Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2305.10956 · Scientific Reports

Fabrication of Al/AlOx/Al junctions with high uniformity and stability on sapphire substrates

Yuzhen Zheng, Shuming Li, Zengqian Ding, Kanglin Xiong, Jiagui Feng, Hui Yang

Published Jul 22, 2023• 12 citations
arXivHTMLPDF

Abstract

Abstract Tantalum and aluminum on sapphire are widely used platforms for qubits of long coherent time. As quantum chips scale up, the number of Josephson junctions on sapphire increases. Thus, both the uniformity and stability of the junctions are crucial to quantum devices, such as scalable superconducting quantum computer circuit, and quantum-limited amplifiers. By optimizing the fabrication process, especially, the conductive layer during the electron beam lithography process, Al/AlO x /Al junctions of sizes ranging from 0.0169 to 0.04 µm 2 on sapphire substrates were prepared. The relative standard deviation of room temperature resistances ( R N ) – $${\upsigma }_{{R_{{\text{N}}} }} /\left\langle {R_{{\text{N}}} } \right\rangle$$ σ R N / R N of these junctions is better than 1.7% on 15 mm × 15 mm chips, and better than 2.66% on 2 inch wafers, which is the highest uniformity on sapphire substrates has been reported. The junctions are robust and stable in resistances as temperature changes. The resistances increase by the ratio of 9.73% relative to R N as the temperature ramp down to 4 K, and restore their initial values in the reverse process as the temperature ramps back to room temperature. After being stored in a nitrogen cabinet for 100 days, the resistance of the junctions changed by1.16% on average. The demonstration of uniform and stable Josephson junctions in large area paves the way for the fabrication of superconducting chip of hundreds of qubits on sapphire substrates.

DOI
10.1038/s41598-023-39052-2

Related papers

Manufacturing of Superconducting Qubits Using Nb/Al-AlO x /Nb Josephson Junctions on Silicon Substrate

Qingjian Li, Y. F. Wu, Zhengqi Niu +4 more

Superconducting qubits stand as a pivotal platform for quantum computing, where scalable fabrication is crucial for building complex quantum circuits. Here, we develop a fabrication process for Nb/Al-AlOx/Nb tri-layer Josephson junctions on 4-inch silicon wafers using full-stepper lithography. Utilizing this process, we have produced both transmon and C-shunt flux qubits. The well-behavedI-Vcharacteristics of junction arrays containing up to 1000 junctions highlight the excellent uniformity and scalability of our process. Furthermore, by introducing a RIE pre-etch before BOE treatment to remove most of the SiO2insulator, we have suppressed dielectric loss and increased the coherence time of the Nb-based transmon qubit by almost 10 times, achieving a quality factor comparable to state-of-the-art Nb-based qubits on sapphire substrates. Given its compatibility with silicon technology, our method paves the way for the integration of multi-qubit processors and the co-fabrication of complex quantum circuits.

IEEE Transactions on Applied Superconductivity•Jan 28, 2026•1 citation

Aluminum Josephson junction microstructure and electrical properties modified by thermal annealing

Nikita D. Korshakov, Dmitry O. Moskalev, Anastasia A. Soloveva +7 more

Reproducibility of Al/AlO x /Al Josephson junctions is a challenge for scaling up superconducting quantum processors. The frequency uncertainty of the transmon qubits arising from the fabrication process is attributed to deviations in the Josephson junction microstructure and electrical properties. Here, we present a solution for this problem using the post-fabrication Josephson junction thermal annealing process. The developed thermal post-exposure method allows not only to increase the junction resistance by 175%, but also to decrease by 60% with a step of 10% in R n , which opens up new possibilities for tuning the frequency of qubits. The resistance is shown to be strongly temperature dependent, and is weakly dependent on the holding time. The linear dimensions of the electrodes and the sidewalls contribution to the total JJ area also have a significant impact on the final resistance after annealing. Finally, a theoretical model of the structure modification in a tunnel barrier with changes in oxygen concentration gradient is proposed. The proposed thermal annealing approach can be used to form stable and reproducible tunnel barriers and scalable frequency trimming for widely used fixed-frequency transmon qubits.

arXiv:2403.02179•Scientific Reports•Oct 30, 2024•14 citations

Optimization of shadow evaporation and oxidation for reproducible quantum Josephson junction circuits

Dmitry O. Moskalev, E. V. Zikiy, Anastasiya A. Pishchimova +5 more

Abstract The most commonly used physical realization of superconducting qubits for quantum circuits is a transmon. There are a number of superconducting quantum circuits applications, where Josephson junction critical current reproducibility over a chip is crucial. Here, we report on a robust chip scale Al/AlO x /Al junctions fabrication method due to comprehensive study of shadow evaporation and oxidation steps. We experimentally demonstrate the evidence of optimal Josephson junction electrodes thickness, deposition rate and deposition angle, which ensure minimal electrode surface and line edge roughness. The influence of oxidation method, pressure and time on critical current reproducibility is determined. With the proposed method we demonstrate Al/AlO x /Al junction fabrication with the critical current variation $$(\sigma /\langle {I_{c} } \rangle )$$ ( σ / ⟨ I c ⟩ ) less than 3.9% (from 150 × 200 to 150 × 600 nm 2 area) and 7.7% (for 100 × 100 nm 2 area) over 20 × 20 mm 2 chip. Finally, we fabricate separately three 5 × 10 mm 2 chips with 18 transmon qubits (near 4.3 GHz frequency) showing less than 1.9% frequency variation between qubits on different chips. The proposed approach and optimization criteria can be utilized for a robust wafer-scale superconducting qubit circuits fabrication.

arXiv:2212.06692•Scientific Reports•Mar 13, 2023•47 citations

Fabrication of Al/AlOx/Al Josephson junctions and superconducting quantum circuits by shadow evaporation and a dynamic oxidation process

Yulin Wu, Hui Deng, Haifeng Yu +6 more

Besides serving as promising candidates for realizing quantum computing, superconducting quantum circuits are one of a few macroscopic physical systems in which fundamental quantum phenomena can be directly demonstrated and tested, giving rise to a vast field of intensive research work both theoretically and experimentally. In this paper we report our work on the fabrication of superconducting quantum circuits, starting from its building blocks: Al/AlO x /Al Josephson junctions. By using electron beam lithography patterning and shadow evaporation, we have fabricated aluminum Josephson junctions with a controllable critical current density ( j c ) and wide range of junction sizes from 0.01 μm 2 up to 1 μm 2 . We have carried out systematical studies on the oxidation process in fabricating Al/AlO x /Al Josephson junctions suitable for superconducting flux qubits. Furthermore, we have also fabricated superconducting quantum circuits such as superconducting flux qubits and charge-flux qubits.

Chinese Physics B•Jun 1, 2013•19 citations

Uniformity improvement of Josephson-junction resistance by considering sidewall deposition during shadow evaporation for large-scale integration of qubits

Tsuyoshi Takahashi, Norinao Kouma, Yoshiyasu Doi +3 more

Abstract The uniformity of Josephson-junction (JJ) characteristics is crucial in wafer-scale superconducting quantum-bit (qubit) integration. To achieve the level of accuracy demanded the circuits, every detail of the fabrication process needs to be optimized. Here we reveal that the junction-resistance (R N) variations of Al/AlO x /Al JJs are affected by the metal deposition on the sidewall of the resist mask during shadow evaporation. The effect is reproduced in numerical simulation using a simple model taking into account the resist structure and the evaporation angle. To overcome the issue, we introduce a two-step shadow evaporation method to reduce the variation of R N. As a result, the coefficient of variations across a 3-inch wafer decreases from 6.7% to 4.5%, achieving 1.1% in a chip with an area of 10 mm × 10 mm. This method is promising for developing large-scale superconducting quantum computers.

Japanese Journal of Applied Physics•Nov 14, 2022•13 citations

Simplified Josephson-junction fabrication process for reproducibly high-performance superconducting qubits

Amr Osman, J. Simon, Andreas Bengtsson +7 more

We introduce a simplified fabrication technique for Josephson junctions and demonstrate superconducting Xmon qubits with T1 relaxation times averaging above 50 μs (Q>1.5×106). Current shadow-evaporation techniques for aluminum-based Josephson junctions require a separate lithography step to deposit a patch that makes a galvanic, superconducting connection between the junction electrodes and the circuit wiring layer. The patch connection eliminates parasitic junctions, which otherwise contribute significantly to dielectric loss. In our patch-integrated cross-type junction technique, we use one lithography step and one vacuum cycle to evaporate both the junction electrodes and the patch. This eliminates a key bottleneck in manufacturing superconducting qubits by reducing the fabrication time and cost. In a study of more than 3600 junctions, we show an average resistance variation of 3.7% on a wafer that contains forty 0.5×0.5-cm2 chips, with junction areas ranging between 0.01 and 0.16 μm2. The average on-chip spread in resistance is 2.7%, with 20 chips varying between 1.4% and 2%. For the junction sizes used for transmon qubits, we deduce a wafer-level transition-frequency variation of 1.7%–2.5%. We show that 60%–70% of this variation is attributed to junction-area fluctuations, while the rest is caused by tunnel-junction inhomogeneity. Such high frequency predictability is a requirement for scaling-up the number of qubits in a quantum computer.

arXiv:2011.05230•Applied Physics Letters•Feb 8, 2021•104 citations
Abstract Tantalum and aluminum on sapphire are widely used platforms for qubits of long coherent time. As quantum chips scale up, the number of Josephson junctions on sapphire increases. Thus, both the uniformity and stability of the junctions are crucial to quantum devices, such as scalable superconducting quantum computer circuit, and quantum-limited amplifiers. By optimizing the fabrication process, especially, the conductive layer during the electron beam lithography process, Al/AlO x /Al junctions of sizes ranging from 0.0169 to 0.04 µm 2 on sapphire substrates were prepared. The relative standard deviation of room temperature resistances ( R N ) – \upsigmaRN/⟨RN⟩{\upsigma }_{{R_{{\text{N}}} }} /\left\langle {R_{{\text{N}}} } \right\rangle\upsigmaRN​​/⟨RN​⟩ σ R N / R N of these junctions is better than 1.7% on 15 mm × 15 mm chips, and better than 2.66% on 2 inch wafers, which is the highest uniformity on sapphire substrates has been reported. The junctions are robust and stable in resistances as temperature changes. The resistances increase by the ratio of 9.73% relative to R N as the temperature ramp down to 4 K, and restore their initial values in the reverse process as the temperature ramps back to room temperature. After being stored in a nitrogen cabinet for 100 days, the resistance of the junctions changed by1.16% on average. The demonstration of uniform and stable Josephson junctions in large area paves the way for the fabrication of superconducting chip of hundreds of qubits on sapphire substrates.
Superconducting qubits stand as a pivotal platform for quantum computing, where scalable fabrication is crucial for building complex quantum circuits. Here, we develop a fabrication process for Nb/Al-AlOx/Nb tri-layer Josephson junctions on 4-inch silicon wafers using full-stepper lithography. Utilizing this process, we have produced both transmon and C-shunt flux qubits. The well-behavedI-Vcharacteristics of junction arrays containing up to 1000 junctions highlight the excellent uniformity and scalability of our process. Furthermore, by introducing a RIE pre-etch before BOE treatment to remove most of the SiO2insulator, we have suppressed dielectric loss and increased the coherence time of the Nb-based transmon qubit by almost 10 times, achieving a quality factor comparable to state-of-the-art Nb-based qubits on sapphire substrates. Given its compatibility with silicon technology, our method paves the way for the integration of multi-qubit processors and the co-fabrication of complex quantum circuits.
Reproducibility of Al/AlO x /Al Josephson junctions is a challenge for scaling up superconducting quantum processors. The frequency uncertainty of the transmon qubits arising from the fabrication process is attributed to deviations in the Josephson junction microstructure and electrical properties. Here, we present a solution for this problem using the post-fabrication Josephson junction thermal annealing process. The developed thermal post-exposure method allows not only to increase the junction resistance by 175%, but also to decrease by 60% with a step of 10% in R n , which opens up new possibilities for tuning the frequency of qubits. The resistance is shown to be strongly temperature dependent, and is weakly dependent on the holding time. The linear dimensions of the electrodes and the sidewalls contribution to the total JJ area also have a significant impact on the final resistance after annealing. Finally, a theoretical model of the structure modification in a tunnel barrier with changes in oxygen concentration gradient is proposed. The proposed thermal annealing approach can be used to form stable and reproducible tunnel barriers and scalable frequency trimming for widely used fixed-frequency transmon qubits.
Abstract The most commonly used physical realization of superconducting qubits for quantum circuits is a transmon. There are a number of superconducting quantum circuits applications, where Josephson junction critical current reproducibility over a chip is crucial. Here, we report on a robust chip scale Al/AlO x /Al junctions fabrication method due to comprehensive study of shadow evaporation and oxidation steps. We experimentally demonstrate the evidence of optimal Josephson junction electrodes thickness, deposition rate and deposition angle, which ensure minimal electrode surface and line edge roughness. The influence of oxidation method, pressure and time on critical current reproducibility is determined. With the proposed method we demonstrate Al/AlO x /Al junction fabrication with the critical current variation (σ/⟨Ic⟩)(\sigma /\langle {I_{c} } \rangle )(σ/⟨Ic​⟩) ( σ / ⟨ I c ⟩ ) less than 3.9% (from 150 × 200 to 150 × 600 nm 2 area) and 7.7% (for 100 × 100 nm 2 area) over 20 × 20 mm 2 chip. Finally, we fabricate separately three 5 × 10 mm 2 chips with 18 transmon qubits (near 4.3 GHz frequency) showing less than 1.9% frequency variation between qubits on different chips. The proposed approach and optimization criteria can be utilized for a robust wafer-scale superconducting qubit circuits fabrication.
Besides serving as promising candidates for realizing quantum computing, superconducting quantum circuits are one of a few macroscopic physical systems in which fundamental quantum phenomena can be directly demonstrated and tested, giving rise to a vast field of intensive research work both theoretically and experimentally. In this paper we report our work on the fabrication of superconducting quantum circuits, starting from its building blocks: Al/AlO x /Al Josephson junctions. By using electron beam lithography patterning and shadow evaporation, we have fabricated aluminum Josephson junctions with a controllable critical current density ( j c ) and wide range of junction sizes from 0.01 μm 2 up to 1 μm 2 . We have carried out systematical studies on the oxidation process in fabricating Al/AlO x /Al Josephson junctions suitable for superconducting flux qubits. Furthermore, we have also fabricated superconducting quantum circuits such as superconducting flux qubits and charge-flux qubits.
Abstract The uniformity of Josephson-junction (JJ) characteristics is crucial in wafer-scale superconducting quantum-bit (qubit) integration. To achieve the level of accuracy demanded the circuits, every detail of the fabrication process needs to be optimized. Here we reveal that the junction-resistance (R N) variations of Al/AlO x /Al JJs are affected by the metal deposition on the sidewall of the resist mask during shadow evaporation. The effect is reproduced in numerical simulation using a simple model taking into account the resist structure and the evaporation angle. To overcome the issue, we introduce a two-step shadow evaporation method to reduce the variation of R N. As a result, the coefficient of variations across a 3-inch wafer decreases from 6.7% to 4.5%, achieving 1.1% in a chip with an area of 10 mm × 10 mm. This method is promising for developing large-scale superconducting quantum computers.
We introduce a simplified fabrication technique for Josephson junctions and demonstrate superconducting Xmon qubits with T1 relaxation times averaging above 50 μs (Q>1.5×106). Current shadow-evaporation techniques for aluminum-based Josephson junctions require a separate lithography step to deposit a patch that makes a galvanic, superconducting connection between the junction electrodes and the circuit wiring layer. The patch connection eliminates parasitic junctions, which otherwise contribute significantly to dielectric loss. In our patch-integrated cross-type junction technique, we use one lithography step and one vacuum cycle to evaporate both the junction electrodes and the patch. This eliminates a key bottleneck in manufacturing superconducting qubits by reducing the fabrication time and cost. In a study of more than 3600 junctions, we show an average resistance variation of 3.7% on a wafer that contains forty 0.5×0.5-cm2 chips, with junction areas ranging between 0.01 and 0.16 μm2. The average on-chip spread in resistance is 2.7%, with 20 chips varying between 1.4% and 2%. For the junction sizes used for transmon qubits, we deduce a wafer-level transition-frequency variation of 1.7%–2.5%. We show that 60%–70% of this variation is attributed to junction-area fluctuations, while the rest is caused by tunnel-junction inhomogeneity. Such high frequency predictability is a requirement for scaling-up the number of qubits in a quantum computer.