Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Conference on Precision Electromagnetic Measurements

Quantum Voltage Characteristics of High-Temperature Superconducting Josephson Junction Arrays with Varied Junction Widths

Da Xu, Yafang Lian, Changhao Zhao, Yunlin Liu, Jifeng Qu, Jianting Zhao

Published Sep 1, 2026• 0 citations
Publisher

Abstract

High-temperature superconducting (HTS) Josephson junction (JJ) arrays with varied junction widths of 2-5 μm were fabricated on REBCO/Au-coated (La,Sr)(Al,Ta)O3 (LSAT) bicrystal substrates for quantum voltage standard applications. The HTS JJ arrays, consisting of five Josephson junctions connected in series, were irradiated via a Fabry-Pérot resonator. The HTS JJ series array with a 5 μm junction width exhibits the best overall performance. Under 66.72 GHz microwave irradiation at 77 K, the 5 μm-wide junction array exhibits a second-order quantum voltage of 1.3794 mV with a step width of 250 μA and voltage fluctuation of within 0.1 μV. At a lower temperature of 58.66 K and 69.516 GHz microwave irradiation, the same device produced a stable quantum voltage of 8.0494 mV, corresponding to the 11th to 12th order steps, with a step width of 100 μA and voltage fluctuation also confined to 0.1 μV.

DOI
10.1109/cpem68396.2026.11756291

Related papers

Metrological Study of YBCO Josephson Junction Arrays Integrated in a Fabry-Perot Resonator

A. Sosso, Domenico Andreone, V. Lacquaniti +3 more

The application of high temperature superconductor Josephson junctions to voltage metrology is promising for many reasons, beyond the evident advantage of simplified cryogenics and reduced costs of the apparatus. Owing to their intrinsic non-hysteretic behavior, arrays of shunted bicrystal YBCO junctions are particularly interesting for the realization of an AC voltage standard with quantum accuracy. Moreover, shunted bicrystal YBCO junctions arrays are advantageous because of the reduced area of the junctions, the wide range of characteristic voltages, and large critical currents. However, some specific problems arise, like possible effects related to the higher operating temperature. Furthermore, fabrication technology sets tight constraints on the design of structures for the distribution of microwave currents along the array junctions. We investigated the step properties under millimeter wave irradiation at frequencies about 75 GHz of HTS junction and arrays prepared on bicrystal substrates having grain boundaries. High sensitivity techniques were adopted to evaluate the step flatness at nV level and assess the accuracy of the step voltage. A new method that makes use of an open resonator, was implemented to irradiate the array, providing synchronization of a large number of junctions.

IEEE Transactions on Applied Superconductivity•Jun 1, 2007•9 citations

Optimization of the coupling of mm wave power to arrays of high-TcJosephson junctions

Alexander M. Klushin, M He, M. Levitchev +2 more

We explored high-temperature superconductor Josephson junction arrays embedded in a hemispherical Fabry-Perot resonator. We compared the characteristics of three designs of arrays to achieve steps at higher voltage with a better coupling to the millimeter wave irradiation power. With an optimal design, we achieved a maximum Josephson voltage of about 0.1V for an array of 620 bicrystal junctions at a temperature of 79.2K and a frequency of 77.465 GHz. Also steps from 0.01 V up to 0.1 V were observed. Our results showed that such circuits are challenging for applications in quantum voltage metrology. It is important to note that our quasioptical coupling method can be extended up to terahertz frequencies.

Journal of Physics Conference Series•Feb 1, 2008•8 citations

Superconductor-normal-superconductor junctions for programmable voltage standards

S. P. Benz

Series arrays of Nb–PdAu–Nb Josephson junctions were fabricated with characteristics ideally suited for application in programmable voltage standards and D/A converters with fundamental accuracy. Large arrays of junctions with applied microwave power showed constant voltage steps with current amplitudes as large as 7 mA. A novel coplanar waveguide design enabled uniform microwave power coupling to a five-segment array of 8192 junctions, so each segment had constant voltage steps over the same bias range. The 8192-junction device generated 1.1 mA steps at 186 mV with 11 GHz power and a maximum constant voltage step of 260 mV at 15.34 GHz.

Applied Physics Letters•Oct 30, 1995•131 citations

Constant-voltage steps at 0.1 Volt from a series array of high-Tc Josephson junctions

Alexander M. Klushin, Min He, Alexander S. Katkov

By employing an array of 620 high-TcJosephson junctions, we have achieved a maximum quantum output voltage with approximate value of 0.1 V at a temperature of 79.2 K and a frequency of 77.465 GHz. We also demonstrate that steps on the current-voltage characteristic of an array of bicrystal junctions at voltages of 70 mV were flat over the current range of 150 muA with a relative uncertainty of 0.04 ppm.

Conference on Precision Electromagnetic Measurements•Jun 1, 2008•2 citations

Development and investigation of Nb-Al-oxide-Nb Josephson junction arrays [voltage standard application]

A.F. Bochanov, V.D. Gelikonova, Alexander M. Klushin +2 more

An array of 3072 Josephson junctions Nb-AlO/sub x/-Nb is developed at IEM "KVARZ". Some preliminary results of an investigation of I-V curves under microwave irradiation in the 70 GHz frequency band are given. Zero current quantized voltage steps are displayed up to 450 mV with an amplitude >100 /spl mu/A. An improvement of the fabrication process, which is in progress, will enable to increase quantized voltage steps region up to 1 V.>

Conference on Precision Electromagnetic Measurements•Dec 17, 2002•0 citations

Noise Analysis for Millimeter-Wave Driving of High-Temperature Superconductor Josephson Junction Arrays

Changhao Zhao, Yafang Lian, Da Xu +6 more

High-temperature superconductor Josephson junction arrays were irradiated with millimeter-wave of approximately 70 GHz. The junction arrays were composed of 15 bicrystal YBCO junctions in series and produced DC voltage output of up to 2 mV, which was sampled by a commercial nanovoltmeter. The measured Vppof voltage fluctuations was on the order of 0.6 μV, exceeding the intrinsic fluctuation of the nanovoltmeter itself. To identify the origin of the excessive fluctuations, the phase noise and harmonic distortion of the millimeter-wave signal were analyzed and finally excluded from the major cause of the performance degradation. While millimeter-wave filtering and DC wiring of the apparatus can be improved, the results showed the feasibility of the millimeter-wave driving architecture and the noise analysis framework can be applied to development of even higher frequency drives into THz range.

Conference on Precision Electromagnetic Measurements•Sep 1, 2026•0 citations
High-temperature superconducting (HTS) Josephson junction (JJ) arrays with varied junction widths of 2-5 μm were fabricated on REBCO/Au-coated (La,Sr)(Al,Ta)O3 (LSAT) bicrystal substrates for quantum voltage standard applications. The HTS JJ arrays, consisting of five Josephson junctions connected in series, were irradiated via a Fabry-Pérot resonator. The HTS JJ series array with a 5 μm junction width exhibits the best overall performance. Under 66.72 GHz microwave irradiation at 77 K, the 5 μm-wide junction array exhibits a second-order quantum voltage of 1.3794 mV with a step width of 250 μA and voltage fluctuation of within 0.1 μV. At a lower temperature of 58.66 K and 69.516 GHz microwave irradiation, the same device produced a stable quantum voltage of 8.0494 mV, corresponding to the 11th to 12th order steps, with a step width of 100 μA and voltage fluctuation also confined to 0.1 μV.
The application of high temperature superconductor Josephson junctions to voltage metrology is promising for many reasons, beyond the evident advantage of simplified cryogenics and reduced costs of the apparatus. Owing to their intrinsic non-hysteretic behavior, arrays of shunted bicrystal YBCO junctions are particularly interesting for the realization of an AC voltage standard with quantum accuracy. Moreover, shunted bicrystal YBCO junctions arrays are advantageous because of the reduced area of the junctions, the wide range of characteristic voltages, and large critical currents. However, some specific problems arise, like possible effects related to the higher operating temperature. Furthermore, fabrication technology sets tight constraints on the design of structures for the distribution of microwave currents along the array junctions. We investigated the step properties under millimeter wave irradiation at frequencies about 75 GHz of HTS junction and arrays prepared on bicrystal substrates having grain boundaries. High sensitivity techniques were adopted to evaluate the step flatness at nV level and assess the accuracy of the step voltage. A new method that makes use of an open resonator, was implemented to irradiate the array, providing synchronization of a large number of junctions.
We explored high-temperature superconductor Josephson junction arrays embedded in a hemispherical Fabry-Perot resonator. We compared the characteristics of three designs of arrays to achieve steps at higher voltage with a better coupling to the millimeter wave irradiation power. With an optimal design, we achieved a maximum Josephson voltage of about 0.1V for an array of 620 bicrystal junctions at a temperature of 79.2K and a frequency of 77.465 GHz. Also steps from 0.01 V up to 0.1 V were observed. Our results showed that such circuits are challenging for applications in quantum voltage metrology. It is important to note that our quasioptical coupling method can be extended up to terahertz frequencies.
Series arrays of Nb–PdAu–Nb Josephson junctions were fabricated with characteristics ideally suited for application in programmable voltage standards and D/A converters with fundamental accuracy. Large arrays of junctions with applied microwave power showed constant voltage steps with current amplitudes as large as 7 mA. A novel coplanar waveguide design enabled uniform microwave power coupling to a five-segment array of 8192 junctions, so each segment had constant voltage steps over the same bias range. The 8192-junction device generated 1.1 mA steps at 186 mV with 11 GHz power and a maximum constant voltage step of 260 mV at 15.34 GHz.
High-temperature superconductor Josephson junction arrays were irradiated with millimeter-wave of approximately 70 GHz. The junction arrays were composed of 15 bicrystal YBCO junctions in series and produced DC voltage output of up to 2 mV, which was sampled by a commercial nanovoltmeter. The measured Vppof voltage fluctuations was on the order of 0.6 μV, exceeding the intrinsic fluctuation of the nanovoltmeter itself. To identify the origin of the excessive fluctuations, the phase noise and harmonic distortion of the millimeter-wave signal were analyzed and finally excluded from the major cause of the performance degradation. While millimeter-wave filtering and DC wiring of the apparatus can be improved, the results showed the feasibility of the millimeter-wave driving architecture and the noise analysis framework can be applied to development of even higher frequency drives into THz range.