Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Next generation superconducting nanowire single-photon detectors

Kleanthis Erotokritou

Published Jan 1, 2019• 0 citations
Publisher

Abstract

Single photon detection advanced rapidly in the last decade. The superconducting nanowire single-photon detector (SNSPD) is an emerging technology, which offers low dark count rates, broadband sensitivity from visible to mid-infrared wavelengths and very high quantum efficiency. All these features are appealing for future emerging applications in remote gas sensing, quantum key distribution and quantum information processing. By enclosing the detector in an optical cavity, tuned to the operating wavelength, the total system detection of the SNSPD is improved. Based on the cavity design, the detector absorption is boosted at the desired experimental wavelength. Devices have been fabricated and tested, in this thesis, with enhanced detection efficiency at near-infrared, infrared and mid-infrared wavelengths. NbTiN detectors fabricated on Ta2O5 / SiO2 distributed Bragg reflectors (DBR) for front-side coupling exhibit a system detection efficiency of ≈ 90% at λ = 940 nm for the best device measured. SNSPDs were also fabricated in NbTiN on metallic mirrors for back-side coupling for 1550 and 2333 nm experimental wavelengths. The first design exhibited a system detection efficiency of ≈ 84.5%, at λ = 1550 nm for the best device measured. The second exhibited low system detection efficiency since the device suffered from unexpectedly high dark count rate mainly due to blackbody radiation at 2.2 K. However, it was possible to measure the timing jitter of this device at 350 mK indicating a FWHM of 84 ps. Another technique to improve the total system detection efficiency of the SNSPD, is by fabricating a hairpin-shaped nanowire atop a single mode waveguide. In this design, photons travel through the waveguide and via evanescent coupling are absorbed in the nanowire. These SNSPD devices have been designed to thread along single mode Si ridge waveguides using a hairpin-shaped nanowire structure, which offers enhanced coupling and absorption efficiency via evanescent coupling. These ultra-thin superconducting MoSi detectors are precisely patterned on top of a single mode Si waveguide (600 nm) with alignment error less than 40 nm. Low temperature electrical and nano-optical characterization was carried out using a two-stage pulse tube (PT) coldhead, using an additional 4He / 3He sorption pump, low vibration characterization of SNSPD devices at 350 mK was carried out. Characterised devices exhibit low dark count rate <5 counts per second and timing jitter of ≈ 83 ps full width half maximum (FWHM) at wavelength (λ) = 1550 nm and at critical current ≈ 30 µA.

DOI
10.5525/gla.thesis.41108

Related papers

Superconducting single photon detectors for quantum information processing

Robert A. Kirkwood

Single photon detectors are a vital part of many emerging technologies which harness the quantum properties of light to benefit the fields of communication, computation and sensing. Superconducting nanowire single photon detectors (SNSPDs) offer high detection efficiency, low dark count rates, low timing jitter, and infrared sensitivity that are required by the most demanding single photon counting applications. This thesis presents SNSPDs fabricated and tested at the University of Glasgow that are integrated with optical structures which enable enhanced detection efficiency and integration with waveguide circuit technology. The monolithic integration of waveguide circuit components presents a route towards realisation of an optical quantum information processor that has the stability and scalability to perform the demanding tasks of quantum computation. A novel process is introduced for incorporating superconducting detectors with single mode gallium arsenide waveguides and quantum dot single photon sources. Together these elements would enable the generation of quantum states of light which could be manipulated and detected on a single chip. Detectors are patterned in NbTiN thin superconducting films on to suspended nanobeam waveguides with better than 50 nm alignment accuracy. Low temperature electrical and optical testing confirms the detectors’ single photon sensitivity under direct illumination as well as to waveguide coupled light. Measured detectors were found to have internal registering efficiencies of 6.8 ± 2.4%. Enhancing absorption of photons into thin superconducting films is vital to the creation of high efficiency superconducting single photon detectors. Fabricating an SNSPD on a dielectric mirror creates a partial cavity that can be tailored to enhance detection of light at specific wavelengths. Devices have been fabricated and tested in this thesis with enhanced detection efficiency at infrared and visible wavelengths for quantum cryptography, remote sensing and life science applications. Detectors fabricated in NbTiN on GaAs/AlGaAs Bragg mirrors exhibited a system detection efficiency of 1.5% at 1500 nm wavelength for the best device measured. SNSPDs were also fabricated in NbN on aperiodic dielectric mirrors with a range of different bandwidths. A peak system detection efficiency of 82.7% at 808 nm wavelength was recorded.

•Jan 1, 2017•1 citation

Micro-fiber coupled superconducting nanowire single photon detector (Conference Presentation)

Lixing You

Ever since superconducting nanowire single-photon detectors (SNSPDs or SSPDs) were demonstrated, they have attracted a considerable attention due to the detectors’ promising performance that includes high detection efficiency (DE), low dark count rate (DCR), broadband sensitivity, and low timing jitter. The system detection efficiency (SDE) has been improved to be over 90% with a wavelength of 1550 nm in a fiber-coupled system by embedding the SNSPD in optical cavities. However, the implementation of optical cavity usually reduces the bandwidth of SNSPDs. As a result, there are some recent works on increasing the bandwidth of SNSPD. Furthermore, the size of the active area of meandered nanowires has to be compatible with the core size of an optical fiber such that good optical coupling can be achieved; this setup requires a long nanowire with a large kinetic inductance, thus resulting in a small counting rate and a large timing jitter, particularly for multi-mode fiber-coupled devices. Nevertheless, a particularly impressive waveguide-coupled SNSPD has been developed in recent years. By placing an SNSPD atop an optical waveguide that has been fabricated on various substrate materials, photons propagating in the waveguide have been found to be evanescently absorbed by nanowires that are only a few tens of microns long. The on-chip DE of this device has been estimated to be over 90%, thus indicating that it has both high absorptance and high intrinsic DE. If the waveguide and the nanowire are correctly dimensioned, the absorptance of this device can reach over 90% for a wavelength range of more than 700 nm. Furthermore, the length of the nanowire is shorter than that of the fiber-coupled SNSPD, thus leading to a higher count rate and lower timing jitter (~18 ps). However, unsatisfactory coupling losses between the optical fiber and the waveguide in such devices can decrease its SDE (~10%), thus limiting its applicability to quantum photonic integrated circuits (QPIC). Recently, we proposed a type of SNSPD that was coupled with microfibers (MFs), and simulations for this SNSPD indicated that its absorption would be as high as 90%. Microfibers and nanofibers, tapered adiabatically from standard fibers, with diameters close to or smaller than the wavelength of the guided light were demonstrated to have low transmittance losses by Tong et al. in 2003. MFs have been shown to have many interesting properties, such as strong evanescent fields, tight optical confinement, wideband abilities, and small masses; these properties are appealing for applications such as optical sensing and coupling. MFs also provide seamless connections with high transmittance from standard fibers; therefore, MF-coupled SNSPDs can achieve both high SDEs and wideband compatibility. We proposed and demonstrated the MF-coupled SNSPDs successfully. The simulation results indicate that with optimal device structure, the optical absorption with efficiency < 90% can be realized over a wavelength range of 350 nm to 2150 nm. The fabricated MF-coupled SNSPD, shows unparalleled broadband system detection efficiencies (SDEs) of more than 50% from 630 nm to 1500 nm. The SDEs reach 66% at 785 nm and 45% at 1550 nm. These results pave the way for ultra-broadband weak light detection with quantum-limit sensitivity.

Advanced Photon Counting Techniques•May 1, 2020•0 citations

Development of practical superconducting nanowire single photon detector system with high detection efficiency

Shigehito Miki, Taro Yamashita, Hirotaka Terai +3 more

We have developed a practical superconducting nanowire single photon detector (SNSPD) system with our superconducting thin films and devices fabrication, optical coupling packaging, and cryogenic technology. The SNSPD devices were fabricated from high-quality niobium nitride (NbN) ultra-thin films that were epitaxially grown on single-crystal MgO substrates, and optical cavity structure were applied for improvement of photo absorption efficiency. The SNSPD system was developed based on a compact Gifford-McMahon (GM) cryocooler, in which SNSPD can operate continuously at temperature of 2.9 K +/- 10 mK with low power consumption without any liquid cryogens. The system detection efficiencies at 1550 nm wavelength (at a 100 Hz dark count rate) were found to be 2.6% for device without optical cavity and 21% for device with optical cavity. The response speed of devices showed maximally 200 MHz with 5 × 5 mm square device, and timing jitter of 100 ps full width at a half maximum (FWHM) was observed.

IEEE International Conference on Space Optical Systems and Applications (ICSOS)•May 1, 2011•0 citations

Nano-optical measurements of novel superconducting single photon detector designs

Robert M. Heath, Michael G. Tanner, L. San Emeterio Alvarez +4 more

Superconducting nanowire single photon detectors (SNSPDs) are a highly promising emerging photon counting technology, offering infrared sensitivity combined with low dark count rates and sub-100 ps timing jitter [1]. These devices are under consideration for a wide variety of photon counting applications, from quantum cryptography to remote sensing. Next generation device designs based on optical cavities, ultra narrow wires, parallel wire arrays and nano-antenna enhanced devices are being evaluated to meet the demands of advanced photon counting applications.

Conference on Lasers and Electro-Optics Europe & European Quantum Electronics Conference (CLEO/Europe-EQEC)•May 1, 2013•0 citations

Emerging materials for superconducting nanowire photon counting arrays

Umberto Nasti

Superconducting nanowire single-photon detectors (SNSPDs) are the leading technology for low noise, high efficiency infrared single-photon detection. The basic SNSPD consists of a nanowire patterned in an ultrathin superconducting thin film, which is cooled below its critical temperature and biased close to its critical current. The absorption of a single-photon creates a resistive region, triggering a fast output voltage pulse which can be readily amplified and registered. The excellent performance of SNSPDs at near-infrared and telecommunications wavelengths has led to their adoption in important applications such as quantum secure communications, single-photon spectroscopy and single-photon LIDAR. A clear challenge for the SNSPD community is to extend the spectral range of SNSPDs into the mid infrared, and to improve material uniformity to enable the realization of large area arrays for multimode or free space coupling. The aim of this work is to evaluate potential materials for next generation mid-infrared SNSPD arrays. In this work, thin films of polycrystalline NbN and amorphous MoSi have been optimized to test the uniformity of a multipixel array configuration composed of 8 nanowire meander structures covering 10 um x 10 um area, 100 nm width and 50% filling factor. The 8-pixels SNSPD arrays have been patterned on 8 nm thickness NbN grown on high resistivity silicon (HR Si) substrate at room temperature and at 800 °C exhibiting respectively 4.4 K and 7.3 K as mean critical temperature across the pixels. The 8- pixels SNSPD array patterned on 8 nm thickness MoSi cooling the HR Si substrate to -180 °C has exhibited a mean critical temperature of 3.2 K across the pixels. Optical properties have been measured by an attenuated 1550 nm laser diode source delivered by single mode optical fibre at a controlled distance from the chip in order to broadly illuminate the array. The optical properties have been studied only for the 8 nm thickness NbN SNSPD array grown at room temperature has demonstrated uniform optical properties across pixels exhibiting similar saturation of the internal efficiency over a large bias, similar dark count rate and similar timing jitter (about 137 ps) across pixels. In the single photon regime at 1550 nm, pixels 4 and 6 of the 8 nm thickness NbN SNSPD array exhibit 28.4% and 4.7% pixel detection efficiency as measured at the bias current 95% of their respective critical current at 2.2 K.

•Jan 1, 2020•0 citations

Enhanced telecom wavelength single-photon detection with NbTiN superconducting nanowires on oxidized silicon

Michael G. Tanner, Chandra M. Natarajan, V. K. Pottapenjara +10 more

Superconducting nanowire single-photon detectors (SNSPDs) have emerged as a highly promising infrared single-photon detector technology. Next-generation devices are being developed with enhanced detection efficiency (DE) at key technological wavelengths via the use of optical cavities. Furthermore, new materials and substrates are being explored for improved fabrication versatility, higher DE, and lower dark counts. We report on the practical performance of packaged NbTiN SNSPDs fabricated on oxidized silicon substrates in the wavelength range from 830 to 1700 nm. We exploit constructive interference from the SiO2/Si interface in order to achieve enhanced front-side fiber-coupled DE of 23.2 % at 1310 nm, at 1 kHz dark count rate, with 60 ps full width half maximum timing jitter.

Applied Physics Letters•May 31, 2010•112 citations
Single photon detection advanced rapidly in the last decade. The superconducting nanowire single-photon detector (SNSPD) is an emerging technology, which offers low dark count rates, broadband sensitivity from visible to mid-infrared wavelengths and very high quantum efficiency. All these features are appealing for future emerging applications in remote gas sensing, quantum key distribution and quantum information processing. By enclosing the detector in an optical cavity, tuned to the operating wavelength, the total system detection of the SNSPD is improved. Based on the cavity design, the detector absorption is boosted at the desired experimental wavelength. Devices have been fabricated and tested, in this thesis, with enhanced detection efficiency at near-infrared, infrared and mid-infrared wavelengths. NbTiN detectors fabricated on Ta2O5 / SiO2 distributed Bragg reflectors (DBR) for front-side coupling exhibit a system detection efficiency of ≈ 90% at λ = 940 nm for the best device measured. SNSPDs were also fabricated in NbTiN on metallic mirrors for back-side coupling for 1550 and 2333 nm experimental wavelengths. The first design exhibited a system detection efficiency of ≈ 84.5%, at λ = 1550 nm for the best device measured. The second exhibited low system detection efficiency since the device suffered from unexpectedly high dark count rate mainly due to blackbody radiation at 2.2 K. However, it was possible to measure the timing jitter of this device at 350 mK indicating a FWHM of 84 ps. Another technique to improve the total system detection efficiency of the SNSPD, is by fabricating a hairpin-shaped nanowire atop a single mode waveguide. In this design, photons travel through the waveguide and via evanescent coupling are absorbed in the nanowire. These SNSPD devices have been designed to thread along single mode Si ridge waveguides using a hairpin-shaped nanowire structure, which offers enhanced coupling and absorption efficiency via evanescent coupling. These ultra-thin superconducting MoSi detectors are precisely patterned on top of a single mode Si waveguide (600 nm) with alignment error less than 40 nm. Low temperature electrical and nano-optical characterization was carried out using a two-stage pulse tube (PT) coldhead, using an additional 4He / 3He sorption pump, low vibration characterization of SNSPD devices at 350 mK was carried out. Characterised devices exhibit low dark count rate <5 counts per second and timing jitter of ≈ 83 ps full width half maximum (FWHM) at wavelength (λ) = 1550 nm and at critical current ≈ 30 µA.
Single photon detectors are a vital part of many emerging technologies which harness the quantum properties of light to benefit the fields of communication, computation and sensing. Superconducting nanowire single photon detectors (SNSPDs) offer high detection efficiency, low dark count rates, low timing jitter, and infrared sensitivity that are required by the most demanding single photon counting applications. This thesis presents SNSPDs fabricated and tested at the University of Glasgow that are integrated with optical structures which enable enhanced detection efficiency and integration with waveguide circuit technology. The monolithic integration of waveguide circuit components presents a route towards realisation of an optical quantum information processor that has the stability and scalability to perform the demanding tasks of quantum computation. A novel process is introduced for incorporating superconducting detectors with single mode gallium arsenide waveguides and quantum dot single photon sources. Together these elements would enable the generation of quantum states of light which could be manipulated and detected on a single chip. Detectors are patterned in NbTiN thin superconducting films on to suspended nanobeam waveguides with better than 50 nm alignment accuracy. Low temperature electrical and optical testing confirms the detectors’ single photon sensitivity under direct illumination as well as to waveguide coupled light. Measured detectors were found to have internal registering efficiencies of 6.8 ± 2.4%. Enhancing absorption of photons into thin superconducting films is vital to the creation of high efficiency superconducting single photon detectors. Fabricating an SNSPD on a dielectric mirror creates a partial cavity that can be tailored to enhance detection of light at specific wavelengths. Devices have been fabricated and tested in this thesis with enhanced detection efficiency at infrared and visible wavelengths for quantum cryptography, remote sensing and life science applications. Detectors fabricated in NbTiN on GaAs/AlGaAs Bragg mirrors exhibited a system detection efficiency of 1.5% at 1500 nm wavelength for the best device measured. SNSPDs were also fabricated in NbN on aperiodic dielectric mirrors with a range of different bandwidths. A peak system detection efficiency of 82.7% at 808 nm wavelength was recorded.
Ever since superconducting nanowire single-photon detectors (SNSPDs or SSPDs) were demonstrated, they have attracted a considerable attention due to the detectors’ promising performance that includes high detection efficiency (DE), low dark count rate (DCR), broadband sensitivity, and low timing jitter. The system detection efficiency (SDE) has been improved to be over 90% with a wavelength of 1550 nm in a fiber-coupled system by embedding the SNSPD in optical cavities. However, the implementation of optical cavity usually reduces the bandwidth of SNSPDs. As a result, there are some recent works on increasing the bandwidth of SNSPD. Furthermore, the size of the active area of meandered nanowires has to be compatible with the core size of an optical fiber such that good optical coupling can be achieved; this setup requires a long nanowire with a large kinetic inductance, thus resulting in a small counting rate and a large timing jitter, particularly for multi-mode fiber-coupled devices. Nevertheless, a particularly impressive waveguide-coupled SNSPD has been developed in recent years. By placing an SNSPD atop an optical waveguide that has been fabricated on various substrate materials, photons propagating in the waveguide have been found to be evanescently absorbed by nanowires that are only a few tens of microns long. The on-chip DE of this device has been estimated to be over 90%, thus indicating that it has both high absorptance and high intrinsic DE. If the waveguide and the nanowire are correctly dimensioned, the absorptance of this device can reach over 90% for a wavelength range of more than 700 nm. Furthermore, the length of the nanowire is shorter than that of the fiber-coupled SNSPD, thus leading to a higher count rate and lower timing jitter (~18 ps). However, unsatisfactory coupling losses between the optical fiber and the waveguide in such devices can decrease its SDE (~10%), thus limiting its applicability to quantum photonic integrated circuits (QPIC). Recently, we proposed a type of SNSPD that was coupled with microfibers (MFs), and simulations for this SNSPD indicated that its absorption would be as high as 90%. Microfibers and nanofibers, tapered adiabatically from standard fibers, with diameters close to or smaller than the wavelength of the guided light were demonstrated to have low transmittance losses by Tong et al. in 2003. MFs have been shown to have many interesting properties, such as strong evanescent fields, tight optical confinement, wideband abilities, and small masses; these properties are appealing for applications such as optical sensing and coupling. MFs also provide seamless connections with high transmittance from standard fibers; therefore, MF-coupled SNSPDs can achieve both high SDEs and wideband compatibility. We proposed and demonstrated the MF-coupled SNSPDs successfully. The simulation results indicate that with optimal device structure, the optical absorption with efficiency < 90% can be realized over a wavelength range of 350 nm to 2150 nm. The fabricated MF-coupled SNSPD, shows unparalleled broadband system detection efficiencies (SDEs) of more than 50% from 630 nm to 1500 nm. The SDEs reach 66% at 785 nm and 45% at 1550 nm. These results pave the way for ultra-broadband weak light detection with quantum-limit sensitivity.
We have developed a practical superconducting nanowire single photon detector (SNSPD) system with our superconducting thin films and devices fabrication, optical coupling packaging, and cryogenic technology. The SNSPD devices were fabricated from high-quality niobium nitride (NbN) ultra-thin films that were epitaxially grown on single-crystal MgO substrates, and optical cavity structure were applied for improvement of photo absorption efficiency. The SNSPD system was developed based on a compact Gifford-McMahon (GM) cryocooler, in which SNSPD can operate continuously at temperature of 2.9 K +/- 10 mK with low power consumption without any liquid cryogens. The system detection efficiencies at 1550 nm wavelength (at a 100 Hz dark count rate) were found to be 2.6% for device without optical cavity and 21% for device with optical cavity. The response speed of devices showed maximally 200 MHz with 5 × 5 mm square device, and timing jitter of 100 ps full width at a half maximum (FWHM) was observed.
Superconducting nanowire single photon detectors (SNSPDs) are a highly promising emerging photon counting technology, offering infrared sensitivity combined with low dark count rates and sub-100 ps timing jitter [1]. These devices are under consideration for a wide variety of photon counting applications, from quantum cryptography to remote sensing. Next generation device designs based on optical cavities, ultra narrow wires, parallel wire arrays and nano-antenna enhanced devices are being evaluated to meet the demands of advanced photon counting applications.
Superconducting nanowire single-photon detectors (SNSPDs) are the leading technology for low noise, high efficiency infrared single-photon detection. The basic SNSPD consists of a nanowire patterned in an ultrathin superconducting thin film, which is cooled below its critical temperature and biased close to its critical current. The absorption of a single-photon creates a resistive region, triggering a fast output voltage pulse which can be readily amplified and registered. The excellent performance of SNSPDs at near-infrared and telecommunications wavelengths has led to their adoption in important applications such as quantum secure communications, single-photon spectroscopy and single-photon LIDAR. A clear challenge for the SNSPD community is to extend the spectral range of SNSPDs into the mid infrared, and to improve material uniformity to enable the realization of large area arrays for multimode or free space coupling. The aim of this work is to evaluate potential materials for next generation mid-infrared SNSPD arrays. In this work, thin films of polycrystalline NbN and amorphous MoSi have been optimized to test the uniformity of a multipixel array configuration composed of 8 nanowire meander structures covering 10 um x 10 um area, 100 nm width and 50% filling factor. The 8-pixels SNSPD arrays have been patterned on 8 nm thickness NbN grown on high resistivity silicon (HR Si) substrate at room temperature and at 800 °C exhibiting respectively 4.4 K and 7.3 K as mean critical temperature across the pixels. The 8- pixels SNSPD array patterned on 8 nm thickness MoSi cooling the HR Si substrate to -180 °C has exhibited a mean critical temperature of 3.2 K across the pixels. Optical properties have been measured by an attenuated 1550 nm laser diode source delivered by single mode optical fibre at a controlled distance from the chip in order to broadly illuminate the array. The optical properties have been studied only for the 8 nm thickness NbN SNSPD array grown at room temperature has demonstrated uniform optical properties across pixels exhibiting similar saturation of the internal efficiency over a large bias, similar dark count rate and similar timing jitter (about 137 ps) across pixels. In the single photon regime at 1550 nm, pixels 4 and 6 of the 8 nm thickness NbN SNSPD array exhibit 28.4% and 4.7% pixel detection efficiency as measured at the bias current 95% of their respective critical current at 2.2 K.
Superconducting nanowire single-photon detectors (SNSPDs) have emerged as a highly promising infrared single-photon detector technology. Next-generation devices are being developed with enhanced detection efficiency (DE) at key technological wavelengths via the use of optical cavities. Furthermore, new materials and substrates are being explored for improved fabrication versatility, higher DE, and lower dark counts. We report on the practical performance of packaged NbTiN SNSPDs fabricated on oxidized silicon substrates in the wavelength range from 830 to 1700 nm. We exploit constructive interference from the SiO2/Si interface in order to achieve enhanced front-side fiber-coupled DE of 23.2 % at 1310 nm, at 1 kHz dark count rate, with 60 ps full width half maximum timing jitter.