2022•17 citations

Fast unconditional initialization for superconducting qubit and resonator using quantum-circuit refrigerator

T. Yoshioka, J. S. Tsai

In a quantum computation scheme, such as recycling a qubit, the initialization of the qubit is always required. At present, the initialization of the qubit is one of the bottlenecks in such computation, and high fidelity and fast initialization still remain important research subjects. In this study, by coupling a SINIS (superconductor–insulator–normal metal–insulator–superconductor) junction to a coupled system consisting of a qubit and a resonator, a photon is removed from the resonator by single-photon-assisted tunneling, and the effective relaxation rate of the resonator is increased. In addition, by applying an |e,0⟩−|f,0⟩ drive pulse and an |f,0⟩−|g,1⟩ drive pulse to the qubit, the energy of the qubit is rapidly transferred to the resonator to realize high-speed initialization. The present simulation shows that the qubit can be initialized with 99% fidelity in 80 ns and 99.9% in 137 ns when the electron temperature of the normal metal of the SINIS junction is 10 mK. The simulation also shows that the relaxation time of the qubit is about 13% longer when the resonator is interposed between the SINIS junction and the qubit than when the SINIS junction is directly coupled to the qubit.

Applied Physics Letters•Sep 20, 2021•15 citations

Single-junction quantum-circuit refrigerator

Vasilii Vadimov, A. Viitanen, Timm Mörstedt +2 more

We propose a quantum-circuit refrigerator (QCR) based on photon-assisted quasiparticle tunneling through a single normal-metal–insulator–superconductor (NIS) junction. In contrast to previous studies with multiple junctions and an additional charge island for the QCR, we directly connect the NIS junction to an inductively shunted electrode of a superconducting microwave resonator making the device immune to low-frequency charge noise. At low characteristic impedance of the resonator and parameters relevant to a recent experiment, we observe that a semiclassical impedance model of the NIS junction reproduces the bias voltage dependence of the QCR-induced damping rate and frequency shift. For high characteristic impedances, we derive a Born–Markov master equation and use it to observe significant non-linearities in the QCR-induced dissipation and frequency shift. We further demonstrate that, in this regime, the QCR can be used to initialize the linear resonator into a non-thermal state even in the absence of any microwave drive.

arXiv:2112.08008•AIP Advances•Jul 1, 2022•17 citations

Quantum-circuit refrigeration of a superconducting microwave resonator well below a single quantum

Arto Viitanen, Timm Mörstedt, Wallace S. Teixeira +4 more

We experimentally demonstrate a recently proposed single-junction quantum-circuit refrigerator (QCR) as an tunable low-temperature environment for a superconducting 4.7 GHz resonator. With the help of a transmon qubit, we measure the populations of the different resonator Fock states, thus providing reliable access to the temperature of the engineered electromagnetic environment and its effect on the resonator. We demonstrate coherent and thermal resonator states and that the on-demand dissipation provided by the QCR can drive these to a small fraction of a photon on average, even if starting above 1 K. We observe that the QCR can be operated either with a dc bias voltage or a gigahertz rf drive, or a combination of these. The bandwidth of the rf drive is not limited by the circuit itself and consequently, we show that 2.9 GHz continuous and 10 ns pulsed drives lead to identical desired refrigeration of the resonator. These observations answer to the shortcomings of previous works where the Fock states were not resolvable and the QCR exhibited slow charging dynamics. Thus, this work introduces a versatile tool to study open quantum systems, quantum thermodynamics, and to quickly reset superconducting qubits. Published by the American Physical Society 2024

arXiv:2308.00397•Physical Review Research•Jun 10, 2024•14 citations

Probing fast quantum circuit refrigeration in the quantum regime

Shuji Nakamura, Teruaki Yoshioka, S. A. Lemzyakov +8 more

Photon-absorption-based quantum circuit refrigeration is crucial to developing superconducting quantum computers, particularly for initializing qubits. However, precise and rapid measurement of residual photons in the circuit immediately after absorption has been a significant technical challenge. This study employs the ac Stark shift of superconducting qubits to detect sub-photon-level energies in the circuit, confirming the effectiveness of the fast refrigeration even in the quantum regime. These results will facilitate the development of more efficient quantum refrigeration devices and faster, high-fidelity qubit initialization.

arXiv:2407.14219•Physical Review Applied•Jan 10, 2025•6 citations

Recent Developments in Quantum‐Circuit Refrigeration

Timm Mörstedt, A.J. Viitanen, Vasilii Vadimov +7 more

Abstract The recent progress in direct active cooling of the quantum‐electric degrees of freedom in engineered circuits, or quantum‐circuit refrigeration is reviewed. In 2017, the discovery of a quantum‐circuit refrigerator (QCR) based on photon‐assisted tunneling of quasiparticles through normal‐metal–insulator–superconductor junctions inspired a series of experimental studies demonstrating the following main properties: i) the direct‐current (dc) bias voltage of the junction can change the QCR‐induced damping rate of a superconducting microwave resonator by orders of magnitude and give rise to nontrivial Lamb shifts, ii) the damping rate can be controlled in nanosecond time scales, and ii) the dc bias can be replaced by a microwave excitation, the amplitude of which controls the induced damping rate. Theoretically, it is predicted that state‐of‐the‐art superconducting resonators and qubits can be reset with an infidelity lower than 10−4 in tens of nanoseconds using experimentally feasible parameters. A QCR‐equipped resonator has also been demonstrated as an incoherent photon source with an output temperature above 1 K yet operating at millikelvin. This source has been used to calibrate cryogenic amplification chains. In the future, the QCR may be experimentally used to quickly reset superconducting qubits, and hence assist in the great challenge of building a practical quantum computer.

arXiv:2111.11234•Annalen der Physik•May 17, 2022•17 citations
The initialization of superconducting qubits is one of the essential techniques for the realization of quantum computation. In previous research, initialization above 99% fidelity has been achieved at 280 ns. Here, we demonstrate the rapid initialization of a superconducting qubit with a quantum circuit refrigerator (QCR). Photon-assisted tunneling of quasiparticles in the QCR can temporally increase the relaxation time of photons inside the resonator and helps release energy from the qubit to the environment. Experiments using this protocol have shown that 99% of initialization time is reduced to 200 ns. This initialization time depends strongly on the relaxation rate of the resonator, and faster initialization is possible by reducing the resistance of the QCR, which limits the on:off ratio, and by strengthening the coupling between the QCR and the resonator.
We present here our recent results on qubit reset scheme based on a quantum-circuit refrigerator (QCR). In particular, we use the photon-assisted quasiparticle tunneling through a superconductor–insulator–normal-metal–insulator–superconductor junction to controllably decrease the energy relaxation time of the qubit during the QCR operation. In our experiment, we use a transmon qubit with dispersive readout. The QCR is capacitively coupled to the qubit through its normal-metal island. We employ rapid, square-shaped QCR control voltage pulses with durations in the range of 2–350 ns and a variety of amplitudes to optimize the reset time and fidelity. Consequently, we reach a qubit ground-state probability of roughly 97% with 80-ns pulses starting from the first excited state. The qubit state probability is extracted from averaged readout signal, where the calibration is based on Rabi oscillations, thus not distinguishing the residual thermal population of the qubit.
In a quantum computation scheme, such as recycling a qubit, the initialization of the qubit is always required. At present, the initialization of the qubit is one of the bottlenecks in such computation, and high fidelity and fast initialization still remain important research subjects. In this study, by coupling a SINIS (superconductor–insulator–normal metal–insulator–superconductor) junction to a coupled system consisting of a qubit and a resonator, a photon is removed from the resonator by single-photon-assisted tunneling, and the effective relaxation rate of the resonator is increased. In addition, by applying an |e,0⟩−|f,0⟩ drive pulse and an |f,0⟩−|g,1⟩ drive pulse to the qubit, the energy of the qubit is rapidly transferred to the resonator to realize high-speed initialization. The present simulation shows that the qubit can be initialized with 99% fidelity in 80 ns and 99.9% in 137 ns when the electron temperature of the normal metal of the SINIS junction is 10 mK. The simulation also shows that the relaxation time of the qubit is about 13% longer when the resonator is interposed between the SINIS junction and the qubit than when the SINIS junction is directly coupled to the qubit.
We propose a quantum-circuit refrigerator (QCR) based on photon-assisted quasiparticle tunneling through a single normal-metal–insulator–superconductor (NIS) junction. In contrast to previous studies with multiple junctions and an additional charge island for the QCR, we directly connect the NIS junction to an inductively shunted electrode of a superconducting microwave resonator making the device immune to low-frequency charge noise. At low characteristic impedance of the resonator and parameters relevant to a recent experiment, we observe that a semiclassical impedance model of the NIS junction reproduces the bias voltage dependence of the QCR-induced damping rate and frequency shift. For high characteristic impedances, we derive a Born–Markov master equation and use it to observe significant non-linearities in the QCR-induced dissipation and frequency shift. We further demonstrate that, in this regime, the QCR can be used to initialize the linear resonator into a non-thermal state even in the absence of any microwave drive.
We experimentally demonstrate a recently proposed single-junction quantum-circuit refrigerator (QCR) as an tunable low-temperature environment for a superconducting 4.7 GHz resonator. With the help of a transmon qubit, we measure the populations of the different resonator Fock states, thus providing reliable access to the temperature of the engineered electromagnetic environment and its effect on the resonator. We demonstrate coherent and thermal resonator states and that the on-demand dissipation provided by the QCR can drive these to a small fraction of a photon on average, even if starting above 1 K. We observe that the QCR can be operated either with a dc bias voltage or a gigahertz rf drive, or a combination of these. The bandwidth of the rf drive is not limited by the circuit itself and consequently, we show that 2.9 GHz continuous and 10 ns pulsed drives lead to identical desired refrigeration of the resonator. These observations answer to the shortcomings of previous works where the Fock states were not resolvable and the QCR exhibited slow charging dynamics. Thus, this work introduces a versatile tool to study open quantum systems, quantum thermodynamics, and to quickly reset superconducting qubits. Published by the American Physical Society 2024
Photon-absorption-based quantum circuit refrigeration is crucial to developing superconducting quantum computers, particularly for initializing qubits. However, precise and rapid measurement of residual photons in the circuit immediately after absorption has been a significant technical challenge. This study employs the ac Stark shift of superconducting qubits to detect sub-photon-level energies in the circuit, confirming the effectiveness of the fast refrigeration even in the quantum regime. These results will facilitate the development of more efficient quantum refrigeration devices and faster, high-fidelity qubit initialization.
Abstract The recent progress in direct active cooling of the quantum‐electric degrees of freedom in engineered circuits, or quantum‐circuit refrigeration is reviewed. In 2017, the discovery of a quantum‐circuit refrigerator (QCR) based on photon‐assisted tunneling of quasiparticles through normal‐metal–insulator–superconductor junctions inspired a series of experimental studies demonstrating the following main properties: i) the direct‐current (dc) bias voltage of the junction can change the QCR‐induced damping rate of a superconducting microwave resonator by orders of magnitude and give rise to nontrivial Lamb shifts, ii) the damping rate can be controlled in nanosecond time scales, and ii) the dc bias can be replaced by a microwave excitation, the amplitude of which controls the induced damping rate. Theoretically, it is predicted that state‐of‐the‐art superconducting resonators and qubits can be reset with an infidelity lower than 10−4 in tens of nanoseconds using experimentally feasible parameters. A QCR‐equipped resonator has also been demonstrated as an incoherent photon source with an output temperature above 1 K yet operating at millikelvin. This source has been used to calibrate cryogenic amplification chains. In the future, the QCR may be experimentally used to quickly reset superconducting qubits, and hence assist in the great challenge of building a practical quantum computer.