Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEEE Solid-State Circuits Letters

A Cryo-CMOS Homodyne-Demodulation Qubit Readout IC With Continuous-Time Analog Integration for SNR Improvement

Donggyu Minn, Kiseo Kang, Jaeho Lee, Jae‐Yoon Sim

Published Jan 1, 2023• 7 citations
Publisher

Abstract

This paper presents a homodyne-demodulation readout IC with continuous-time direct analog integration for superconducting qubits. By integration at the analog frontend, the effective signal-to-noise ratio is efficiently increased, eliminating the need for a high-performance analog-to-digital converter and costly baseband processing for data recovery. The proposed IC, fabricated in 40 nm CMOS, is verified at 4 K in a dilution refrigerator. The readout fidelity, estimated under real-world conditions, is reported to be 99% within 300 ns.

DOI
10.1109/lssc.2023.3307456

Related papers

A 40 nm Cryo-CMOS Homodyne-Demodulation Readout SoC for Superconducting Qubits

Donggyu Minn, Kiseo Kang, Jaeho Lee +4 more

This paper presents a cryo-CMOS readout SoC based on a homodyne demodulation architecture with an integrating receiver. The homodyne receiver module for each qubit employs a dedicated local LO generator for a coherent detection under a frequency-division multiplexed multi-qubit readout environment. To mitigate the conventional issues of the homodyne demodulation in wireless communications, such as 1/f noise and DC offset by LO leakage, the proposed receiver incorporates effective calibration schemes by utilizing the specific operating conditions of the superconducting qubits. The implemented chip in 40 nm CMOS is tested at 4 K in a dilution refrigerator under an emulated SNR environment of superconducting qubit readout, i.e. -70 dBm input with a noise floor of -148 dBm/Hz. Measurement shows that circuit-only fidelity reaches 99% in 200 ns with an ideal single tone RF input. A back-to-back test using an on-chip 4-tone transmitter shows a 93 % circuit-only fidelity with 400 ns integration.

IEEE Transactions on Circuits and Systems I Regular Papers•Dec 20, 2024•5 citations

A Cryo-CMOS Fully-Integrated Superconducting Qubit Reflectometry Readout IC with FCNN-Based Adaptive Drift Mitigation and FIR-DSM-Based Stimulus TX

Yanshu Guo, Heyue Li, Xicheng Zhang +9 more

This work presents a neural-network augmented cryo-CMOS readout IC for superconducting quantum computing. With the FCNN-based qubit state detector, this IC achieves the ability of real-time qubit readout drift monitoring and adaptive drift mitigation. Adopting the FIR-DSM-based stimulus TX technique, the measured TX power is 2.6mW, which is$>1.9 \mathrm{x}$lower than prior designs. Quadrature digital-IF reflected RX is implemented with stimulus pulses synthesis and reflected signal processing, resulting in a fully-functional readout IC with a lowest power of 10.3mW. Verification with a transmon qubit at 4K, this IC achieves a readout fidelity up to 95.6%.

IEEE Symposium on VLSI Technology and Circuits (VLSI Technology and Circuits)•Jun 14, 2026•0 citations

A Reconfigurable Analog Baseband for Superconducting Qubit Readout

Tian Tian, Yanshu Guo, Zhihua Wang +2 more

Superconducting qubits are promising candidates for building scalable quantum computers, but they require efficient and flexible readout systems that operate at cryogenic temperatures. This article presents a cryo-CMOS analog baseband (ABB) for superconducting qubits readout, which targets flexibly reconfigurable gain, center frequency, and bandwidth. The ABB achieves power and area reduction by integrating programmable-gain amplifiers and filters in one block and by using differential capacitors rather than single-ended ones. The differential-mode gain and common-mode stability of the low-pass filter are improved by negative-impedance inverters. Implemented in 28-nm Bulk CMOS technology, the ABB occupies an active area of 0.016 mm2. It has a tunable gain range from 10.7 to 42.5 dB, a center frequency from 101 to 189 MHz, and a bandwidth from 1.3 to 2.8 MHz. Thus, the ABB enables high-fidelity and low-power readout of superconducting qubits for future large-scale quantum computers.

IEEE MTT-S International Wireless Symposium (IWS)•May 16, 2024•0 citations

A Digital Baseband ASIC Targeting 99.999% Fidelity for Qubit Control and Readout with ROI-based Classification

Heyue Li, Xicheng Zhang, Tian Tian +6 more

As superconducting qubits scale toward large-scale quantum processors, conventional room-temperature (RT) control and readout architectures introduce interconnect bottlenecks that lead to high latency. To mitigate these issues, a cryogenic circuit architecture is adopted that co-integrates control and readout circuits with qubit chips within a cryo-environment. However, this approach is constrained by refrigerator limitations, which impose stringent requirements on area and power dissipation, while high-fidelity qubit operation necessitates high spectral purity. A 28 nm bulk-CMOS digital baseband ASIC is presented for qubit control and readout, integrating a pulse modulator capable of arbitrary-envelope modulation, a readout receiver with a state classifier for reflectometry-signal preprocessing, and on-chip state classification after offline training. Key techniques include (i) a multiplier-less CORDIC-based Direct Digital Synthesis (DDS) for high-precision pulse shaping, which replaces conventional LUT-based implementations and achieves a 29.2% higher speed and a 41.54% lower area compared to conventional LUT-based DDS, with SFDR > 54dB; (ii) a dynamic Region of Interest (ROI) based data cleansing method that classifies the qubit states from a small data subset, reducing memory requirements by 89% compared to conventional threshold classification approaches, while ensuring fidelity degradation is no more than 0.32% compared to the theoretical limit.

IEEE International Symposium on Circuits and Systems proceedings•May 24, 2026•0 citations

A Fully Integrated Cryo-CMOS SoC for State Manipulation, Readout, and High-Speed Gate Pulsing of Spin Qubits

Jong-Seok Park, Sushil Subramanian, Lester F. Lampert +14 more

This article presents a fully integrated Cryo-CMOS system on chip (SoC) for quantum computing. The proposed SoC integrates a radio frequency (RF) pulse modulator for qubit state manipulation, a multi-tone signal generator and a coherent receiver for qubit state readout, and 22 DACs for high-speed voltage pulsing of qubit gates. By adopting frequency division multiplexing and direct digital synthesis (DDS), the RF pulse modulator can control up to 16 qubits over a single RF line, and the readout receiver can detect the state of up to six qubits simultaneously. The proposed SoC also integrates a microcontroller for low latency on-chip signal processing and increased flexibility in implementing quantum instruction sets. A detailed analysis of qubit-state readout fidelity and the impact of finite DAC resolution on two-qubit gate fidelity is also included in this article, together with an electrical specification summary. The SoC is implemented in Intel’s 22 nm FFL fin field-effect transistor (FinFET) process, and it is characterized both at room and 4 K temperatures. The performance of each specific block is measured, with the readout characterized in a loop-back configuration. Generation of the control signals required for a full Rabi oscillation experiment is also demonstrated. This article also describes the cryogenic thermalization techniques used to integrate the SoC in the dilution refrigerator and shows temperature measurements during operation.

IEEE Journal of Solid-State Circuits•Nov 1, 2021•84 citations

A 4.2mW 4K 6-8GHz CMOS LNA for Superconducting Qubit Readout

Alican Çağlar, Steven Van Winckel, S. Brebels +2 more

Millions of qubits need to be employed in a quantum computer to achieve a fault-tolerant quantum operation. To reduce the complexity in such a large-scale system, the control and readout circuitries have been proposed to be placed at the 4 K stage of dilution refrigerators [1]. CMOS technology is commonly used to leverage its scaling to enable large integration of control and readout circuitries with qubits. However, the high-fidelity readout operations require low noise amplifiers (LNAs) with a noise temperature of a few Kelvins. This necessitates the usage of HEMT and parametric amplifiers [2]. Recently reported CMOS LNAs are still far away from attaining such good performance [3–5]. Thus, this is one of the greatest challenges on the way to the fully integrated CMOS readout. Additionally, due to the limited cooling power of dilution refrigerators, low-power solutions are needed for achieving a very good noise performance at 4 K. This paper presents a 28 nm CMOS LNA for qubit readout, which achieves an order of magnitude power reduction compared to its CMOS counterparts while still providing a similar good noise Figure (NF) performance at 4 K.

IEEE Asian Solid-State Circuits Conference (A-SSCC)•Nov 7, 2021•8 citations
This paper presents a homodyne-demodulation readout IC with continuous-time direct analog integration for superconducting qubits. By integration at the analog frontend, the effective signal-to-noise ratio is efficiently increased, eliminating the need for a high-performance analog-to-digital converter and costly baseband processing for data recovery. The proposed IC, fabricated in 40 nm CMOS, is verified at 4 K in a dilution refrigerator. The readout fidelity, estimated under real-world conditions, is reported to be 99% within 300 ns.
This paper presents a cryo-CMOS readout SoC based on a homodyne demodulation architecture with an integrating receiver. The homodyne receiver module for each qubit employs a dedicated local LO generator for a coherent detection under a frequency-division multiplexed multi-qubit readout environment. To mitigate the conventional issues of the homodyne demodulation in wireless communications, such as 1/f noise and DC offset by LO leakage, the proposed receiver incorporates effective calibration schemes by utilizing the specific operating conditions of the superconducting qubits. The implemented chip in 40 nm CMOS is tested at 4 K in a dilution refrigerator under an emulated SNR environment of superconducting qubit readout, i.e. -70 dBm input with a noise floor of -148 dBm/Hz. Measurement shows that circuit-only fidelity reaches 99% in 200 ns with an ideal single tone RF input. A back-to-back test using an on-chip 4-tone transmitter shows a 93 % circuit-only fidelity with 400 ns integration.
This work presents a neural-network augmented cryo-CMOS readout IC for superconducting quantum computing. With the FCNN-based qubit state detector, this IC achieves the ability of real-time qubit readout drift monitoring and adaptive drift mitigation. Adopting the FIR-DSM-based stimulus TX technique, the measured TX power is 2.6mW, which is>1.9x>1.9 \mathrm{x}>1.9xlower than prior designs. Quadrature digital-IF reflected RX is implemented with stimulus pulses synthesis and reflected signal processing, resulting in a fully-functional readout IC with a lowest power of 10.3mW. Verification with a transmon qubit at 4K, this IC achieves a readout fidelity up to 95.6%.
Superconducting qubits are promising candidates for building scalable quantum computers, but they require efficient and flexible readout systems that operate at cryogenic temperatures. This article presents a cryo-CMOS analog baseband (ABB) for superconducting qubits readout, which targets flexibly reconfigurable gain, center frequency, and bandwidth. The ABB achieves power and area reduction by integrating programmable-gain amplifiers and filters in one block and by using differential capacitors rather than single-ended ones. The differential-mode gain and common-mode stability of the low-pass filter are improved by negative-impedance inverters. Implemented in 28-nm Bulk CMOS technology, the ABB occupies an active area of 0.016 mm2. It has a tunable gain range from 10.7 to 42.5 dB, a center frequency from 101 to 189 MHz, and a bandwidth from 1.3 to 2.8 MHz. Thus, the ABB enables high-fidelity and low-power readout of superconducting qubits for future large-scale quantum computers.
As superconducting qubits scale toward large-scale quantum processors, conventional room-temperature (RT) control and readout architectures introduce interconnect bottlenecks that lead to high latency. To mitigate these issues, a cryogenic circuit architecture is adopted that co-integrates control and readout circuits with qubit chips within a cryo-environment. However, this approach is constrained by refrigerator limitations, which impose stringent requirements on area and power dissipation, while high-fidelity qubit operation necessitates high spectral purity. A 28 nm bulk-CMOS digital baseband ASIC is presented for qubit control and readout, integrating a pulse modulator capable of arbitrary-envelope modulation, a readout receiver with a state classifier for reflectometry-signal preprocessing, and on-chip state classification after offline training. Key techniques include (i) a multiplier-less CORDIC-based Direct Digital Synthesis (DDS) for high-precision pulse shaping, which replaces conventional LUT-based implementations and achieves a 29.2% higher speed and a 41.54% lower area compared to conventional LUT-based DDS, with SFDR > 54dB; (ii) a dynamic Region of Interest (ROI) based data cleansing method that classifies the qubit states from a small data subset, reducing memory requirements by 89% compared to conventional threshold classification approaches, while ensuring fidelity degradation is no more than 0.32% compared to the theoretical limit.
This article presents a fully integrated Cryo-CMOS system on chip (SoC) for quantum computing. The proposed SoC integrates a radio frequency (RF) pulse modulator for qubit state manipulation, a multi-tone signal generator and a coherent receiver for qubit state readout, and 22 DACs for high-speed voltage pulsing of qubit gates. By adopting frequency division multiplexing and direct digital synthesis (DDS), the RF pulse modulator can control up to 16 qubits over a single RF line, and the readout receiver can detect the state of up to six qubits simultaneously. The proposed SoC also integrates a microcontroller for low latency on-chip signal processing and increased flexibility in implementing quantum instruction sets. A detailed analysis of qubit-state readout fidelity and the impact of finite DAC resolution on two-qubit gate fidelity is also included in this article, together with an electrical specification summary. The SoC is implemented in Intel’s 22 nm FFL fin field-effect transistor (FinFET) process, and it is characterized both at room and 4 K temperatures. The performance of each specific block is measured, with the readout characterized in a loop-back configuration. Generation of the control signals required for a full Rabi oscillation experiment is also demonstrated. This article also describes the cryogenic thermalization techniques used to integrate the SoC in the dilution refrigerator and shows temperature measurements during operation.
Millions of qubits need to be employed in a quantum computer to achieve a fault-tolerant quantum operation. To reduce the complexity in such a large-scale system, the control and readout circuitries have been proposed to be placed at the 4 K stage of dilution refrigerators [1]. CMOS technology is commonly used to leverage its scaling to enable large integration of control and readout circuitries with qubits. However, the high-fidelity readout operations require low noise amplifiers (LNAs) with a noise temperature of a few Kelvins. This necessitates the usage of HEMT and parametric amplifiers [2]. Recently reported CMOS LNAs are still far away from attaining such good performance [3–5]. Thus, this is one of the greatest challenges on the way to the fully integrated CMOS readout. Additionally, due to the limited cooling power of dilution refrigerators, low-power solutions are needed for achieving a very good noise performance at 4 K. This paper presents a 28 nm CMOS LNA for qubit readout, which achieves an order of magnitude power reduction compared to its CMOS counterparts while still providing a similar good noise Figure (NF) performance at 4 K.