Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1603.04848 · Review of Scientific Instruments

Piezoelectric tunable microwave superconducting cavity

Natália C. Carvalho, Yaohui Fan, Michael Edmund Tobar

Published Sep 1, 2016• 23 citations
arXivHTMLPDF

Abstract

In the context of engineered quantum systems, there is a demand for superconducting tunable devices, able to operate with high-quality factors at power levels equivalent to only a few photons. In this work, we developed a 3D microwave re-entrant cavity with such characteristics ready to provide a very fine-tuning of a high-Q resonant mode over a large dynamic range. This system has an electronic tuning mechanism based on a mechanically amplified piezoelectric actuator, which controls the resonator dominant mode frequency by changing the cavity narrow gap by very small displacements. Experiments were conducted at room and dilution refrigerator temperatures showing a large dynamic range up to 4 GHz and 1 GHz, respectively, and were compared to a finite element method model simulated data. At elevated microwave power input, nonlinear thermal effects were observed to destroy the superconductivity of the cavity due to the large electric fields generated in the small gap of the re-entrant cavity.

DOI
10.1063/1.4962695

Related papers

Tuning a 3D microwave cavity via superfluid helium at millikelvin temperatures

Fabien Souris, H. Christiani, J. P. Davis

Frequency tunability of three dimensional (3D) microwave cavities opens up numerous possibilities for their use in hybrid quantum systems and related technologies. For many applications, it is desirable to tune the resonance at cryogenic temperatures without mechanical actuation. We show that a superconducting 3D microwave cavity can be tuned at the percent level by taking advantage of the dielectric properties of superfluid 4He at millikelvin temperatures, without affecting its intrinsic quality factor—reaching 3 × 105 in the present experiment.

arXiv:1707.09469•Applied Physics Letters•Oct 23, 2017•17 citations

Cryogenic microwave filter cavity with a tunability greater than 5 GHz

Thomas J. Clark, Vaisakh Vadakkumbatt, Fabien Souris +2 more

A wide variety of applications of microwave cavities, such as measurement and control of superconducting qubits, magnonic resonators, and phase noise filters, would be well served by having a highly tunable microwave resonance. Often this tunability is desired in situ at low temperatures, where one can take advantage of superconducting cavities. To date, such cryogenic tuning while maintaining a high quality factor has been limited to ∼500 MHz. Here we demonstrate a three-dimensional superconducting microwave cavity that shares one wall with a pressurized volume of helium. Upon pressurization of the helium chamber, the microwave cavity is deformed, which results in in situ tuning of its resonant frequency by more than 5 GHz, greater than 60% of the original 8 GHz resonant frequency. The quality factor of the cavity remains approximately constant at ≈7 × 103 over the entire range of tuning. As a demonstration of its usefulness, we implement a tunable cryogenic phase noise filter, which reduces the phase noise of our source by approximately 10 dB above 400 kHz.

arXiv:1810.02404•Review of Scientific Instruments•Nov 1, 2018•15 citations

Applications of Superconducting Re-Entrant Microwave Cavities

Thomas J. Clark

This thesis describes the design, fabrication, and characterization of 3D superconducting microwave cavities for two applications. It first describes a cryogenically compatible microwave filter that is able to tune its resonant frequency by an unprecedented 5 GHz via deformation caused by a a helium pressure vessel. Then, it describes a novel microwave optomechanics device where such a cavity is coupled to an aluminized SiN membrane. It demonstrates that this device can be back-action cooled from the 450 mK base temperature of the cryostat down to 160 mK.

•Jan 1, 2019•0 citations

Flux-tunable heat sink for quantum electric circuits

Matti Partanen, Kuan Yen Tan, Shumpei Masuda +10 more

Abstract Superconducting microwave circuits show great potential for practical quantum technological applications such as quantum information processing. However, fast and on-demand initialization of the quantum degrees of freedom in these devices remains a challenge. Here, we experimentally implement a tunable heat sink that is potentially suitable for the initialization of superconducting qubits. Our device consists of two coupled resonators. The first resonator has a high quality factor and a fixed frequency whereas the second resonator is designed to have a low quality factor and a tunable resonance frequency. We engineer the low quality factor using an on-chip resistor and the frequency tunability using a superconducting quantum interference device. When the two resonators are in resonance, the photons in the high-quality resonator can be efficiently dissipated. We show that the corresponding loaded quality factor can be tuned from above 105 down to a few thousand at 10 GHz in good quantitative agreement with our theoretical model.

arXiv:1712.10256•Scientific Reports•Apr 16, 2018•4 citations

Tunable superconducting transmissionline resonator for qubit coupling

Martin Sandberg

In this licentiate thesis design, fabrication, and measurements of tunable superconducting microwave transmission line resonators are described. The resonators are of quarter wavelength type were the tuning is achieved by changing one of the boundary conditions of the resonator through a tunable impedance. As tunable impedance the Josephson inductance in form of SQUIDs is used. The Josephson inductance can then be tuned by applying a magnetic field to the SQUID loop. A tuning range of 750 MHz for a 5 GHz resonator is achieved, and as a figure of merit it can be tuned over 200 line widths. The purpose of the tunable resonators is to use them for dynamic coupling of superconducting quantum bits, this requires that the resonators can be tuned fast on the timescale of the resonator-qubit coupling. To measure tuning speeds faster then the ring up time of the resonators a method that measures the leakage of energy out of a detuned resonator was developed. With this method a frequency shift of the energy stored in the resonator can be measured. A detuning of 330 MHz in less than 10 ns is demonstrated for a 4.5 GHz resonator with a quality factor of 10$^4$. Working in the few photon limit indicates that the devices can be used to change the frequency of individual photons, this is however still to be demonstrated. As a part of this work the dressed states of a superconducting charge qubit was also studied.

•Jan 1, 2008•0 citations

Design, Simulation, and Experimental Validation of 3D Resonant Cavities for CryoCMOS and Superconducting Qubit Readout

Beatriz Sacramento, Ednilson Lopes, Francisco P. M. Rouxinol

Three-dimensional microwave cavities are key components for superconducting-qubit readout and for the characterization of cryogenic microwave electronics [1]. In this work, we report the design, simulation, fabrication, and experimental validation of a rectangular 3D resonant cavity targeting operation near 5.4 GHz, compatible with the frequency range of CryoCMOS voltage-controlled oscillators (VCO). The cavity dimensions were obtained from analytical mode calculations, corrected for practical machining constraints, and validated using finite-element electromagnetic simulations in ANSYS HFSS. A split-block aluminum cavity was fabricated and characterized at room temperature using vector network analysis. The measured resonances agree with analytical and simulated predictions within sub-1% deviation, confirming the accuracy of the design procedure. Different SMA connector penetration configurations were experimentally investigated to evaluate the trade-off between loaded quality factor and transmission efficiency. The asymmetric $7 \mathrm{~mm} / 8 \mathrm{~mm}$ configuration provided the best compromise, yielding a loaded quality factor of approximately 3200 and improving the transmitted signal by about 20 dB compared with the symmetric $\mathrm{7 ~ m m} / \mathrm{7 ~ m m}$ configuration. These results demonstrate a reproducible design route for 3D cavities intended for CryoCMOS testing and future superconducting-qubit readout experiments.

Symposium on Microelectronics Technology and Devices•Aug 1, 2026•0 citations
In the context of engineered quantum systems, there is a demand for superconducting tunable devices, able to operate with high-quality factors at power levels equivalent to only a few photons. In this work, we developed a 3D microwave re-entrant cavity with such characteristics ready to provide a very fine-tuning of a high-Q resonant mode over a large dynamic range. This system has an electronic tuning mechanism based on a mechanically amplified piezoelectric actuator, which controls the resonator dominant mode frequency by changing the cavity narrow gap by very small displacements. Experiments were conducted at room and dilution refrigerator temperatures showing a large dynamic range up to 4 GHz and 1 GHz, respectively, and were compared to a finite element method model simulated data. At elevated microwave power input, nonlinear thermal effects were observed to destroy the superconductivity of the cavity due to the large electric fields generated in the small gap of the re-entrant cavity.
Frequency tunability of three dimensional (3D) microwave cavities opens up numerous possibilities for their use in hybrid quantum systems and related technologies. For many applications, it is desirable to tune the resonance at cryogenic temperatures without mechanical actuation. We show that a superconducting 3D microwave cavity can be tuned at the percent level by taking advantage of the dielectric properties of superfluid 4He at millikelvin temperatures, without affecting its intrinsic quality factor—reaching 3 × 105 in the present experiment.
A wide variety of applications of microwave cavities, such as measurement and control of superconducting qubits, magnonic resonators, and phase noise filters, would be well served by having a highly tunable microwave resonance. Often this tunability is desired in situ at low temperatures, where one can take advantage of superconducting cavities. To date, such cryogenic tuning while maintaining a high quality factor has been limited to ∼500 MHz. Here we demonstrate a three-dimensional superconducting microwave cavity that shares one wall with a pressurized volume of helium. Upon pressurization of the helium chamber, the microwave cavity is deformed, which results in in situ tuning of its resonant frequency by more than 5 GHz, greater than 60% of the original 8 GHz resonant frequency. The quality factor of the cavity remains approximately constant at ≈7 × 103 over the entire range of tuning. As a demonstration of its usefulness, we implement a tunable cryogenic phase noise filter, which reduces the phase noise of our source by approximately 10 dB above 400 kHz.
This thesis describes the design, fabrication, and characterization of 3D superconducting microwave cavities for two applications. It first describes a cryogenically compatible microwave filter that is able to tune its resonant frequency by an unprecedented 5 GHz via deformation caused by a a helium pressure vessel. Then, it describes a novel microwave optomechanics device where such a cavity is coupled to an aluminized SiN membrane. It demonstrates that this device can be back-action cooled from the 450 mK base temperature of the cryostat down to 160 mK.
Abstract Superconducting microwave circuits show great potential for practical quantum technological applications such as quantum information processing. However, fast and on-demand initialization of the quantum degrees of freedom in these devices remains a challenge. Here, we experimentally implement a tunable heat sink that is potentially suitable for the initialization of superconducting qubits. Our device consists of two coupled resonators. The first resonator has a high quality factor and a fixed frequency whereas the second resonator is designed to have a low quality factor and a tunable resonance frequency. We engineer the low quality factor using an on-chip resistor and the frequency tunability using a superconducting quantum interference device. When the two resonators are in resonance, the photons in the high-quality resonator can be efficiently dissipated. We show that the corresponding loaded quality factor can be tuned from above 105 down to a few thousand at 10 GHz in good quantitative agreement with our theoretical model.
In this licentiate thesis design, fabrication, and measurements of tunable superconducting microwave transmission line resonators are described. The resonators are of quarter wavelength type were the tuning is achieved by changing one of the boundary conditions of the resonator through a tunable impedance. As tunable impedance the Josephson inductance in form of SQUIDs is used. The Josephson inductance can then be tuned by applying a magnetic field to the SQUID loop. A tuning range of 750 MHz for a 5 GHz resonator is achieved, and as a figure of merit it can be tuned over 200 line widths. The purpose of the tunable resonators is to use them for dynamic coupling of superconducting quantum bits, this requires that the resonators can be tuned fast on the timescale of the resonator-qubit coupling. To measure tuning speeds faster then the ring up time of the resonators a method that measures the leakage of energy out of a detuned resonator was developed. With this method a frequency shift of the energy stored in the resonator can be measured. A detuning of 330 MHz in less than 10 ns is demonstrated for a 4.5 GHz resonator with a quality factor of 104^44. Working in the few photon limit indicates that the devices can be used to change the frequency of individual photons, this is however still to be demonstrated. As a part of this work the dressed states of a superconducting charge qubit was also studied.
Three-dimensional microwave cavities are key components for superconducting-qubit readout and for the characterization of cryogenic microwave electronics [1]. In this work, we report the design, simulation, fabrication, and experimental validation of a rectangular 3D resonant cavity targeting operation near 5.4 GHz, compatible with the frequency range of CryoCMOS voltage-controlled oscillators (VCO). The cavity dimensions were obtained from analytical mode calculations, corrected for practical machining constraints, and validated using finite-element electromagnetic simulations in ANSYS HFSS. A split-block aluminum cavity was fabricated and characterized at room temperature using vector network analysis. The measured resonances agree with analytical and simulated predictions within sub-1% deviation, confirming the accuracy of the design procedure. Different SMA connector penetration configurations were experimentally investigated to evaluate the trade-off between loaded quality factor and transmission efficiency. The asymmetric 7 mm/8 mm7 \mathrm{~mm} / 8 \mathrm{~mm}7 mm/8 mm configuration provided the best compromise, yielding a loaded quality factor of approximately 3200 and improving the transmitted signal by about 20 dB compared with the symmetric 7 mm/7 mm\mathrm{7 ~ m m} / \mathrm{7 ~ m m}7 mm/7 mm configuration. These results demonstrate a reproducible design route for 3D cavities intended for CryoCMOS testing and future superconducting-qubit readout experiments.