Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEICE Transactions on Electronics

Waveguide-Type SIS Receiver Using All-NbN Technique

M. TAKEDA

Published Feb 1, 2006• 5 citations
Publisher

Abstract

This paper describes the first experimental results for a waveguide-type all-NbN superconductor-insulator-superconductor (SIS) heterodyne mixer on an MgO substrate designed to operate over the gap frequency of Nb. The mixer consists of an NbN/MgO/NbN junction, which has a length of one wavelength at 880GHz as a tuning circuit, an NbN/MgO/NbN microstrip as a λ/4 impedance transformer, and an RF choke filter. The mixer chip was designed using a high-frequency-structure simulator. Its return-loss and embedding-impedance characteristics were examined using a 180-times-scaled mixer model. By optimizing the cutting and polishing processes for the MgO substrate, we were able to fabricate the mixer chip with an accuracy of less than 5 μm. We succeeded in mounting the chip on a mixer block and in estimating the receiver noise temperature. The uncorrected minimum double-sideband receiver noise temperature was 740 K at 824 GHz. A comparison of the receiver noise temperature in a quasi-optical SIS mixer fabricated on the same wafer as the waveguide mixer showed that input noise was the major contributor to receiver noise in the waveguide mixer.

DOI
10.1093/ietele/e89-c.2.163

Related papers

Waveguide-type all-NbN SIS mixers on MgO substrates

Masanori Takeda, Yoshinori Uzawa, Akira Kawakami +2 more

We present the first experimental results on waveguide-type all-NbN SIS receivers fabricated on MgO substrates designed in a frequency range from 780 to 960 GHz. The receiver has a resonant distributed SIS junction one wavelength long at 870 GHz as the tuning circuit and a diagonal feed horn. The mixer chip was fabricated with accuracies of less than 10 im in width and +/5 jam in thickness by optimizing the cutting and polishing conditions for MgO substrates and was successfully mounted in a waveguide-mixer block. Using a conventional Y-factor method for receiver noise measurement, a minimum DSB receiver noise temperature of 700 K was obtained at an LO frequency of 770 GHz. The contribution to noise made by the input system was dominant in receiver noise and the input noise temperature was more than 300 K over the measured band.

Softwaretechnik-Trends•Jan 1, 2004•1 citation

Development of a waveguide NbN-based SIS mixer in the 900-GHz band

Mahoto Takeda, Yoshinori Uzawa, Zhen Wang +2 more

We have designed and fabricated waveguide superconductor-insulator-superconductor (SIS) receivers at 870 GHz with NbN/AlN/NbN tunnel junctions on an MgO substrate. A waveguide probe was incorporated into the mixer chip for a waveguide-to-microstrip transition. As the tuning circuit for the SIS mixer, we designed a resonant distributed junction whose length is one wavelength and critical current density is 20 kA/cm/sup 2/. The mixing properties were calculated based on the quantum theory of mixing. The SSB mixer noise temperature should be less than 100 K and conversion gain larger than -8.0 dB in the frequency range from 840 to 920 GHz. We also observed the resonance steps of the fabricated SIS mixer. The tuning frequency was slightly higher than the designed frequency.

IEEE Transactions on Applied Superconductivity•Jun 1, 2003•6 citations

Low-noise waveguide SIS mixer with NbN/AlN/NbN tunnel junctions tuned by an NbN/MgO/NbTiN microstrip circuit

Masanori Takeda, Wenlei Shan, Takafumi Kojima +4 more

The low-noise performance of a waveguide SIS mixer with NbN/AlN/NbN tunnel junctions and an NbN/MgO/NbTiN tuning circuit on an MgO substrate was demonstrated at frequencies above the gap frequency of Nb. To design the mixer, the complex refractive index of the MgO substrate was measured by using a THz time-domain spectrometer. The superconductive properties of NbTiN films on MgO were examined in detail. An uncorrected receiver noise temperature of 262 K (DSB) at 820 GHz was achieved in an IF bandwidth of 4-12 GHz at a bath temperature of 4.2 K. By comparing the measured and calculated conversion gains, the loss in the NbN/MgO/NbTiN tuning circuit was estimated to be 0.98 dB at 810 GHz.

Superconductor Science and Technology•Jun 10, 2009•10 citations

0.5-THz waveguide SIS mixers with NbN/AlN/NbN technology

Jing Li, Masanori Takeda, Zhen Wang +1 more

Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Nov 29, 2007•3 citations

A submillimetre-wave SIS mixer using NbN/MgO/NbN trilayers grown epitaxially on an MgO substrate

Yoshinori Uzawa, Akira Kawakami, Atsushi SAITO +2 more

We have designed, fabricated and tested a quasi-optical superconductor–insulator–superconductor (SIS) mixer employing distributed NbN/MgO/NbN tunnel junctions and NbN/MgO/NbN microstriplines at submillimetre-wave frequencies. These trilayers were fabricated by dc- and rf-magnetron sputtering on an MgO substrate at ambient temperature so that the NbN and MgO films were grown epitaxially. Our SIS mixer consists of an MgO hyperhemispherical lens with an antireflection cap and a self-complementary log-periodic antenna made of a single-crystal NbN film, on which the distributed SIS junctions and the two-section impedance transformers were mirror-symmetrically placed at the feed point of the antenna. As designed, the junctions are 0.6 μm wide and 15.5 μm long, which is sufficient to absorb the incoming signal along this lossy transmission line, assuming a current density of 10 kA cm −2 . The mixer showed good I – V characteristics, with subgap-to-normal resistance ratios of about 13, although weak-link breaks were observed above the gap voltage. The minimum double side band receiver noise temperature was 334 K at 678 GHz, including the input noise of about 200 K as estimated by the standard technique. The noise temperature gradually rose to 672 K at 820 GHz. This behaviour may be caused by RF losses from the weak-link parts, due to the steps between the distributed junctions and the microstriplines being less than 1 μm wide.

Superconductor Science and Technology•Nov 21, 2002•6 citations

Wide-band operation of quasi-optical distributed superconductor/insulator/superconductor mixers with epitaxial NbN/AlN/NbN junctions

Satoshi Kohjiro, S. V. Shitov, Z Wang +4 more

For the optimum design of integrated receivers operating above the gap frequency of Nb, we have designed, fabricated and tested NbN-based quasi-optical superconductor/insulator/superconductor (SIS) mixers. The mixer chip incorporates a resonant half-wavelength epitaxial NbN/AlN/NbN junction, a twin-slot antenna and their coupling circuits. We adopted two kinds of coupling circuit between the antenna and the SIS junction: one is an in-phase feed with a length of 95 µm and the other is an anti-phase feed of 30 µm length. It was found that the anti-phase mixer reveals a 3 dB bandwidth of 43% of the centre frequency; the uncorrected double-sideband receiver noise temperature TRX = 691 K at 0.91 THz and TRX = 844 K at 0.80 THz, while 17% and TRX = 1250 K at 0.79 THz for the in-phase version. Possible reasons for this difference are discussed, which could be transmission loss and its robustness with respect to the variation of junction parameters. These experimental results suggest the NbN-based distributed mixer with the anti-phase feed is a better candidate for wide-band integrated receivers operating above 0.7 THz.

Superconductor Science and Technology•Apr 6, 2004•2 citations
This paper describes the first experimental results for a waveguide-type all-NbN superconductor-insulator-superconductor (SIS) heterodyne mixer on an MgO substrate designed to operate over the gap frequency of Nb. The mixer consists of an NbN/MgO/NbN junction, which has a length of one wavelength at 880GHz as a tuning circuit, an NbN/MgO/NbN microstrip as a λ/4 impedance transformer, and an RF choke filter. The mixer chip was designed using a high-frequency-structure simulator. Its return-loss and embedding-impedance characteristics were examined using a 180-times-scaled mixer model. By optimizing the cutting and polishing processes for the MgO substrate, we were able to fabricate the mixer chip with an accuracy of less than 5 μm. We succeeded in mounting the chip on a mixer block and in estimating the receiver noise temperature. The uncorrected minimum double-sideband receiver noise temperature was 740 K at 824 GHz. A comparison of the receiver noise temperature in a quasi-optical SIS mixer fabricated on the same wafer as the waveguide mixer showed that input noise was the major contributor to receiver noise in the waveguide mixer.
We present the first experimental results on waveguide-type all-NbN SIS receivers fabricated on MgO substrates designed in a frequency range from 780 to 960 GHz. The receiver has a resonant distributed SIS junction one wavelength long at 870 GHz as the tuning circuit and a diagonal feed horn. The mixer chip was fabricated with accuracies of less than 10 im in width and +/5 jam in thickness by optimizing the cutting and polishing conditions for MgO substrates and was successfully mounted in a waveguide-mixer block. Using a conventional Y-factor method for receiver noise measurement, a minimum DSB receiver noise temperature of 700 K was obtained at an LO frequency of 770 GHz. The contribution to noise made by the input system was dominant in receiver noise and the input noise temperature was more than 300 K over the measured band.
We have designed and fabricated waveguide superconductor-insulator-superconductor (SIS) receivers at 870 GHz with NbN/AlN/NbN tunnel junctions on an MgO substrate. A waveguide probe was incorporated into the mixer chip for a waveguide-to-microstrip transition. As the tuning circuit for the SIS mixer, we designed a resonant distributed junction whose length is one wavelength and critical current density is 20 kA/cm/sup 2/. The mixing properties were calculated based on the quantum theory of mixing. The SSB mixer noise temperature should be less than 100 K and conversion gain larger than -8.0 dB in the frequency range from 840 to 920 GHz. We also observed the resonance steps of the fabricated SIS mixer. The tuning frequency was slightly higher than the designed frequency.
The low-noise performance of a waveguide SIS mixer with NbN/AlN/NbN tunnel junctions and an NbN/MgO/NbTiN tuning circuit on an MgO substrate was demonstrated at frequencies above the gap frequency of Nb. To design the mixer, the complex refractive index of the MgO substrate was measured by using a THz time-domain spectrometer. The superconductive properties of NbTiN films on MgO were examined in detail. An uncorrected receiver noise temperature of 262 K (DSB) at 820 GHz was achieved in an IF bandwidth of 4-12 GHz at a bath temperature of 4.2 K. By comparing the measured and calculated conversion gains, the loss in the NbN/MgO/NbTiN tuning circuit was estimated to be 0.98 dB at 810 GHz.
Heterodyne mixers based on superconducting SIS (superconductor-insulator-superconductor) tunnel junctions have been demonstrated to be the most sensitive coherent detectors at millimeter and submillimeter wavelengths. In fact, conventional superconducting SIS mixers with Nb/AlOx/Nb junction and Nb/SiO2/Nb tuning circuit have shown good performances with the noise temperature reaching as low as three times the quantum limit below 0.7THz, which is the gap frequency of Nb-based SIS junctions. However, due to the large loss in Nb thin-film superconducting microstrip lines, the noise performance of Nb SIS mixers deteriorates significantly above 0.7THz. With a gap frequency double that of Nb-based SIS junctions, NbN-based SIS junctions are of particular interest for the development of heterodyne mixers in the terahertz region. Considering the bandwidth and output power of local-oscillator (LO) signal sources are quite limited around 1THz, we firstly develop a waveguide NbN-based SIS mixer at 0.5THz. Three types of SIS junctions, i.e., long junction, parallel-connected tunnel junction (PCTJ) and distributed junction array (DJ) are investigated. They are all comprised of NbN-AlN-NbN tri-layer fabricated on an MgO substrate and have the same current density (Jc) of 10kA/cm2. In this paper, we describe their design, fabrication and preliminary experimental results.
We have designed, fabricated and tested a quasi-optical superconductor–insulator–superconductor (SIS) mixer employing distributed NbN/MgO/NbN tunnel junctions and NbN/MgO/NbN microstriplines at submillimetre-wave frequencies. These trilayers were fabricated by dc- and rf-magnetron sputtering on an MgO substrate at ambient temperature so that the NbN and MgO films were grown epitaxially. Our SIS mixer consists of an MgO hyperhemispherical lens with an antireflection cap and a self-complementary log-periodic antenna made of a single-crystal NbN film, on which the distributed SIS junctions and the two-section impedance transformers were mirror-symmetrically placed at the feed point of the antenna. As designed, the junctions are 0.6 μm wide and 15.5 μm long, which is sufficient to absorb the incoming signal along this lossy transmission line, assuming a current density of 10 kA cm −2 . The mixer showed good I – V characteristics, with subgap-to-normal resistance ratios of about 13, although weak-link breaks were observed above the gap voltage. The minimum double side band receiver noise temperature was 334 K at 678 GHz, including the input noise of about 200 K as estimated by the standard technique. The noise temperature gradually rose to 672 K at 820 GHz. This behaviour may be caused by RF losses from the weak-link parts, due to the steps between the distributed junctions and the microstriplines being less than 1 μm wide.
For the optimum design of integrated receivers operating above the gap frequency of Nb, we have designed, fabricated and tested NbN-based quasi-optical superconductor/insulator/superconductor (SIS) mixers. The mixer chip incorporates a resonant half-wavelength epitaxial NbN/AlN/NbN junction, a twin-slot antenna and their coupling circuits. We adopted two kinds of coupling circuit between the antenna and the SIS junction: one is an in-phase feed with a length of 95 µm and the other is an anti-phase feed of 30 µm length. It was found that the anti-phase mixer reveals a 3 dB bandwidth of 43% of the centre frequency; the uncorrected double-sideband receiver noise temperature TRX = 691 K at 0.91 THz and TRX = 844 K at 0.80 THz, while 17% and TRX = 1250 K at 0.79 THz for the in-phase version. Possible reasons for this difference are discussed, which could be transmission loss and its robustness with respect to the variation of junction parameters. These experimental results suggest the NbN-based distributed mixer with the anti-phase feed is a better candidate for wide-band integrated receivers operating above 0.7 THz.