The realization of fault-tolerant quantum computing requires the execution of quantum error-correction (QEC) schemes, to mitigate the fragile nature of qubits. In this context, to ensure the success of QEC, a protocol capable of implementing both qubit reset and leakage reduction is highly desirable together with the ability to perform fast and high-fidelity readout of the qubit s’ quantum states. In this thesis, we tackle both these challenges in an architecture consisting of fixed-frequency transmon qubits pair-wise coupled via tunable couplers. We demonstrate a readout scheme that combines two microwave techniques: applying a shelving technique to the qubits that reduces the contribution of decay error during readout, and a two-tone excitation of the readout resonators to distinguish among qubits’ populations in higher energy levels. We perform single-shot frequency-multiplexed qubit readout, with a 140 ns readout time, and demonstrate 99.5% assignment fidelity for two-state readout and 96.9% for three-state readout - without using a quantum-limited amplifier. We also demonstrate a reset scheme that is fast, unconditional, and achieves fidelities well above 99%, thus enabling fixed-frequency qubit architectures as future implementations of fault-tolerant quantum computers. Our reset protocol uses the tunable couplers to transfer any undesired qubits’ excitation to the readout resonators of the qubits, from which this excitation decays into the feedline. In total, the combination of qubit reset, leakage reduction, and coupler reset takes only 83 ns to complete. This reset protocol also provides a means to both reduce QEC cycle runtime and improve algorithmic fidelity on quantum processors.
The realization of fault-tolerant quantum computing requires the execution of quantum error-correction (QEC) schemes, to mitigate the fragile nature of qubits. In this context, to ensure the success of QEC, a protocol capable of implementing both qubit reset and leakage reduction is highly desirable together with the ability to perform fast and high-fidelity readout of the qubit s’ quantum states. In this thesis, we tackle both these challenges in an architecture consisting of fixed-frequency transmon qubits pair-wise coupled via tunable couplers. We demonstrate a readout scheme that combines two microwave techniques: applying a shelving technique to the qubits that reduces the contribution of decay error during readout, and a two-tone excitation of the readout resonators to distinguish among qubits’ populations in higher energy levels. We perform single-shot frequency-multiplexed qubit readout, with a 140 ns readout time, and demonstrate 99.5% assignment fidelity for two-state readout and 96.9% for three-state readout - without using a quantum-limited amplifier. We also demonstrate a reset scheme that is fast, unconditional, and achieves fidelities well above 99%, thus enabling fixed-frequency qubit architectures as future implementations of fault-tolerant quantum computers. Our reset protocol uses the tunable couplers to transfer any undesired qubits’ excitation to the readout resonators of the qubits, from which this excitation decays into the feedline. In total, the combination of qubit reset, leakage reduction, and coupler reset takes only 83 ns to complete. This reset protocol also provides a means to both reduce QEC cycle runtime and improve algorithmic fidelity on quantum processors.
Abstract On-demand qubit-state initialization is a prerequisite for quantum computation. We demonstrate such a protocol in a device consisting of fixed-frequency transmon qubits pair-wise coupled via tunable couplers — an architecture that is also compatible with the surface code. We use tunable couplers to transfer any undesired qubit excitation to the readout resonator of the qubit, from which this excitation decays into the feedline. In total, the combination of multi-level qubit reset, leakage reduction, and coupler reset takes only 88 ns to complete. Our reset scheme is fast, unconditional, and achieves fidelities above 99%, thus enabling fixed-frequency qubit architectures as future implementations of fault-tolerant quantum computers.
Abstract High-fidelity and rapid readout of a qubit state is key to quantum computing and communication, and it is a prerequisite for quantum error correction. We present a readout scheme for superconducting qubits that combines two microwave techniques: applying a shelving technique to the qubit that reduces the contribution of decay error during readout, and a two-tone excitation of the readout resonator to distinguish among qubit populations in higher energy levels. Using a machine-learning algorithm to post-process the two-tone measurement results further improves the qubit-state assignment fidelity. We perform single-shot frequency-multiplexed qubit readout, with a 140 ns readout time, and demonstrate 99.5% assignment fidelity for two-state readout and 96.9% for three-state readout–without using a quantum-limited amplifier.
Quantum error correction imposes stringent requirements on the underlying hardware: all core operations of a quantum processor – single-qubit gates, two-qubit entangling gates, qubit readout, and qubit reset – must operate well below the error thresholds of leading codes. While such thresholds have already been crossed in several platforms, the associated overhead in physical qubits and circuit depth remains extremely sensitive to the physical error rate. This thesis investigates how far a superconducting platform based on transmon qubits can be pushed toward its physical limits, and how architectural and control choices can be optimized to reduce the overhead required for fault-tolerant quantum computation. First, we develop and characterize tunable-coupler architectures that enable fast, high-fidelity controlled-Z (CZ) gates. A long-distance coupler increases the qubit-qubit separation, freeing chip area for additional on-chip components, while still achieving CZ fidelities above 99.8%. Building on this, we optimize the qubit-coupler coupling to simultaneously support high-performance single- and two-qubit gates. We achieve simultaneous single- and two-qubit gate fidelities exceeding 99.9% on the same chip using a CZ calibration experiment based on our phase-averaged leakage error amplification (PALEA) protocol. PALEA coherently amplifies small over- and under-rotations of the diabatic CZ gate, making calibration errors easier to detect and correct. Second, we address single-qubit gates. Using spectrally engineered FAST-DRAG and higherderivative DRAG pulses, we demonstrate sub-8 ns gates with errors of order 10!" and strongly suppressed leakage. Third, we address readout by combining shelving to a higher qubit level with Purcell-filtered resonators and quantum-limited amplification, achieving readout errors below 10!#. Beyond the transmon workhorse, we explore the unimon qubit, which combines large anharmonicity with reduced charge sensitivity, and investigate a quantum circuit refrigerator as an integrated resource for fast, unconditional qubit reset via engineered dissipation. Finally, we demonstrate a cryogenic microwave link between two dilution refrigerators, enabling remote state transfer and entanglement over a five-meter distance and illustrating a path toward modular and distributed superconducting quantum processors. Together, these results show that with careful co-design of device layout, coupling topology, pulse shaping, and calibration protocols, all core operations – except qubit reset – of a superconducting quantum processor can be operated in the 10!#–10!" error regime within a coherent hardware and control stack, substantially lowering the resource overhead required for future fault-tolerant architectures.
Superconducting qubits are a promising platform for building fault-tolerant quantum computers, with recent achievement showing the suppression of logical error with increasing code size. However, leakage into noncomputational states, a common issue in practical quantum systems including superconducting circuits, introduces correlated errors that undermine quantum error correction (QEC) scalability. Here, we propose and demonstrate a leakage reduction scheme utilizing tunable couplers, a widely adopted ingredient in large-scale superconducting quantum processors. Leveraging the strong frequency tunability of the couplers and stray interaction between the couplers and readout resonators, we eliminate state leakage on the couplers, thus suppressing space-correlated errors caused by population propagation among the couplers. Assisted by the couplers, we further reduce leakage to higher qubit levels with high efficiency (98.1%) and low error rate on the computational subspace (0.58%), suppressing time-correlated errors during QEC cycles. The performance of our scheme demonstrates its potential as an indispensable building block for scalable QEC with superconducting qubits.
Achieving high-fidelity qubit readout and reset while maintaining qubit coherence is crucial for quantum error correction and advanced quantum algorithms. Here, we design and experimentally demonstrate a scalable architecture based on frequency-tunable nonlinear Purcell filters, which enables flexible readout and rapid unconditional reset of multiple superconducting qubits. Our readout protocol dynamically adjusts the effective linewidth of the readout resonator through a tunable Purcell filter, optimizing the signal-to-noise ratio during measurement while suppressing photon noise during idle periods. Combined with a multilevel readout protocol, we achieve the highest readout fidelity of 99.3% without any quantum-limited amplifier, even with a small dispersive shift. Moreover, by leveraging a reset channel formed via the adjacent coupling between the filter and the coupler, we realize unconditional qubit reset of both leakage-induced |2⟩ and |1⟩ states within 200 ns and reset of the |1⟩ state alone within 75 ns, with error rates ≤1%. The filter also mitigates both photon-induced dephasing and the Purcell effect, thereby preserving qubit coherence. This scalable Purcell filter architecture shows exceptional performance in qubit readout, reset, and protection, marking it as a promising hardware component for advancing fault-tolerant quantum computing systems.
Fluxonium qubits combine long coherence times with strong anharmonicity, making them a promising platform for scalable superconducting quantum processors. Recent experiments have demonstrated high-fidelity operations in multi-qubit processors while suppressing stray qubit interactions using fluxonium-transmon-fluxonium (FTF) architectures. However, scaling such systems to larger arrays is constrained by a trade-off between achievable coupling strength, crosstalk suppression and qubit-qubit spacing required for wiring in a two-dimensional architecture. Multimode couplers, such as the double-transmon coupler (DTC), provide a promising pathway to overcome this limitation by enabling stronger interactions without compromising qubit spacing and isolation. Here, we develop a quantitative design framework for fluxonium-based quantum processors employing DTCs. Central to this work is a frequency-partitioned architecture that places qubit transitions, tunable-coupler excitations, and resonator modes in well-separated spectral regions. This structured allocation reduces parameter interdependence and enables the concurrent optimization of gate operations, readout, and qubit reset. By formulating device design as a multi-objective optimization problem under realistic experimental constraints and fabrication-induced disorder, we develop a tractable sequential workflow and determine a feasible parameter regime that simultaneously supports high-fidelity single- and two-qubit gates, fast qubit reset, and robust dispersive readout. These results establish a system-level architectural methodology that links circuit parameters to processor-level performance, and provide an experimentally actionable pathway toward scalable fluxonium quantum processors.