Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1105.1956 · Superconductor Science and Technology

Balanced superconductor–insulator–superconductor mixer on a 9 µm silicon membrane

M. Westig, K Jacobs, J Stutzki, M Schultz, M Justen, C E Honingh

Published Jul 1, 2011• 30 citations
arXivHTMLPDF

Abstract

We present a 380-520 GHz balanced superconductor-insulator-superconductor (SIS) mixer on a single silicon substrate. All radio-frequency (RF) circuit components are fabricated on a $9 μ$m thick membrane. The intermediate frequency (IF) is separately amplified and combined. The balanced mixer chip, using Nb/Al/Al$_{2}$O$_{3}$/Nb SIS junctions, is mounted in a tellurium copper waveguide block at 4.2 K using Au beam lead contacts. We find uncorrected minimum receiver double-sideband noise temperatures of 70 K and a noise suppression of up to 18 dB, measured within a 440-495 GHz RF and a 4-8 GHz IF bandwidth, representing state-of-the-art device performance.

DOI
10.1088/0953-2048/24/8/085012

Related papers

Low-noise integrated balanced SIS mixer for 787–950 GHz

Yasunori Fujii, Takafumi Kojima, Álvaro González +5 more

Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.

Superconductor Science and Technology•Nov 30, 2016•13 citations

A Low-noise Balanced SIS Mixer for the 790-950 GHz Band

Takafumi Kojima, Yasunori FUJII, Yoshinori Uzawa

We have developed a low-noise balanced superconductor-insulator-superconductor (SIS) mixer using a waveguide 3-dB 90-degree hybrid coupler over the radio frequency (RF) range of 790-950 GHz and intermediate frequency range of 4-12 GHz at an operating temperature of 4 K. The RF coupler was carefully designed in regards to machining errors so that the entire amplitude imbalance including the mixer gain became smaller. The fabricated coupler was characterized at both room and cryogenic temperature. The receiver noise temperature of the balanced SIS mixer was below 350 K over the entire frequency band and the local oscillator (LO) noise rejection ratio was estimated to be more than 15 dB. This result is equivalent to state-ofthe-art mixer performance at this frequency range.

TEION KOGAKU (Journal of Cryogenics and Superconductivity Society of Japan)•Jan 1, 2014•2 citations

An SIS Mixer With 2hf/k DSB Noise Temperature at 163 - 211 GHz Band

Bhushan Billade, Alexey Pavolotsky, Victor Y. Belitsky

We present the design and the performance of a fixed-tuned, all niobium (Nb) Superconductor-Insulator-Superconductor (SIS) mixer covering RF frequencies from 163 to 211 GHz with 4-8 GHz IF bandwidth. The mixer uses two Nb/Al-AlOx/Nb junctions of size 3 μm2each with theRnAproduct of 30 Ω·μm2, in a twin junction configuration. An local oscillator (LO) directional coupler made of superconducting lines with slots in the ground plane is integrated on the SIS mixer chip. The isolated port of the LO coupler is terminated using a wide-band resistive load with a sheet resistance of 12 Ω/□. The SIS tuning circuitry is optimized to achieve best power match between the twin junctions and the embedding circuitry. The measurement of the double sideband mixer noise at 171 GHz shows that the receiver noise temperature is approximately 17 K, which is just 2hf/k. The estimated noise contribution from the RF loss and the IF chain at 176 GHz LO frequency is 8 K and 7.5 K respectively, resulting in a SIS mixer noise ofhf/2k. The mixer noise performance across the entire RF band varies between 19 to 25 K. This is to our knowledge the best reported noise temperature at these frequencies till now.

IEEE Transactions on Terahertz Science and Technology•May 2, 2013•21 citations

Waveguide-Type SIS Receiver Using All-NbN Technique

M. TAKEDA

This paper describes the first experimental results for a waveguide-type all-NbN superconductor-insulator-superconductor (SIS) heterodyne mixer on an MgO substrate designed to operate over the gap frequency of Nb. The mixer consists of an NbN/MgO/NbN junction, which has a length of one wavelength at 880GHz as a tuning circuit, an NbN/MgO/NbN microstrip as a λ/4 impedance transformer, and an RF choke filter. The mixer chip was designed using a high-frequency-structure simulator. Its return-loss and embedding-impedance characteristics were examined using a 180-times-scaled mixer model. By optimizing the cutting and polishing processes for the MgO substrate, we were able to fabricate the mixer chip with an accuracy of less than 5 μm. We succeeded in mounting the chip on a mixer block and in estimating the receiver noise temperature. The uncorrected minimum double-sideband receiver noise temperature was 740 K at 824 GHz. A comparison of the receiver noise temperature in a quasi-optical SIS mixer fabricated on the same wafer as the waveguide mixer showed that input noise was the major contributor to receiver noise in the waveguide mixer.

IEICE Transactions on Electronics•Feb 1, 2006•5 citations

A 0.5 THz Sideband Separation SIS Mixer for APEX Telescope

Raquel Rodriguez Monje, Victor Y. Belitsky, Vessen Vassilev +6 more

Abstract — We present the design and the experimental results of a fixed-tuned sideband-separating superconductor-insulator-superconductor (SIS) mixer for 385- 500 GHz. The sideband separation is achieved using a quadrature scheme, where two separate DSB mixer blocks are combined with an intermediate waveguide component containing the LO waveguide distribution circuitry and RF waveguide hybrid. The intermediate waveguide piece is fabricated by using copper micromachining, which gives dimensions ’ accuracy better than 1 μm. The RF signal coming from the waveguide hybrid is coupled to the SIS junctions through an E-probe with integrated bias-T. We implemented an on-chip LO injection solution, where the LO coupler is integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO coupler is made as a combination of superconducting microstrip lines and slot-lines (branches), which gives almost a lossless solution. With the fabrication accuracy better than 0.5 μm by using optical lithography, the circuitry is proven to give a good performance following the simulations expectations. I.

•Apr 1, 2008•4 citations

Development of Integrated Superconducting Balanced Mixers for THz Focal Plane Arrays

Sina Fathi

This thesis work covers the development of integrated superconducting balanced mixers for heterodyne (resolution> 10^7) THz focal plane arrays. The aim was to develop on chip integrated balanced superconductor-insulator-superconductor (SIS) mixers at 800-1100 GHz and in addition at the Intermediate Frequency (IF) 4-12 GHz integrated \n180° IF hybrids both for the CHAI (CCAT Heterodyne Array Instrument) receiver for the Cerro Chajnantor Atacama Telescope (CCAT) observatory. A planar 180º hybrid ring \ncoupler, two separate slotline antennas, two separate slotline to CPW transitions to employ for the 800-1100 GHz balanced SIS mixer, based on NbTiN circuitry, were designed and all were integrated on one 6 μm silicon substrate. \nAt the IF side of the integrated balanced mixers, two different configurations of superconducting \nintegrated 180º IF hybrids were designed to combine the two generated IF outputs at either Σ or Δ port depending on the choice of the input port of the hybrid. These 4-12 GHz IF hybrid coupler designs were based on planar lumped elements to miniaturize the size to about 0.5×2.2 μm^2. The designs were simulated for 500 μm and 9 μm silicon substrates. The latter is studied in order to integrate it at a later \nstage with the RF part of the mixer on one substrate. The lithography mask and subsequently the micro-fabrication of the IF hybrids were made. The measurement of the Nb based IF hybrid on a 500 μm silicon with Vector Network Analyzer (VNA) in liquid helium is reported. The measured results are analyzed and compared to the IF hybrid with the implemented superconducting Nb in the simulation. \n \nThese developments and designs will be available and applicable for future receivers of the CCAT-prime observatory. Because the original envisioned CCAT-observatory project was discontinued due to the lack of funding, it was decided that my 800-1100 GHz designs would not be further developed into working mixers for the time being and that other projects would get priority. \n \nMy work continued with the the development of integrated 1.9 THz balanced Hot Electron Bolometer (HEB) mixers. This development is relevant for 1.9 THz focal plane array receivers for the airborne Stratospheric Observatory for the Far Infrared (SOFIA), for which the mixers are developed in our group. The LO power consumption of the array presently limits its usable RF bandwidth. This power consumption could be reduced by a factor of 5 by using integrated balanced mixers. The mixers are based on superconducting NbN HEBs and Au is applied as normal metal to wire the mixers. The development contained design, micro-nanofabrication, DC and cryogenic high frequency measurements. All designed planar elements consisted of an 1 octave broadband 180º RF hybrid-ring coupler, two slotline tapered antennas, two slotline to \nCPW transitions, two or four 120 Ω HEB bridges, two low pass filters (LPFs) and two DC/IF blocking capacitors integrated on one 3 μm silicon substrate and simulated using CST suite. A further integrated 1.9 THz HEB mixer was designed to support the two separate IF outputs at one side of a 3 μm silicon substrate with employing a CPW-CPW crossover. \n \nThe micro-nanofabrication of the 1.9 THz balanced mixers was done in house using E-beam and photo-lithography techniques. Almost all DC measured devices contained HEB bridges that were sufficiently similar in normal state resistance and transition temperature. The average resistance of the devices, in the one available wafer for measurements, was about 17% too low. The transition temperature of the devices was around 7.9 K, in comparison to 8.5 K for our state of the art single pixel mixers. The two machined 1.9 THz balanced waveguide blocks for testing of the devices were machined in the institute's in house workshop. I have tested the transmission of the blocks, and thereby the workmanship, with a THz time Domain Spectrometer, showed about 2.4 dB of loss per mm waveguide length at room temperature, for a split block waveguide made of the oxygen free copper tellurium alloy (CuTe). \n \nThe cryogenic RF measurements showed a very similar LO-power coupling to both mixers in the balanced device, from both input ports of the mixer. By using an in house built Quantum Cascade Laser (QCL) LO as a local oscillator and a severely attenuated Virginia Diode multiplier chain (VDI) LO as a signal source I have shown proper balanced mixer behavior, thereby validating the design. Signal suppression up to 38 dB was shown by inverting the bias voltages on one of the mixers in the balanced device, which added a 180º phase change to the IF of one of the mixers.

•Nov 9, 2018•0 citations
We present a 380-520 GHz balanced superconductor-insulator-superconductor (SIS) mixer on a single silicon substrate. All radio-frequency (RF) circuit components are fabricated on a 9μ9 μ9μm thick membrane. The intermediate frequency (IF) is separately amplified and combined. The balanced mixer chip, using Nb/Al/Al2_{2}2​O3_{3}3​/Nb SIS junctions, is mounted in a tellurium copper waveguide block at 4.2 K using Au beam lead contacts. We find uncorrected minimum receiver double-sideband noise temperatures of 70 K and a noise suppression of up to 18 dB, measured within a 440-495 GHz RF and a 4-8 GHz IF bandwidth, representing state-of-the-art device performance.
Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.
We have developed a low-noise balanced superconductor-insulator-superconductor (SIS) mixer using a waveguide 3-dB 90-degree hybrid coupler over the radio frequency (RF) range of 790-950 GHz and intermediate frequency range of 4-12 GHz at an operating temperature of 4 K. The RF coupler was carefully designed in regards to machining errors so that the entire amplitude imbalance including the mixer gain became smaller. The fabricated coupler was characterized at both room and cryogenic temperature. The receiver noise temperature of the balanced SIS mixer was below 350 K over the entire frequency band and the local oscillator (LO) noise rejection ratio was estimated to be more than 15 dB. This result is equivalent to state-ofthe-art mixer performance at this frequency range.
We present the design and the performance of a fixed-tuned, all niobium (Nb) Superconductor-Insulator-Superconductor (SIS) mixer covering RF frequencies from 163 to 211 GHz with 4-8 GHz IF bandwidth. The mixer uses two Nb/Al-AlOx/Nb junctions of size 3 μm2each with theRnAproduct of 30 Ω·μm2, in a twin junction configuration. An local oscillator (LO) directional coupler made of superconducting lines with slots in the ground plane is integrated on the SIS mixer chip. The isolated port of the LO coupler is terminated using a wide-band resistive load with a sheet resistance of 12 Ω/□. The SIS tuning circuitry is optimized to achieve best power match between the twin junctions and the embedding circuitry. The measurement of the double sideband mixer noise at 171 GHz shows that the receiver noise temperature is approximately 17 K, which is just 2hf/k. The estimated noise contribution from the RF loss and the IF chain at 176 GHz LO frequency is 8 K and 7.5 K respectively, resulting in a SIS mixer noise ofhf/2k. The mixer noise performance across the entire RF band varies between 19 to 25 K. This is to our knowledge the best reported noise temperature at these frequencies till now.
This paper describes the first experimental results for a waveguide-type all-NbN superconductor-insulator-superconductor (SIS) heterodyne mixer on an MgO substrate designed to operate over the gap frequency of Nb. The mixer consists of an NbN/MgO/NbN junction, which has a length of one wavelength at 880GHz as a tuning circuit, an NbN/MgO/NbN microstrip as a λ/4 impedance transformer, and an RF choke filter. The mixer chip was designed using a high-frequency-structure simulator. Its return-loss and embedding-impedance characteristics were examined using a 180-times-scaled mixer model. By optimizing the cutting and polishing processes for the MgO substrate, we were able to fabricate the mixer chip with an accuracy of less than 5 μm. We succeeded in mounting the chip on a mixer block and in estimating the receiver noise temperature. The uncorrected minimum double-sideband receiver noise temperature was 740 K at 824 GHz. A comparison of the receiver noise temperature in a quasi-optical SIS mixer fabricated on the same wafer as the waveguide mixer showed that input noise was the major contributor to receiver noise in the waveguide mixer.
Abstract — We present the design and the experimental results of a fixed-tuned sideband-separating superconductor-insulator-superconductor (SIS) mixer for 385- 500 GHz. The sideband separation is achieved using a quadrature scheme, where two separate DSB mixer blocks are combined with an intermediate waveguide component containing the LO waveguide distribution circuitry and RF waveguide hybrid. The intermediate waveguide piece is fabricated by using copper micromachining, which gives dimensions ’ accuracy better than 1 μm. The RF signal coming from the waveguide hybrid is coupled to the SIS junctions through an E-probe with integrated bias-T. We implemented an on-chip LO injection solution, where the LO coupler is integrated onto the mixer chip and fabricated together with the SIS junction and the tuning circuitry. The on-chip LO coupler is made as a combination of superconducting microstrip lines and slot-lines (branches), which gives almost a lossless solution. With the fabrication accuracy better than 0.5 μm by using optical lithography, the circuitry is proven to give a good performance following the simulations expectations. I.
This thesis work covers the development of integrated superconducting balanced mixers for heterodyne (resolution> 10^7) THz focal plane arrays. The aim was to develop on chip integrated balanced superconductor-insulator-superconductor (SIS) mixers at 800-1100 GHz and in addition at the Intermediate Frequency (IF) 4-12 GHz integrated \n180° IF hybrids both for the CHAI (CCAT Heterodyne Array Instrument) receiver for the Cerro Chajnantor Atacama Telescope (CCAT) observatory. A planar 180º hybrid ring \ncoupler, two separate slotline antennas, two separate slotline to CPW transitions to employ for the 800-1100 GHz balanced SIS mixer, based on NbTiN circuitry, were designed and all were integrated on one 6 μm silicon substrate. \nAt the IF side of the integrated balanced mixers, two different configurations of superconducting \nintegrated 180º IF hybrids were designed to combine the two generated IF outputs at either Σ or Δ port depending on the choice of the input port of the hybrid. These 4-12 GHz IF hybrid coupler designs were based on planar lumped elements to miniaturize the size to about 0.5×2.2 μm^2. The designs were simulated for 500 μm and 9 μm silicon substrates. The latter is studied in order to integrate it at a later \nstage with the RF part of the mixer on one substrate. The lithography mask and subsequently the micro-fabrication of the IF hybrids were made. The measurement of the Nb based IF hybrid on a 500 μm silicon with Vector Network Analyzer (VNA) in liquid helium is reported. The measured results are analyzed and compared to the IF hybrid with the implemented superconducting Nb in the simulation. \n \nThese developments and designs will be available and applicable for future receivers of the CCAT-prime observatory. Because the original envisioned CCAT-observatory project was discontinued due to the lack of funding, it was decided that my 800-1100 GHz designs would not be further developed into working mixers for the time being and that other projects would get priority. \n \nMy work continued with the the development of integrated 1.9 THz balanced Hot Electron Bolometer (HEB) mixers. This development is relevant for 1.9 THz focal plane array receivers for the airborne Stratospheric Observatory for the Far Infrared (SOFIA), for which the mixers are developed in our group. The LO power consumption of the array presently limits its usable RF bandwidth. This power consumption could be reduced by a factor of 5 by using integrated balanced mixers. The mixers are based on superconducting NbN HEBs and Au is applied as normal metal to wire the mixers. The development contained design, micro-nanofabrication, DC and cryogenic high frequency measurements. All designed planar elements consisted of an 1 octave broadband 180º RF hybrid-ring coupler, two slotline tapered antennas, two slotline to \nCPW transitions, two or four 120 Ω HEB bridges, two low pass filters (LPFs) and two DC/IF blocking capacitors integrated on one 3 μm silicon substrate and simulated using CST suite. A further integrated 1.9 THz HEB mixer was designed to support the two separate IF outputs at one side of a 3 μm silicon substrate with employing a CPW-CPW crossover. \n \nThe micro-nanofabrication of the 1.9 THz balanced mixers was done in house using E-beam and photo-lithography techniques. Almost all DC measured devices contained HEB bridges that were sufficiently similar in normal state resistance and transition temperature. The average resistance of the devices, in the one available wafer for measurements, was about 17% too low. The transition temperature of the devices was around 7.9 K, in comparison to 8.5 K for our state of the art single pixel mixers. The two machined 1.9 THz balanced waveguide blocks for testing of the devices were machined in the institute's in house workshop. I have tested the transmission of the blocks, and thereby the workmanship, with a THz time Domain Spectrometer, showed about 2.4 dB of loss per mm waveguide length at room temperature, for a split block waveguide made of the oxygen free copper tellurium alloy (CuTe). \n \nThe cryogenic RF measurements showed a very similar LO-power coupling to both mixers in the balanced device, from both input ports of the mixer. By using an in house built Quantum Cascade Laser (QCL) LO as a local oscillator and a severely attenuated Virginia Diode multiplier chain (VDI) LO as a signal source I have shown proper balanced mixer behavior, thereby validating the design. Signal suppression up to 38 dB was shown by inverting the bias voltages on one of the mixers in the balanced device, which added a 180º phase change to the IF of one of the mixers.