Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Transactions on Terahertz Science and Technology

An SIS Mixer With 2hf/k DSB Noise Temperature at 163 - 211 GHz Band

Bhushan Billade, Alexey Pavolotsky, Victor Y. Belitsky

Published May 2, 2013• 21 citations
Publisher

Abstract

We present the design and the performance of a fixed-tuned, all niobium (Nb) Superconductor-Insulator-Superconductor (SIS) mixer covering RF frequencies from 163 to 211 GHz with 4-8 GHz IF bandwidth. The mixer uses two Nb/Al-AlOx/Nb junctions of size 3 μm2each with theRnAproduct of 30 Ω·μm2, in a twin junction configuration. An local oscillator (LO) directional coupler made of superconducting lines with slots in the ground plane is integrated on the SIS mixer chip. The isolated port of the LO coupler is terminated using a wide-band resistive load with a sheet resistance of 12 Ω/□. The SIS tuning circuitry is optimized to achieve best power match between the twin junctions and the embedding circuitry. The measurement of the double sideband mixer noise at 171 GHz shows that the receiver noise temperature is approximately 17 K, which is just 2hf/k. The estimated noise contribution from the RF loss and the IF chain at 176 GHz LO frequency is 8 K and 7.5 K respectively, resulting in a SIS mixer noise ofhf/2k. The mixer noise performance across the entire RF band varies between 19 to 25 K. This is to our knowledge the best reported noise temperature at these frequencies till now.

DOI
10.1109/tthz.2013.2255734

Related papers

Three Quanta Sensitivity Superconductor–Insulator–Superconductor Mixer for the 0.78–0.95 THz Band

Takafumi Kojima, M. Kroug, Masanori Takeda +5 more

We have successfully demonstrated a low-noise 0.78–0.95-THz waveguide mixer based on Nb/AlO x /Nb superconductor–insulator–superconductor (SIS) junctions integrated with an NbTiN/SiO 2 /Al superconducting inverted microstrip. The mixer employs a twin-junction tuning circuit and an impedance transformer which are designed to achieve both low noise and wideband operation. Corrected for optical input losses in front of the mixer, the double-sideband (DSB) noise temperature is below 120 K (<3 hf / k B ) around the local oscillator (LO) frequency of 0.88 THz and at an operating temperature of 2 K. The results represent state-of-the-art performance for mixers in the terahertz frequency range.

Applied Physics Express•Oct 9, 2009•26 citations

120~180 GHz 대역 SIS(Superconductor-Insulator-Superconductor)접합 믹서의 개발

Moon‐Hee Chung, Changhoon Lee, Kwang-Dong Kim +3 more

A fixed-tuned SIS(Superconductor-Insulator-Superconductor) mixer across 120∼180 GHz band has been developed. This mixer employs an SIS chip fabricated by Nobeyama radio observatory which consists of a series array of 6 Nb/Al-AlO/Nb junctions in a microstrip line on a fused quartz substrate. The SIS chip is placed at the center of the half-height waveguide mixer mount to have a good incoming signal coupling over the whole frequency band. No mechanical tuner was used in the SIS mixer and the RF signal and local oscillator power are injected to the mixer via a cooled cross-guide coupler. In order to prevent the IF signal loss, the If output impedance of the SIS mixer was matched to the 50 input impedance of the IF chain. Measured double sideband noise temperatures of a receiver using the SIS mixer are 32∼131 K over 120∼180 GHz band. The developed SIS mixer is now in use for radio astronomical observations on the TRAO 14 m radio telescope.

The Journal of Korean Institute of Electromagnetic Engineering and Science•Jan 1, 2004•4 citations

Low-noise integrated balanced SIS mixer for 787–950 GHz

Yasunori Fujii, Takafumi Kojima, Álvaro González +5 more

Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.

Superconductor Science and Technology•Nov 30, 2016•13 citations

A 100-GHz fixed-tuned waveguide SIS mixer exhibiting broad bandwidth and very low noise temperature

Sheng-Gai Shi, Takashi Noguchi, Junji Inatani

This paper presents design and performance data for a 100-GHz waveguide superconductor-insulator-superconductor (SIS) mixer, which is incorporated with a twin-junction device (i.e., two identical junctions connected in parallel through a tuning inductance) and a fixed-tuned broad-band waveguide mixer mount. The 100-GHz mixer is actually developed as a prototype of the 500-GHz one. The constructed 100-GHz SIS receiver results in an overall receiver noise temperature (DSB) of less than 40 K over the frequency range from 80-120 GHz, with a minimum value of just 20 K that is four times as large as the quantum limit (i.e., 4/spl planck//spl omega//k). Such a performance is comparable or even superior to those of the best mechanically tunable waveguide SIS receivers at the same frequency band. In addition, some interesting mixing behaviors related to this two-junction device are described in detail.

IEEE Transactions on Applied Superconductivity•Jan 1, 1997•22 citations

A Low-noise Balanced SIS Mixer for the 790-950 GHz Band

Takafumi Kojima, Yasunori FUJII, Yoshinori Uzawa

We have developed a low-noise balanced superconductor-insulator-superconductor (SIS) mixer using a waveguide 3-dB 90-degree hybrid coupler over the radio frequency (RF) range of 790-950 GHz and intermediate frequency range of 4-12 GHz at an operating temperature of 4 K. The RF coupler was carefully designed in regards to machining errors so that the entire amplitude imbalance including the mixer gain became smaller. The fabricated coupler was characterized at both room and cryogenic temperature. The receiver noise temperature of the balanced SIS mixer was below 350 K over the entire frequency band and the local oscillator (LO) noise rejection ratio was estimated to be more than 15 dB. This result is equivalent to state-ofthe-art mixer performance at this frequency range.

TEION KOGAKU (Journal of Cryogenics and Superconductivity Society of Japan)•Jan 1, 2014•2 citations

Performance Characterization of a 600-700 GHz SIS Mixer

M. J. Wang, Rey Chin, Wenlei Shan +4 more

A 600-700GHz SIS mixer with the twin-junction tuning circuit has been designed and fabricated [1] The surface impedance of thin-film superconducting microstrip lines, based on Mattis-Bardeen theory [2], is included in the optimization of RF impedance matching. The receiver noise temperature measured in the frequency range of 630-660GHz is below 200K and the lowest receiver noise temperature of 181K is achieved at 656GHz. The FTS response of the SIS mixer shows a good RF coupling from 600GHz to 700GHz. Both the noise performance and the FTS response can be quantitatively described by numerical results using the quantum theory of mixing. Some detail considerations on the mixer model calculation, such as spreading inductance around the junction tuning structure and mixer's embedding impedance, are discussed. Introduction Nb-based superconductor-insulator-superconductor (SIS) mixers have been used very successfully in sub-mm wavelength detection. Their receiver noise temperature has reached to three times the quantum limit, —3 hfrkB, below the junction's gap frequency. However, at high frequency bands, Nb SIS mixers need to be designed carefully because the photon energy is close to or higher than the gap energy of Nb, A-1.4meV. When the frequency band covers the gap frequency of Nb, —670GHz, the RF loss of Nb superconducting transmission lines increases dramatically and the surface impedance has strong frequency dependence. Usually, the RF properties of a superconducting transmission line can be described by the Mattis-Bardeen theory [2] in good accuracy. From results reported so far [4-9], the best receiver noise temperature is close to 5 hi7kB in the band of 600-700GHz. Despite of the input loss contributed by the experimental setup, some other properties of SIS mixers should be taken into account. In this paper, we characterize the performance of a 600-700GHz mixer by comparing the experimental and simulated results.

Softwaretechnik-Trends•Mar 1, 2002•1 citation
We present the design and the performance of a fixed-tuned, all niobium (Nb) Superconductor-Insulator-Superconductor (SIS) mixer covering RF frequencies from 163 to 211 GHz with 4-8 GHz IF bandwidth. The mixer uses two Nb/Al-AlOx/Nb junctions of size 3 μm2each with theRnAproduct of 30 Ω·μm2, in a twin junction configuration. An local oscillator (LO) directional coupler made of superconducting lines with slots in the ground plane is integrated on the SIS mixer chip. The isolated port of the LO coupler is terminated using a wide-band resistive load with a sheet resistance of 12 Ω/□. The SIS tuning circuitry is optimized to achieve best power match between the twin junctions and the embedding circuitry. The measurement of the double sideband mixer noise at 171 GHz shows that the receiver noise temperature is approximately 17 K, which is just 2hf/k. The estimated noise contribution from the RF loss and the IF chain at 176 GHz LO frequency is 8 K and 7.5 K respectively, resulting in a SIS mixer noise ofhf/2k. The mixer noise performance across the entire RF band varies between 19 to 25 K. This is to our knowledge the best reported noise temperature at these frequencies till now.
We have successfully demonstrated a low-noise 0.78–0.95-THz waveguide mixer based on Nb/AlO x /Nb superconductor–insulator–superconductor (SIS) junctions integrated with an NbTiN/SiO 2 /Al superconducting inverted microstrip. The mixer employs a twin-junction tuning circuit and an impedance transformer which are designed to achieve both low noise and wideband operation. Corrected for optical input losses in front of the mixer, the double-sideband (DSB) noise temperature is below 120 K (<3 hf / k B ) around the local oscillator (LO) frequency of 0.88 THz and at an operating temperature of 2 K. The results represent state-of-the-art performance for mixers in the terahertz frequency range.
A fixed-tuned SIS(Superconductor-Insulator-Superconductor) mixer across 120∼180 GHz band has been developed. This mixer employs an SIS chip fabricated by Nobeyama radio observatory which consists of a series array of 6 Nb/Al-AlO/Nb junctions in a microstrip line on a fused quartz substrate. The SIS chip is placed at the center of the half-height waveguide mixer mount to have a good incoming signal coupling over the whole frequency band. No mechanical tuner was used in the SIS mixer and the RF signal and local oscillator power are injected to the mixer via a cooled cross-guide coupler. In order to prevent the IF signal loss, the If output impedance of the SIS mixer was matched to the 50 input impedance of the IF chain. Measured double sideband noise temperatures of a receiver using the SIS mixer are 32∼131 K over 120∼180 GHz band. The developed SIS mixer is now in use for radio astronomical observations on the TRAO 14 m radio telescope.
Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.
This paper presents design and performance data for a 100-GHz waveguide superconductor-insulator-superconductor (SIS) mixer, which is incorporated with a twin-junction device (i.e., two identical junctions connected in parallel through a tuning inductance) and a fixed-tuned broad-band waveguide mixer mount. The 100-GHz mixer is actually developed as a prototype of the 500-GHz one. The constructed 100-GHz SIS receiver results in an overall receiver noise temperature (DSB) of less than 40 K over the frequency range from 80-120 GHz, with a minimum value of just 20 K that is four times as large as the quantum limit (i.e., 4/spl planck//spl omega//k). Such a performance is comparable or even superior to those of the best mechanically tunable waveguide SIS receivers at the same frequency band. In addition, some interesting mixing behaviors related to this two-junction device are described in detail.
We have developed a low-noise balanced superconductor-insulator-superconductor (SIS) mixer using a waveguide 3-dB 90-degree hybrid coupler over the radio frequency (RF) range of 790-950 GHz and intermediate frequency range of 4-12 GHz at an operating temperature of 4 K. The RF coupler was carefully designed in regards to machining errors so that the entire amplitude imbalance including the mixer gain became smaller. The fabricated coupler was characterized at both room and cryogenic temperature. The receiver noise temperature of the balanced SIS mixer was below 350 K over the entire frequency band and the local oscillator (LO) noise rejection ratio was estimated to be more than 15 dB. This result is equivalent to state-ofthe-art mixer performance at this frequency range.
A 600-700GHz SIS mixer with the twin-junction tuning circuit has been designed and fabricated [1] The surface impedance of thin-film superconducting microstrip lines, based on Mattis-Bardeen theory [2], is included in the optimization of RF impedance matching. The receiver noise temperature measured in the frequency range of 630-660GHz is below 200K and the lowest receiver noise temperature of 181K is achieved at 656GHz. The FTS response of the SIS mixer shows a good RF coupling from 600GHz to 700GHz. Both the noise performance and the FTS response can be quantitatively described by numerical results using the quantum theory of mixing. Some detail considerations on the mixer model calculation, such as spreading inductance around the junction tuning structure and mixer's embedding impedance, are discussed. Introduction Nb-based superconductor-insulator-superconductor (SIS) mixers have been used very successfully in sub-mm wavelength detection. Their receiver noise temperature has reached to three times the quantum limit, —3 hfrkB, below the junction's gap frequency. However, at high frequency bands, Nb SIS mixers need to be designed carefully because the photon energy is close to or higher than the gap energy of Nb, A-1.4meV. When the frequency band covers the gap frequency of Nb, —670GHz, the RF loss of Nb superconducting transmission lines increases dramatically and the surface impedance has strong frequency dependence. Usually, the RF properties of a superconducting transmission line can be described by the Mattis-Bardeen theory [2] in good accuracy. From results reported so far [4-9], the best receiver noise temperature is close to 5 hi7kB in the band of 600-700GHz. Despite of the input loss contributed by the experimental setup, some other properties of SIS mixers should be taken into account. In this paper, we characterize the performance of a 600-700GHz mixer by comparing the experimental and simulated results.