We demonstrate a 3-port Josephson parametric circulator matched to 50 Ω using second order Chebyshev networks. The device notably operates with two of its signal ports at the same frequency and uses only two out-of-phase pumps at a single frequency. As a consequence, when operated as an isolator, it does not require phase coherence between the pumps and the signal, thus simplifying the requirements for its integration into standard dispersive qubit readout setups. The device utilizes parametric couplers based on a balanced bridge of rf-superconducting quantum interference device arrays, which offer purely parametric coupling and high dynamic range. We characterize the device by measuring its full 3 × 3 S-matrix as a function of frequency and the relative phase between the two pumps. We find up to 15 dB nonreciprocity over a 200 MHz signal band, port match better than 10 dB, low insertion loss of 0.6 dB, and saturation power exceeding −80 dBm.
We demonstrate a 3-port Josephson parametric circulator matched to 50 Ω using second order Chebyshev networks. The device notably operates with two of its signal ports at the same frequency and uses only two out-of-phase pumps at a single frequency. As a consequence, when operated as an isolator, it does not require phase coherence between the pumps and the signal, thus simplifying the requirements for its integration into standard dispersive qubit readout setups. The device utilizes parametric couplers based on a balanced bridge of rf-superconducting quantum interference device arrays, which offer purely parametric coupling and high dynamic range. We characterize the device by measuring its full 3 × 3 S-matrix as a function of frequency and the relative phase between the two pumps. We find up to 15 dB nonreciprocity over a 200 MHz signal band, port match better than 10 dB, low insertion loss of 0.6 dB, and saturation power exceeding −80 dBm.
We demonstrate a Josephson parametric amplifier design with a band-pass impedance-matching network based on a third-order Chebyshev prototype. We measured eight amplifiers operating at 4.6 GHz that exhibit gains of 20 dB with less than 1-dB gain ripple and bandwidth up to 500 MHz. The amplifiers further achieve high-output-saturation powers around $\ensuremath{-}73\phantom{\rule{0.2em}{0ex}}\mathrm{dBm}$ based on the use of rf superconducting quantum interference device arrays as their nonlinear element. We characterize the system readout efficiency and its signal-to-noise ratio near saturation using a Sycamore processor, finding the data consistent with near quantum limited noise performance of the amplifiers. In addition, we measure the amplifiers' intermodulation distortion in two-tone experiments as a function of input power and intertone detuning, and observe excess distortion at small detuning with a pronounced dip as a function of signal power, which we interpret in terms of power-dependent dielectric losses.
Abstract In quantum information detection, significant interest has recently emerged in replacing conventional ferrite circulators with superconducting magnetic-free nonreciprocal devices. However, superconducting non-reciprocal devices with simpler structures and easier manufacturing processes still require further development. Inspired by conventional microwave circuits, we demonstrate a superconducting nonreciprocal circulator by parametric modulation of three identical, strongly and symmetrically coupled resonators. The circulator requires only three DC superconducting quantum interference devices, achieving an isolation of 20 dB , insertion loss of 0.47 dB , and return loss better than 25 dB over an instantaneous bandwidth of 50 MHz . The center frequency of the circulator is tunable within the range of 4– 8 GHz . Detailed design considerations for the experimental realization of a three-port superconducting circulator are presented, together with simulation results for a four-port circulator. Compared with previously reported superconducting magnetic-free nonreciprocal devices, the proposed circulator features a simpler circuit topology, demonstrating strong potential for scalable superconducting quantum information detection.
High-fidelity quantum nondemolition qubit measurement is critical to error correction and rapid qubit feedback in large-scale quantum computing. Maximizing high-fidelity dispersive readout in superconducting qubits commonly requires passing a short and strong pulse through the qubit's readout resonator, which is then processed by a sufficiently high bandwidth, high saturation power, and quantum-limited amplifier. We have developed an amplifier design pipeline that combines time-domain simulation of the untruncated device Hamiltonian, fabrication constraints, and maximization of saturation power. We have realized an amplifier based on a modified trilayer (Nb-Al-AlOx-Nb) fabrication suite at NIST, which utilizes an array of 25 rf superconducting quantum interference devices embedded within a low-Q resonator powered by a high-power voltage pump delivered via a diplexer on the signal port. We show that, despite the intensity of the pump, the device is quantum efficient and capable of high-fidelity measurement limited by state transitions in the transmon. We present experimental data demonstrating up to $\ensuremath{-}91.2\phantom{\rule{0.2em}{0ex}}\mathrm{dBm}$ input saturation power with 20-dB gain, up to 28-MHz instantaneous bandwidth, and phase-preserving qubit measurements with $62\mathrm{%}$ quantum efficiency.
The cryogenic hardware required to build a superconducting-qubit-based quantum computer demands a variety of microwave components. These elements include microwave couplers, filters, amplifiers, and circulators and/or isolators. Traditionally implemented as discrete components, integration of this peripheral hardware, in an effort to reduce overall footprint, thermal load, and added noise, is a key challenge to scaling modern quantum processors with qubit counts climbing over the one hundred plus mark. Ferrite-based microwave isolators, generally employed in the readout chain to decouple qubits and resonators from readout electronics, persist as one of the volumetrically largest devices still utilized as discrete components. Here, we present an alternative two-port isolating integrated circuit derived from the dc superconducting quantum interference device (dc SQUID). Nonreciprocal transmission is achieved using the three-wave microwave-mixing properties of a flux-modulated dc SQUID. We show that when multiple dc SQUIDs are embedded in a multipole admittance-inverting filter structure, the three-wave mixing derived from the flux pumping of the dc SQUIDs can provide directional microwave power flow. For a three-pole filter device, we experimentally demonstrate a directionality greater than 15 dB over a 600-MHz bandwidth.
Abstract Nonreciprocal microwave devices play critical roles in high-fidelity, quantum-nondemolition (QND) measurement schemes. They impose unidirectional routing of readout signals and protect the quantum systems from unwanted noise originated by the output chain. However, cryogenic circulators and isolators are disadvantageous in scalable superconducting architectures because they use magnetic materials and strong magnetic fields. Here, we realize an active isolator formed by coupling two nondegenerate Josephson mixers in an interferometric scheme and driving them with phase-shifted, same-frequency pumps. By incorporating our Josephson-based isolator into a superconducting qubit setup, we demonstrate fast, high-fidelity, QND measurements of the qubit while providing 20 dB of protection within a bandwidth of 10 MHz against amplified noise reflected off the Josephson amplifier in the output chain. A moderate reduction of 35% is observed in T2E when the Josephson-based isolator is turned on. Such a moderate degradation can be mitigated by minimizing heat dissipation in the pump lines.
Nonreciprocal microwave devices, such as circulators and isolators, are needed in high-fidelity qubit readout schemes to unidirectionally route the readout signals and protect the qubits against noise coming from the output chain.However, cryogenic circulators and isolators are prohibitive in scalable superconducting architectures because they rely on magnetic materials.Here we report a fast (750 ns) high-fidelity (95%) quantum nondemolition readout of a coherent superconducting qubit (T 1 = 52 μs, T 2E = 35 μs) without any nonreciprocal magnetic devices.We use in our readout chain a microwave-controlled qubit readout multichip module (QRMCM) that integrates interferometric directional Josephson devices consisting of an isolator and a reconfigurable isolator or amplifier device, and an off-chip low-pass filter.Using the QRMCM, we demonstrate isolation up to 45 dB within 13 MHz, when both directional devices are operated as isolators, and low-noise amplification in excess of 10 dB within a dynamical bandwidth of 10 MHz, when the reconfigurable device is operated as an amplifier.We also investigate the dependence of the qubit coherence times T ϕ and T 2E on the isolation response of the QRMCM, which we control in situ using the microwave drives feeding the isolators.Furthermore, by directly comparing the QRMCM performance with that of a state-of-art configuration (with T 2E ≈ 2T 1 ) that uses a pair of wideband magnetic isolators, we find that the excess pure dephasing measured with the QRMCM (for which T 2E ≈ T 1 ) is likely limited by the residual thermal photon population in the readout resonator.Improved versions of the QRMCM could replace magnetic circulators and isolators in large superconducting quantum processors.