Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Symposium on VLSI Technology and Circuits (VLSI Technology and Circuits)

A Cryo-CMOS Fully-Integrated Superconducting Qubit Reflectometry Readout IC with FCNN-Based Adaptive Drift Mitigation and FIR-DSM-Based Stimulus TX

Yanshu Guo, Heyue Li, Xicheng Zhang, Jun Shi, Shijie Yin, Qichun Liu, Ning Deng, Zi Wang, Tiefu Li, G C Wang, Yuanjin Zheng, Hanjun Jiang

Published Jun 14, 2026• 0 citations
Publisher

Abstract

This work presents a neural-network augmented cryo-CMOS readout IC for superconducting quantum computing. With the FCNN-based qubit state detector, this IC achieves the ability of real-time qubit readout drift monitoring and adaptive drift mitigation. Adopting the FIR-DSM-based stimulus TX technique, the measured TX power is 2.6mW, which is$>1.9 \mathrm{x}$lower than prior designs. Quadrature digital-IF reflected RX is implemented with stimulus pulses synthesis and reflected signal processing, resulting in a fully-functional readout IC with a lowest power of 10.3mW. Verification with a transmon qubit at 4K, this IC achieves a readout fidelity up to 95.6%.

DOI
10.1109/vlsitechnologyandcir65830.2026.11577211

Related papers

Session 13 Overview: Cryo-CMOS for Quantum Computing

Denis C. Daly, Shawn S. H. Hsu, Edoardo Charbon A

Cryogenic CMOS (cryo-CMOS) support of quantum processors is becoming a necessity to ensure the continuous growth of qubit count, so as to achieve scalable, fault-tolerant quantum computers. The first paper of the session describes an integrated controller for spin qubits that performs state manipulation, readout, and gate pulsing fabricated in 22nm FinFET CMOS technology. The second paper presents a fully integrated SoC for spin qubit interface based on RF reflectometry of quantum dots, all implemented in 40nm CMOS technology, for scalable quantum systems operating at 3.5K. The third paper also focuses on scalable RF based readout of spin qubits for a record 0.17mW/qubit power requirement, operating at 4.2K. The fourth paper proposes a 1GS/s A/D converter for low-power digitization of the signal measured from a qubit readout that achieves a FOM of 15fJ/conv.-step at 4K.

Digest of technical papers/Digest of technical papers - IEEE International Solid-State Circuits Conference•Feb 13, 2021•0 citations

A Cryo-CMOS Homodyne-Demodulation Qubit Readout IC With Continuous-Time Analog Integration for SNR Improvement

Donggyu Minn, Kiseo Kang, Jaeho Lee +1 more

This paper presents a homodyne-demodulation readout IC with continuous-time direct analog integration for superconducting qubits. By integration at the analog frontend, the effective signal-to-noise ratio is efficiently increased, eliminating the need for a high-performance analog-to-digital converter and costly baseband processing for data recovery. The proposed IC, fabricated in 40 nm CMOS, is verified at 4 K in a dilution refrigerator. The readout fidelity, estimated under real-world conditions, is reported to be 99% within 300 ns.

IEEE Solid-State Circuits Letters•Jan 1, 2023•7 citations

A 28nm 6.5-8.1GHz 1.16mW/qubit Cryo-CMOS System-an-Chip for Superconducting Qubit Readout

Steven Van Winckel, Alican Çağlar, B. Gys +5 more

This paper presents a 28 nm cryo-CMOS system-on-chip (SoC) for the dispersive readout of superconducting qubits operating between 6.5-8.1 GHz at 4 K. The SoC includes a quadrature VCO and a full zero-IF transmitter and receiver chain, including 200 MS/s7-bit DACs, ADCs, and digital. It can generate pulses up to 640 ns duration, and it attains a very low-power readout operation (9.8 mW) compared to its counterparts with 0.5-0.6 dB noise figure, 65–89 dB gain, and -71 dBm maximum TX output power at 4 K. Furthermore, with its duty-cycled mode, the SoC reduces the average power dissipation for the readout application.

European Solid-State Circuits Conference (ESSCIRC)•Sep 19, 2022•16 citations

A Cryo-CMOS 4.5~7GHz Dual-Qubit Homodyne Reflectometer Array with High Q Degenerate Parametric Amplifier Through Dynamic Mode Coupling

Yujie Geng, Haichuan Lin, Bo Wang +1 more

Error-corrected quantum computing does not only require large-scale (106–109) physical Qubit arrays but also relies on high-fidelity, scalable quantum-to-classic interface electronics. Quantum control and readout systems based on cryogenic CMOS integrated circuits mitigate the error of Qubit manipulation, reduce the cabling complexity, and facilitate the quantum feedback, which pave the way towards practical quantum error correction (QEC) and logic quantum gates. RF reflectometry is widely adopted for qubit states readout. Reflectometry conducts Qubit states discrimination (collapsed to “0” or “1”) by detecting the resonant frequency through RF reflection of a high-Q LC tank associated with the sensor Qubit (Fig. 1). The quantum states are encoded in either the amplitude or the phase of the reflected RF signal. Compared with its DC counterpart, the reflectometry achieves unprecedented charge sensitivity, reduces the integration time, and avoids long-term drifting. However, conventional heterodyne reflectometer schemes [1][4][5] adopt sophisticated up/down mixers, ADC, DAC, and PLL for the Qubit excitation and down-mixing, respectively. They suffer from poor TX-RX isolation, inter-modulation, and high DC power, which deteriorate the scalability and readout fidelity. To address these challenges, a highly scalable dual-Qubit homodyne reflectometer array is proposed in this paper. It drives the LC tank by a single PLL and detects the reflection by a high-gain degenerate parametric amplifier (DPA). Along with fast modulation and lock-in detection, it mitigates the interference, complex cabling, and high DC power of conventional heterodyne reflectometers.

IEEE Asian Solid-State Circuits Conference (A-SSCC)•Nov 5, 2023•2 citations

A Cryogenic Superconducting Quantum Computing Unit Interface Chipset With Phase-Detection-Based Readout and Phase-Shifter-Based Controller

Yanshu Guo, Yaoyu Li, Wenqiang Huang +9 more

This article presents a cryogenic quantum interface chipset at 3.5 K for superconducting transmon qubit operations. The chipset comprises a phase-detection readout and a phase-shifter-based polar-modulation controller with flexible scalability. With the proposed phase-detection readout scheme, a 9-bit time-to-digital converter (TDC)-based state detector is used to read out the qubit state by detecting the phase difference between the stimulus signal and the reflected signal. A low-IF N-path filter-based receiver and a multi-tone transmitter are co-designed to enable frequency-division multiplexing (FDM) dispersive readout of multiple qubits. A phase-shifter-based polar-modulation XY-driver is developed with support for fast phase quantum gate operation and derivative-removal-by-adiabatic-gate (DRAG) pulse generation. The Z-driver is realized using a static digital-to-analog converter (DAC) array and a 10-bit dynamic DAC for power efficiency. Fabricated in a 28-nm bulk CMOS process, the chipset occupies a die area of 4.6 mm2. The readout RX achieves a noise temperature of 40 K with a gain of 45–83 dB and a bandwidth of 1.2 GHz. The readout RX consumes 32% less power than state-of-the-art designs. The measured total readout power for simultaneous detection of two qubits is 12.2 mW, which is the lowest among readouts with a similar integration level. In addition, the controller achieves a spurious-free dynamic range (SFDR) of 49 dB for a 1-GS/s Z-driver and an SNR of 42 dB for a 1-GS/s XY-driver. The XY-driver consumes 4.3 mW per qubit under active control. Verified with practical transmon qubits, the readout fidelity exceeds 92.6%, approaching that of commercial instruments. A Rabi experiment at 5.61/6.36 MHz, a Ramsey experiment at 4.1 MHz, and a T1 experiment at$9.98~{\mu }$s are also successfully observed using the proposed chipset at 3.5 K.

IEEE Journal of Solid-State Circuits•May 27, 2026•2 citations

A Fully Integrated Cryo-CMOS SoC for State Manipulation, Readout, and High-Speed Gate Pulsing of Spin Qubits

Jong-Seok Park, Sushil Subramanian, Lester F. Lampert +14 more

This article presents a fully integrated Cryo-CMOS system on chip (SoC) for quantum computing. The proposed SoC integrates a radio frequency (RF) pulse modulator for qubit state manipulation, a multi-tone signal generator and a coherent receiver for qubit state readout, and 22 DACs for high-speed voltage pulsing of qubit gates. By adopting frequency division multiplexing and direct digital synthesis (DDS), the RF pulse modulator can control up to 16 qubits over a single RF line, and the readout receiver can detect the state of up to six qubits simultaneously. The proposed SoC also integrates a microcontroller for low latency on-chip signal processing and increased flexibility in implementing quantum instruction sets. A detailed analysis of qubit-state readout fidelity and the impact of finite DAC resolution on two-qubit gate fidelity is also included in this article, together with an electrical specification summary. The SoC is implemented in Intel’s 22 nm FFL fin field-effect transistor (FinFET) process, and it is characterized both at room and 4 K temperatures. The performance of each specific block is measured, with the readout characterized in a loop-back configuration. Generation of the control signals required for a full Rabi oscillation experiment is also demonstrated. This article also describes the cryogenic thermalization techniques used to integrate the SoC in the dilution refrigerator and shows temperature measurements during operation.

IEEE Journal of Solid-State Circuits•Nov 1, 2021•84 citations
This work presents a neural-network augmented cryo-CMOS readout IC for superconducting quantum computing. With the FCNN-based qubit state detector, this IC achieves the ability of real-time qubit readout drift monitoring and adaptive drift mitigation. Adopting the FIR-DSM-based stimulus TX technique, the measured TX power is 2.6mW, which is>1.9x>1.9 \mathrm{x}>1.9xlower than prior designs. Quadrature digital-IF reflected RX is implemented with stimulus pulses synthesis and reflected signal processing, resulting in a fully-functional readout IC with a lowest power of 10.3mW. Verification with a transmon qubit at 4K, this IC achieves a readout fidelity up to 95.6%.
Cryogenic CMOS (cryo-CMOS) support of quantum processors is becoming a necessity to ensure the continuous growth of qubit count, so as to achieve scalable, fault-tolerant quantum computers. The first paper of the session describes an integrated controller for spin qubits that performs state manipulation, readout, and gate pulsing fabricated in 22nm FinFET CMOS technology. The second paper presents a fully integrated SoC for spin qubit interface based on RF reflectometry of quantum dots, all implemented in 40nm CMOS technology, for scalable quantum systems operating at 3.5K. The third paper also focuses on scalable RF based readout of spin qubits for a record 0.17mW/qubit power requirement, operating at 4.2K. The fourth paper proposes a 1GS/s A/D converter for low-power digitization of the signal measured from a qubit readout that achieves a FOM of 15fJ/conv.-step at 4K.
This paper presents a homodyne-demodulation readout IC with continuous-time direct analog integration for superconducting qubits. By integration at the analog frontend, the effective signal-to-noise ratio is efficiently increased, eliminating the need for a high-performance analog-to-digital converter and costly baseband processing for data recovery. The proposed IC, fabricated in 40 nm CMOS, is verified at 4 K in a dilution refrigerator. The readout fidelity, estimated under real-world conditions, is reported to be 99% within 300 ns.
This paper presents a 28 nm cryo-CMOS system-on-chip (SoC) for the dispersive readout of superconducting qubits operating between 6.5-8.1 GHz at 4 K. The SoC includes a quadrature VCO and a full zero-IF transmitter and receiver chain, including 200 MS/s7-bit DACs, ADCs, and digital. It can generate pulses up to 640 ns duration, and it attains a very low-power readout operation (9.8 mW) compared to its counterparts with 0.5-0.6 dB noise figure, 65–89 dB gain, and -71 dBm maximum TX output power at 4 K. Furthermore, with its duty-cycled mode, the SoC reduces the average power dissipation for the readout application.
Error-corrected quantum computing does not only require large-scale (106–109) physical Qubit arrays but also relies on high-fidelity, scalable quantum-to-classic interface electronics. Quantum control and readout systems based on cryogenic CMOS integrated circuits mitigate the error of Qubit manipulation, reduce the cabling complexity, and facilitate the quantum feedback, which pave the way towards practical quantum error correction (QEC) and logic quantum gates. RF reflectometry is widely adopted for qubit states readout. Reflectometry conducts Qubit states discrimination (collapsed to “0” or “1”) by detecting the resonant frequency through RF reflection of a high-Q LC tank associated with the sensor Qubit (Fig. 1). The quantum states are encoded in either the amplitude or the phase of the reflected RF signal. Compared with its DC counterpart, the reflectometry achieves unprecedented charge sensitivity, reduces the integration time, and avoids long-term drifting. However, conventional heterodyne reflectometer schemes [1][4][5] adopt sophisticated up/down mixers, ADC, DAC, and PLL for the Qubit excitation and down-mixing, respectively. They suffer from poor TX-RX isolation, inter-modulation, and high DC power, which deteriorate the scalability and readout fidelity. To address these challenges, a highly scalable dual-Qubit homodyne reflectometer array is proposed in this paper. It drives the LC tank by a single PLL and detects the reflection by a high-gain degenerate parametric amplifier (DPA). Along with fast modulation and lock-in detection, it mitigates the interference, complex cabling, and high DC power of conventional heterodyne reflectometers.
This article presents a cryogenic quantum interface chipset at 3.5 K for superconducting transmon qubit operations. The chipset comprises a phase-detection readout and a phase-shifter-based polar-modulation controller with flexible scalability. With the proposed phase-detection readout scheme, a 9-bit time-to-digital converter (TDC)-based state detector is used to read out the qubit state by detecting the phase difference between the stimulus signal and the reflected signal. A low-IF N-path filter-based receiver and a multi-tone transmitter are co-designed to enable frequency-division multiplexing (FDM) dispersive readout of multiple qubits. A phase-shifter-based polar-modulation XY-driver is developed with support for fast phase quantum gate operation and derivative-removal-by-adiabatic-gate (DRAG) pulse generation. The Z-driver is realized using a static digital-to-analog converter (DAC) array and a 10-bit dynamic DAC for power efficiency. Fabricated in a 28-nm bulk CMOS process, the chipset occupies a die area of 4.6 mm2. The readout RX achieves a noise temperature of 40 K with a gain of 45–83 dB and a bandwidth of 1.2 GHz. The readout RX consumes 32% less power than state-of-the-art designs. The measured total readout power for simultaneous detection of two qubits is 12.2 mW, which is the lowest among readouts with a similar integration level. In addition, the controller achieves a spurious-free dynamic range (SFDR) of 49 dB for a 1-GS/s Z-driver and an SNR of 42 dB for a 1-GS/s XY-driver. The XY-driver consumes 4.3 mW per qubit under active control. Verified with practical transmon qubits, the readout fidelity exceeds 92.6%, approaching that of commercial instruments. A Rabi experiment at 5.61/6.36 MHz, a Ramsey experiment at 4.1 MHz, and a T1 experiment at9.98 μ9.98~{\mu }9.98 μs are also successfully observed using the proposed chipset at 3.5 K.
This article presents a fully integrated Cryo-CMOS system on chip (SoC) for quantum computing. The proposed SoC integrates a radio frequency (RF) pulse modulator for qubit state manipulation, a multi-tone signal generator and a coherent receiver for qubit state readout, and 22 DACs for high-speed voltage pulsing of qubit gates. By adopting frequency division multiplexing and direct digital synthesis (DDS), the RF pulse modulator can control up to 16 qubits over a single RF line, and the readout receiver can detect the state of up to six qubits simultaneously. The proposed SoC also integrates a microcontroller for low latency on-chip signal processing and increased flexibility in implementing quantum instruction sets. A detailed analysis of qubit-state readout fidelity and the impact of finite DAC resolution on two-qubit gate fidelity is also included in this article, together with an electrical specification summary. The SoC is implemented in Intel’s 22 nm FFL fin field-effect transistor (FinFET) process, and it is characterized both at room and 4 K temperatures. The performance of each specific block is measured, with the readout characterized in a loop-back configuration. Generation of the control signals required for a full Rabi oscillation experiment is also demonstrated. This article also describes the cryogenic thermalization techniques used to integrate the SoC in the dilution refrigerator and shows temperature measurements during operation.