Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

EPJ Quantum Technology

Flux-bias-free flux qubit driven by low-power single-flux-quantum driver on monolithically integrated circuit

Duong Pham, Tomoharu Ueda, Shigeyuki Miyajima, Hirotaka Terai, K. Inomata, Masamitsu Tanaka, 藤巻朗, Taro Yamashita

Published Jul 9, 2026• 0 citations
Publisher

Abstract

Single-flux-quantum (SFQ) cryogenic control circuits are a promising approach for realizing scalable superconducting quantum processors. However, previous studies have primarily relied on conventional SFQ technologies with Josephson junction critical current densities ( \(J_{\mathrm{C}}\) ) of about 1 kA/cm 2 and critical currents ( \(I_{\mathrm{C}}\) ) of several hundred microamperes. Such large critical currents can increase power dissipation and induce nonequilibrium quasiparticles that degrade qubit performance. In this study, we demonstrate coherent control of a flux-bias-free (FBF) flux qubit using a low-power SFQ driver monolithically integrated on the same chip. The SFQ driver was fabricated using epitaxial NbN/AlN/NbN Josephson junctions with critical currents of only a few microamperes, approximately two orders of magnitude smaller than those used in conventional SFQ circuits. Using this low- \(I_{\mathrm{C}}\) SFQ driver, we found that the energy relaxation time, \(T_{1}\) , of the FBF qubit remains comparable to that obtained under conventional microwave control, indicating that the low- \(I_{\mathrm{C}}\) SFQ driver does not introduce a measurable degradation of qubit performance in the present device.

DOI
10.1140/epjqt/s40507-026-00538-3

Related papers

Fabrication Process for Monolithic Integration of a Nitride Superconductor-Based Superconducting Qubit with a Single Flux Quantum Control Circuit

Shigeyuki Miyajima, Taro Yamashita, Masamitsu Tanaka +3 more

We developed a process for fabricating nitride superconductor-based superconducting qubits monolithically integrated with a single flux quantum (SFQ)-based readout and control circuits. Since we used a Josephson junction (JJ) made of an NbN/AlN/NbN tri-layer, including a critical current density (Jc) of 50 A/cm2as the suitable material for superconducting qubits and SFQ readout/control circuits operating at 20 mK, the JJs for both the qubits and the SFQ circuits could simultaneously be fabricated. The device structure was also composed of three superconductive layers, comprising two superconductive layers as wiring layers and other layers as the top ground plane. Then, we used a Pd film as the resistive layer, which is required as the shunt resistors and the bias resistors for the SFQ control circuits, followed by an investigation of the properties of NbN/AlN/NbN epitaxial junctions and evaluation of the sheet inductance of the base NbN and wiring NbTiN layer. Our results showed the successful fabrication of a JJ with a sufficiently low leakage current and aJcof around 50 A/cm2, which was close to the target value. Furthermore, the evaluated sheet inductance exceeded 1 pH, which was several times larger than the values obtained for Nb-integrated circuits.

IEEE Transactions on Applied Superconductivity•Feb 1, 2023•11 citations

Design and Fabrication of Low-Power Single-Flux-Quantum Circuits Toward Quantum Bit Control

Masamitsu Tanaka, Yoshihiro Kitagawa, T. Satoh +1 more

We report low-power single-flux-quantum (SFQ) circuits fabricated with a lowered critical current density process and low-voltage design. We selected 250 A/cm$^{2}$to obtain 2–10 μA Josephson junctions (JJs) easily using conventional facilities. Our numerical simulation shows that the expected operating frequency is 10 GHz and that we can reduce the bias voltage to 0.1–0.5 mV; power consumption can be reduced to around 1 nW per JJ. We newly developed a fabrication process featuring four planarized Nb layers and a Pd resistor layer. We obtained the correct operation of several basic SFQ circuit elements designed with the lowered critical currents to 1/2 of the conventional circuits at 4.2 K. We also evaluated the Josephson junction critical currents, specific capacitance, resistance, and inductance at 3 K and 300 mK. We observed an increase of 7% in the critical currents at 300 mK, while the other parameters were unchanged. We demonstrated a 0.5-mV Josephson transmission line where we lowered the critical currents to 1/10. We expect such low-power SFQ circuits to operate at 20 mK, providing classical, general-purpose digital processing near quantum bits.

IEEE Transactions on Applied Superconductivity•Mar 2, 2023•15 citations

A Multi-Qubit SFQ Control Architecture Using Recycled Bias Current

Bicong Weng, Xue Zhang, Xiaoping Gao +3 more

High-frequency input signals from room-temperature microwave sources present a major bottleneck for scaling qubit numbers in universal quantum computers. To address this challenge, we previously developed a superconducting single-flux quantum (SFQ) qubit control circuit (SQCC) capable of generating precise SFQ pulse sequences using only DC bias. This approach eliminates traditional microwave signal chains and enables scalable, low-loss DC-based interconnects. However, as the number of SQCCs increases, the total required bias current grows linearly, leading to significant cable-induced thermal dissipation that limits scalability. In this work, we propose and implement an architecture using recycled bias current to scale up multiple SQCCs (RB-MSQCC). Theoretical analysis indicates that the recycling method can reduce thermal load by a factor of 100 to 1000 compared to conventional biasing. A key enabler of this architecture is a custom-designed driver-receiver pair (DRP) cell, which supports SFQ signal transmission across isolated ground planes using the SIMIT Nb03 process. Based on this, we demonstrate a 4-bit RB-MSQCC prototype. Experimental results confirm stable SFQ pulse generation across all four channels, with output frequencies ranging from 3.42 to 5.27 GHz, consistent with prior results (2.40-8.11 GHz). These findings validate the feasibility and robustness of the proposed scheme under current fabrication constraints. Our study offers both theoretical and experimental support for scalable, energy-efficient SFQ-based qubit control, representing a critical step toward large-scale superconducting quantum processors.

IEEE Transactions on Applied Superconductivity•Jan 16, 2026•0 citations

Comparative study of high-$J_{c}$ and low-$J_{c}$ SFQ microwave generators for transmon control

Hongxiang Shen, Wenhui Luo, Nobuyuki Yoshikawa

Abstract Scalability of superconducting quantum processors is increasingly constrained by the thermal load and wiring overhead associated with room-temperature control hardware. Cryogenic control interfaces based on single-flux-quantum (SFQ) logic offer a potential route to alleviating these bottlenecks, although their dissipation depends sensitively on the Josephson-junction critical current and the underlying fabrication process. In this work, we comparatively investigate SFQ-synthesized microwave generators implemented in high- and low-critical-current processes, and evaluate their suitability for transmon qubit control through a combination of experimental characterization and hybrid QuTiP–JoSIM analysis. By modulating SFQ pulse intervals, we synthesize coherent microwave drives and obtain single-qubit gate fidelities above 99.9% at 10 mK in QuTiP-based simulations for both implementations. The low- $J_{\mathrm{c}}$ J c implementation exhibits reduced phase-noise-induced error, achieves higher gate fidelity within its valid bias window, and shows improved robustness against frequency detuning, while the high- $J_{\mathrm{c}}$ J c implementation maintains a lower broadband noise floor. Using an explicit model of thermal dissipation and circuit footprint, we further estimate the integration limits of cryogenic control channels. The results show that reducing the switching current substantially relaxes the cooling-budget constraint and increases the number of channels that can be deployed simultaneously. These results clarify the trade-offs associated with implementing SFQ microwave generators in different fabrication processes and provide practical guidance for the design of scalable cryogenic qubit-control interfaces.

EPJ Quantum Technology•Apr 24, 2026•1 citation

Coherence-limited digital control of a superconducting qubit using a Josephson pulse generator at 3 K

M. A. Castellanos-Beltran, A. J. Sirois, L. Howe +4 more

Compared to traditional semiconductor control electronics (TSCE) located at room temperature, cryogenic single flux quantum (SFQ) electronics can provide qubit measurement and control alternatives that address critical issues related to scalability of cryogenic quantum processors. Single-qubit control and readout have been demonstrated recently using SFQ circuits coupled to superconducting qubits. Experiments where the SFQ electronics are co-located with the qubit have suffered from excess decoherence and loss due to quasiparticle poisoning of the qubit. A previous experiment by our group showed that moving the control electronics to the 3 K stage of the dilution refrigerator avoided this source of decoherence in a high-coherence 3D transmon geometry. In this paper, we also generate the pulses at the 3 K stage but have optimized the qubit design and control lines for scalable 2D transmon devices. We directly compare the qubit lifetime $T_1$, coherence time $T_2^*$ and gate fidelity when the qubit is controlled by the Josephson pulse generator (JPG) circuit versus the TSCE setup. We find agreement to within the daily fluctuations for $T_1$ and $T_2^*$, and agreement to within 10% for randomized benchmarking. We also performed interleaved randomized benchmarking on individual JPG gates demonstrating an average error per gate of $0.46$% showing good agreement with what is expected based on the qubit coherence and higher-state leakage. These results are an order of magnitude improvement in gate fidelity over our previous work and demonstrate that a Josephson microwave source operated at 3 K is a promising component for scalable qubit control.

quant-pharXiv:2512.07962•Applied Physics Letters•Dec 10, 2025•13 citations

Single Flux Quantum Circuit Operation at Millikelvin Temperatures

Jason Walter, Adam C. Weis, Kan-Ting Tsai +6 more

As quantum computing processors increase in size, there is growing interest in developing cryogenic electronics to overcome significant challenges to system scaling. Single flux-quantum (SFQ) circuits offer a promising alternative to remote, bulky, and power-hungry room temperature electronics. To meet the need for digital qubit control, readout, and co-processing, SFQ circuits must be adapted to operate at millikelvin temperatures near quantum processors. SEEQC's SFQuClass digital quantum management approach proximally places energy-efficient SFQ (ERSFQ) circuits and qubits in a multi-chip module. This enables extremely low power dissipation, compatible with a typical dilution cryostat's limited cooling power, while maintaining high processing speed and low error rates. We report on systematic testing from 4 K to 10 mK of a comprehensive set of ERSFQ cells, as well as more complex circuits such as programmable counters and demultiplexers used in digital qubit control. We compare the operating margins and error rates of these circuits and find that, at millikelvin, bias margins decrease and the center of the margins (i.e., the optimal bias current value) increases by ~15%, compared to 4.2 K. The margins can be restored by thermal annealing by reducing Josephson junction (JJ) critical current Ic. To provide guidance for how circuit parameters vary from 4.2 K to millikelvin, relevant analog process control monitors (PCMs) were tested in the temperature range of interest. The measured JJ critical current (of the PCM JJ arrays) increases by ~15% when decreasing temperature from 4.2 K to millikelvin, in good agreement with both theory and the empirically measured change in the center of bias margins for the tested digital circuits.

quant-pharXiv:2512.06895•IEEE Transactions on Applied Superconductivity•Dec 9, 2025•3 citations
Single-flux-quantum (SFQ) cryogenic control circuits are a promising approach for realizing scalable superconducting quantum processors. However, previous studies have primarily relied on conventional SFQ technologies with Josephson junction critical current densities ( (J_{\mathrm{C}}) ) of about 1 kA/cm 2 and critical currents ( (I_{\mathrm{C}}) ) of several hundred microamperes. Such large critical currents can increase power dissipation and induce nonequilibrium quasiparticles that degrade qubit performance. In this study, we demonstrate coherent control of a flux-bias-free (FBF) flux qubit using a low-power SFQ driver monolithically integrated on the same chip. The SFQ driver was fabricated using epitaxial NbN/AlN/NbN Josephson junctions with critical currents of only a few microamperes, approximately two orders of magnitude smaller than those used in conventional SFQ circuits. Using this low- (I_{\mathrm{C}}) SFQ driver, we found that the energy relaxation time, (T_{1}) , of the FBF qubit remains comparable to that obtained under conventional microwave control, indicating that the low- (I_{\mathrm{C}}) SFQ driver does not introduce a measurable degradation of qubit performance in the present device.
We developed a process for fabricating nitride superconductor-based superconducting qubits monolithically integrated with a single flux quantum (SFQ)-based readout and control circuits. Since we used a Josephson junction (JJ) made of an NbN/AlN/NbN tri-layer, including a critical current density (Jc) of 50 A/cm2as the suitable material for superconducting qubits and SFQ readout/control circuits operating at 20 mK, the JJs for both the qubits and the SFQ circuits could simultaneously be fabricated. The device structure was also composed of three superconductive layers, comprising two superconductive layers as wiring layers and other layers as the top ground plane. Then, we used a Pd film as the resistive layer, which is required as the shunt resistors and the bias resistors for the SFQ control circuits, followed by an investigation of the properties of NbN/AlN/NbN epitaxial junctions and evaluation of the sheet inductance of the base NbN and wiring NbTiN layer. Our results showed the successful fabrication of a JJ with a sufficiently low leakage current and aJcof around 50 A/cm2, which was close to the target value. Furthermore, the evaluated sheet inductance exceeded 1 pH, which was several times larger than the values obtained for Nb-integrated circuits.
We report low-power single-flux-quantum (SFQ) circuits fabricated with a lowered critical current density process and low-voltage design. We selected 250 A/cm2^{2}2to obtain 2–10 μA Josephson junctions (JJs) easily using conventional facilities. Our numerical simulation shows that the expected operating frequency is 10 GHz and that we can reduce the bias voltage to 0.1–0.5 mV; power consumption can be reduced to around 1 nW per JJ. We newly developed a fabrication process featuring four planarized Nb layers and a Pd resistor layer. We obtained the correct operation of several basic SFQ circuit elements designed with the lowered critical currents to 1/2 of the conventional circuits at 4.2 K. We also evaluated the Josephson junction critical currents, specific capacitance, resistance, and inductance at 3 K and 300 mK. We observed an increase of 7% in the critical currents at 300 mK, while the other parameters were unchanged. We demonstrated a 0.5-mV Josephson transmission line where we lowered the critical currents to 1/10. We expect such low-power SFQ circuits to operate at 20 mK, providing classical, general-purpose digital processing near quantum bits.
High-frequency input signals from room-temperature microwave sources present a major bottleneck for scaling qubit numbers in universal quantum computers. To address this challenge, we previously developed a superconducting single-flux quantum (SFQ) qubit control circuit (SQCC) capable of generating precise SFQ pulse sequences using only DC bias. This approach eliminates traditional microwave signal chains and enables scalable, low-loss DC-based interconnects. However, as the number of SQCCs increases, the total required bias current grows linearly, leading to significant cable-induced thermal dissipation that limits scalability. In this work, we propose and implement an architecture using recycled bias current to scale up multiple SQCCs (RB-MSQCC). Theoretical analysis indicates that the recycling method can reduce thermal load by a factor of 100 to 1000 compared to conventional biasing. A key enabler of this architecture is a custom-designed driver-receiver pair (DRP) cell, which supports SFQ signal transmission across isolated ground planes using the SIMIT Nb03 process. Based on this, we demonstrate a 4-bit RB-MSQCC prototype. Experimental results confirm stable SFQ pulse generation across all four channels, with output frequencies ranging from 3.42 to 5.27 GHz, consistent with prior results (2.40-8.11 GHz). These findings validate the feasibility and robustness of the proposed scheme under current fabrication constraints. Our study offers both theoretical and experimental support for scalable, energy-efficient SFQ-based qubit control, representing a critical step toward large-scale superconducting quantum processors.
Comparative study of high-JcJ_{c}Jc​ and low-JcJ_{c}Jc​ SFQ microwave generators for transmon control
Abstract Scalability of superconducting quantum processors is increasingly constrained by the thermal load and wiring overhead associated with room-temperature control hardware. Cryogenic control interfaces based on single-flux-quantum (SFQ) logic offer a potential route to alleviating these bottlenecks, although their dissipation depends sensitively on the Josephson-junction critical current and the underlying fabrication process. In this work, we comparatively investigate SFQ-synthesized microwave generators implemented in high- and low-critical-current processes, and evaluate their suitability for transmon qubit control through a combination of experimental characterization and hybrid QuTiP–JoSIM analysis. By modulating SFQ pulse intervals, we synthesize coherent microwave drives and obtain single-qubit gate fidelities above 99.9% at 10 mK in QuTiP-based simulations for both implementations. The low- JcJ_{\mathrm{c}}Jc​ J c implementation exhibits reduced phase-noise-induced error, achieves higher gate fidelity within its valid bias window, and shows improved robustness against frequency detuning, while the high- JcJ_{\mathrm{c}}Jc​ J c implementation maintains a lower broadband noise floor. Using an explicit model of thermal dissipation and circuit footprint, we further estimate the integration limits of cryogenic control channels. The results show that reducing the switching current substantially relaxes the cooling-budget constraint and increases the number of channels that can be deployed simultaneously. These results clarify the trade-offs associated with implementing SFQ microwave generators in different fabrication processes and provide practical guidance for the design of scalable cryogenic qubit-control interfaces.
Compared to traditional semiconductor control electronics (TSCE) located at room temperature, cryogenic single flux quantum (SFQ) electronics can provide qubit measurement and control alternatives that address critical issues related to scalability of cryogenic quantum processors. Single-qubit control and readout have been demonstrated recently using SFQ circuits coupled to superconducting qubits. Experiments where the SFQ electronics are co-located with the qubit have suffered from excess decoherence and loss due to quasiparticle poisoning of the qubit. A previous experiment by our group showed that moving the control electronics to the 3 K stage of the dilution refrigerator avoided this source of decoherence in a high-coherence 3D transmon geometry. In this paper, we also generate the pulses at the 3 K stage but have optimized the qubit design and control lines for scalable 2D transmon devices. We directly compare the qubit lifetime T1T_1T1​, coherence time T2∗T_2^*T2∗​ and gate fidelity when the qubit is controlled by the Josephson pulse generator (JPG) circuit versus the TSCE setup. We find agreement to within the daily fluctuations for T1T_1T1​ and T2∗T_2^*T2∗​, and agreement to within 10% for randomized benchmarking. We also performed interleaved randomized benchmarking on individual JPG gates demonstrating an average error per gate of 0.460.460.46% showing good agreement with what is expected based on the qubit coherence and higher-state leakage. These results are an order of magnitude improvement in gate fidelity over our previous work and demonstrate that a Josephson microwave source operated at 3 K is a promising component for scalable qubit control.
As quantum computing processors increase in size, there is growing interest in developing cryogenic electronics to overcome significant challenges to system scaling. Single flux-quantum (SFQ) circuits offer a promising alternative to remote, bulky, and power-hungry room temperature electronics. To meet the need for digital qubit control, readout, and co-processing, SFQ circuits must be adapted to operate at millikelvin temperatures near quantum processors. SEEQC's SFQuClass digital quantum management approach proximally places energy-efficient SFQ (ERSFQ) circuits and qubits in a multi-chip module. This enables extremely low power dissipation, compatible with a typical dilution cryostat's limited cooling power, while maintaining high processing speed and low error rates. We report on systematic testing from 4 K to 10 mK of a comprehensive set of ERSFQ cells, as well as more complex circuits such as programmable counters and demultiplexers used in digital qubit control. We compare the operating margins and error rates of these circuits and find that, at millikelvin, bias margins decrease and the center of the margins (i.e., the optimal bias current value) increases by ~15%, compared to 4.2 K. The margins can be restored by thermal annealing by reducing Josephson junction (JJ) critical current Ic. To provide guidance for how circuit parameters vary from 4.2 K to millikelvin, relevant analog process control monitors (PCMs) were tested in the temperature range of interest. The measured JJ critical current (of the PCM JJ arrays) increases by ~15% when decreasing temperature from 4.2 K to millikelvin, in good agreement with both theory and the empirically measured change in the center of bias margins for the tested digital circuits.