The cryogenic hardware required to build a superconducting-qubit-based quantum computer demands a variety of microwave components. These elements include microwave couplers, filters, amplifiers, and circulators and/or isolators. Traditionally implemented as discrete components, integration of this peripheral hardware, in an effort to reduce overall footprint, thermal load, and added noise, is a key challenge to scaling modern quantum processors with qubit counts climbing over the one hundred plus mark. Ferrite-based microwave isolators, generally employed in the readout chain to decouple qubits and resonators from readout electronics, persist as one of the volumetrically largest devices still utilized as discrete components. Here, we present an alternative two-port isolating integrated circuit derived from the dc superconducting quantum interference device (dc SQUID). Nonreciprocal transmission is achieved using the three-wave microwave-mixing properties of a flux-modulated dc SQUID. We show that when multiple dc SQUIDs are embedded in a multipole admittance-inverting filter structure, the three-wave mixing derived from the flux pumping of the dc SQUIDs can provide directional microwave power flow. For a three-pole filter device, we experimentally demonstrate a directionality greater than 15 dB over a 600-MHz bandwidth.
The cryogenic hardware required to build a superconducting-qubit-based quantum computer demands a variety of microwave components. These elements include microwave couplers, filters, amplifiers, and circulators and/or isolators. Traditionally implemented as discrete components, integration of this peripheral hardware, in an effort to reduce overall footprint, thermal load, and added noise, is a key challenge to scaling modern quantum processors with qubit counts climbing over the one hundred plus mark. Ferrite-based microwave isolators, generally employed in the readout chain to decouple qubits and resonators from readout electronics, persist as one of the volumetrically largest devices still utilized as discrete components. Here, we present an alternative two-port isolating integrated circuit derived from the dc superconducting quantum interference device (dc SQUID). Nonreciprocal transmission is achieved using the three-wave microwave-mixing properties of a flux-modulated dc SQUID. We show that when multiple dc SQUIDs are embedded in a multipole admittance-inverting filter structure, the three-wave mixing derived from the flux pumping of the dc SQUIDs can provide directional microwave power flow. For a three-pole filter device, we experimentally demonstrate a directionality greater than 15 dB over a 600-MHz bandwidth.
Nonreciprocal microwave devices, such as circulators and isolators, are needed in high-fidelity qubit readout schemes to unidirectionally route the readout signals and protect the qubits against noise coming from the output chain.However, cryogenic circulators and isolators are prohibitive in scalable superconducting architectures because they rely on magnetic materials.Here we report a fast (750 ns) high-fidelity (95%) quantum nondemolition readout of a coherent superconducting qubit (T 1 = 52 μs, T 2E = 35 μs) without any nonreciprocal magnetic devices.We use in our readout chain a microwave-controlled qubit readout multichip module (QRMCM) that integrates interferometric directional Josephson devices consisting of an isolator and a reconfigurable isolator or amplifier device, and an off-chip low-pass filter.Using the QRMCM, we demonstrate isolation up to 45 dB within 13 MHz, when both directional devices are operated as isolators, and low-noise amplification in excess of 10 dB within a dynamical bandwidth of 10 MHz, when the reconfigurable device is operated as an amplifier.We also investigate the dependence of the qubit coherence times T ϕ and T 2E on the isolation response of the QRMCM, which we control in situ using the microwave drives feeding the isolators.Furthermore, by directly comparing the QRMCM performance with that of a state-of-art configuration (with T 2E ≈ 2T 1 ) that uses a pair of wideband magnetic isolators, we find that the excess pure dephasing measured with the QRMCM (for which T 2E ≈ T 1 ) is likely limited by the residual thermal photon population in the readout resonator.Improved versions of the QRMCM could replace magnetic circulators and isolators in large superconducting quantum processors.
Abstract In quantum information detection, significant interest has recently emerged in replacing conventional ferrite circulators with superconducting magnetic-free nonreciprocal devices. However, superconducting non-reciprocal devices with simpler structures and easier manufacturing processes still require further development. Inspired by conventional microwave circuits, we demonstrate a superconducting nonreciprocal circulator by parametric modulation of three identical, strongly and symmetrically coupled resonators. The circulator requires only three DC superconducting quantum interference devices, achieving an isolation of 20 dB , insertion loss of 0.47 dB , and return loss better than 25 dB over an instantaneous bandwidth of 50 MHz . The center frequency of the circulator is tunable within the range of 4– 8 GHz . Detailed design considerations for the experimental realization of a three-port superconducting circulator are presented, together with simulation results for a four-port circulator. Compared with previously reported superconducting magnetic-free nonreciprocal devices, the proposed circulator features a simpler circuit topology, demonstrating strong potential for scalable superconducting quantum information detection.
We propose a design to realize integrated broadband nonreciprocal microwave isolators and circulators using superconducting circuit elements without any magnetic materials. To obtain a broadband response, we develop a waveguide-based design by temporal modulations. The corresponding compact traveling-wave structure is implemented with integrated superconducting composite right-/left-handed transmission lines. The calculations show that the bandwidth of 580 MHz can be realized over a nonreciprocal isolation of 20 dB in reflections. Such on-chip isolators and circulators are useful for cryogenic integrated microwave connections and measurements, such as protecting qubits from the amplified reflected signal in multiplexed readout.
Nonreciprocal microwave routing plays a crucial role in measuring quantum circuits, and allows for realizing cascaded quantum systems for generating and stabilizing entanglement between noninteracting qubits. The most commonly used tools for implementing directionality are ferrite-based circulators. These devices are versatile, but suffer from excess loss, a large footprint, and fixed directionality. For utilizing nonreciprocity in scalable quantum circuits it is desirable to develop efficient integration of low-loss and controllable directional elements. Here, we report the design and experimental realization of a minimal controllable directional interface that can be directly coupled to superconducting qubits. In the device presented, nonreciprocity is realized through a combination of interference and phase-controlled parametric pumping. We have achieved a maximum directionality of around 30 dB, and the performance of the device is predicted quantitatively from independent calibration measurements. Using the excellent agreement of model and experiment, we predict that the circuit will be useable as a chiral qubit interface with inefficiencies at the 1 % level or below. Our work offers a promising route for realizing high-fidelity signal routing and entanglement generation in all-to-all connected microwave quantum networks, and provides a path for isolator-free qubit readout schemes. Published by the American Physical Society 2024
Microwave filtering for superconducting qubits is a key element of quantum computing technology, enabling high coherence and fast state detection. This work presents the design and implementation of novel microwave Purcell filters for superconducting quantum circuits, integrated within a multilayer printed circuit board (PCB). The off-chip design removes all filter components from the qubit substrate, reducing device complexity, improving layout footprint and allowing better scalability to large qubit counts. Each embedded filter can couple up to nine readout resonators, enabling efficient multiplexed readout. Electromagnetic simulations of the filter predict a thousand-fold improvement in qubit isolation from the readout port. The design was experimentally validated under cryogenic conditions in conjunction with a 35-qubit device, demonstrating compatibility of the PCB-based filter with high-coherence superconducting qubits. The comparison of the measured qubit median T1 of 84 μs with the expected radiative limit from electromagnetic simulations validated the presence of Purcell filtering in the system.
One of the primary requirements for superconducting quantum information processors is high-fidelity, quantum non-demolition qubit readout. In superconducting circuits, we perform measurements with quantum-limited microwave amplifiers. These amplifiers are based on microwave cavities and powered by Josephson-junction based nonlinearities, which we drive to parametrically modulate the circuit and generate gain. However, cavity-based amplifiers generally suffer from a fixed gain-bandwidth product, a limited dynamic range, and the absence of directionality, and so they must be operated with external lossy microwave commercial components such as circulators. Many of these limitations can be circumvented by combining multiple parametric processes in a few-mode device, in particular by combining parametric drives which produce gain and those which produce gainless photon conversion. By combining balanced gain and conversion processes between a pair of modes, we have demonstrated transmission-only, phase-sensitive, gain-bandwidth-free amplification. We have also used measurements of transmon qubits with this mode of amplification to demonstrate its practical utility. More, by combining multiple instances of imbalanced gain and conversion processes among three modes, we have realized devices with non-reciprocal, transmission-only amplification, matched ports, and a large, gain-independent bandwidth. One of the biggest challenges in tuning multiple parametric processes is both inherent and dynamically-generated higher order nonlinearities in the device, which shift mode frequencies and parametric coupling strengths with pump power, preventing accurate balancing of the parametric processes. These can be controlled through engineering the Hamiltonian of the nonlinear element, in this thesis either a linearly-shunted Josephson Ring Modulator or SNAIL (Superconducting Nonlinear Asymmetric Inductive eLements), which for certain applied flux values can minimize or even change the sign of higher-order even nonlinearities. Additionally, we have explored a range of circuit parameters, allowing us to also control the relative size of odd-order nonlinearities. We have developed a series of prototypes which implement these concepts, and have achieved both high-dynamic range singly pumped amplifiers, and a promising platform for multi-parametric devices. We conclude by presenting recent progress towards implementing multiple parametric schemes that generates a practical directional amplifier, and discuss the remaining obstacles to a truly ideal parametric amplifiers.