A cold atom experiment can be used to simulate analogous solid-state systems. This provides the bene�t of having a high degree of control over the system parameters and allowing direct detection methods. Disordered transport is one example of where such a system has much to o�er. This thesis concerns the development of a Bose-Fermi mixture experiment for study of two-dimensional optical lattice systems. To achieve single site resolution of the lattice, the experiment makes use of a double microscope set-up. One microscope provides imaging and the second is used to image a spatial light modulator onto the atomic plane. This provides an extremely versatile potential landscape for a trapped cloud. This thesis presents an overview of the set-up of the experiment including progress towards condensation. Particular focus is given to the design and characterisation of the vacuum system and the combined double microscope and spatial light modulator system. The vacuum system design requires a narrow magneto-optical trapping chamber. A novel epoxy sealing technique has been developed, allowing construction of a chamber of just 36mm thickness whilst maintaining high optical access. To provide illumination for the spatial light modulator a technique for homogenising the output of multi-mode �bre has been developed.
A cold atom experiment can be used to simulate analogous solid-state systems. This provides the bene�t of having a high degree of control over the system parameters and allowing direct detection methods. Disordered transport is one example of where such a system has much to o�er. This thesis concerns the development of a Bose-Fermi mixture experiment for study of two-dimensional optical lattice systems. To achieve single site resolution of the lattice, the experiment makes use of a double microscope set-up. One microscope provides imaging and the second is used to image a spatial light modulator onto the atomic plane. This provides an extremely versatile potential landscape for a trapped cloud. This thesis presents an overview of the set-up of the experiment including progress towards condensation. Particular focus is given to the design and characterisation of the vacuum system and the combined double microscope and spatial light modulator system. The vacuum system design requires a narrow magneto-optical trapping chamber. A novel epoxy sealing technique has been developed, allowing construction of a chamber of just 36mm thickness whilst maintaining high optical access. To provide illumination for the spatial light modulator a technique for homogenising the output of multi-mode �bre has been developed.
This thesis describes the progress achieved towards two goals. One is the construction of a compact magneto-optical trap (MOT) apparatus, used both as a standalone undergraduate laboratory experiment and as part of a public engagement demonstration of cold atom physics. The setup, which utilises a dichroic atomic vapour laser lock (DAVLL) system plus homemade sideband generation electronics, is capable of trapping and cooling up to 8x10⁷ ⁸⁵Rb atoms in a standard six-beam laser cooling scheme. The second goal is the loading of an ultracold ensemble of ⁸⁷Rb atoms into novel optical trap geometries using a phase-only liquid crystal spatial light modulator (LC SLM) for applications to atomtronics and quantum simulation. Details of a double vacuum chamber apparatus, designed to produce the first Bose-Einstein condensates (BECs) at St Andrews, are provided. The setup incorporates a hybrid trap evaporative cooling scheme towards quantum degeneracy and reliably produces BECs of 1.9 10⁵ ⁸⁷Rb atoms. Two computational techniques, developed during the course of this project, are presented with the aim of creating flexible, smooth holographic optical traps. The first method illuminates a single SLM with overlapped, co-propagating light beams of different wavelengths to create a composite optical pattern for atom manipulation. The second uses conjugate gradient minimisation to create exceptionally high fidelity light patterns in both amplitude and phase for light in the output plane. These techniques, combined with the implementation of a light sheet into the experimental setup, are used to trap atoms in both a ring profile and in a set of narrow waveguides connected with a tunnelling barrier.
This thesis presents work towards the realisation of dark solitons in a two-dimensional Bose-Einstein condensate. \nThe technical redesign of two sets of coils, necessary for magnetic trapping of the atom cloud in order to \ncreate a condensate, is reported. Two different types of coil technology are presented, discussed, and used. \nThe fabrication of the coils is described, and each set of coils is characterised. Both sets of coils have been installed on the main experiment and are fully operational. \nA key aspect of this thesis is the development of an optical system capable of achieving resolution on the micrometer scale, which can be used for manipulation of a two-dimensional condensate by the method of phase imprinting. The optical system demagnifes the image on a spatial light modulator and focuses the image on the atom plane. Characterisation of the resolution of the optical system shows that a resolution of 3 µm is achieved. The optical system has successfully been implemented on the main experiment and has been used to manipulate the condensate. \nA two-dimensional BEC of \\(^{87}\\)Rb with 31000 atoms and a temperature of 88 nK is realised in a dipole trap of frequencies ω\\(_x\\) = 2π∙5.8 Hz, ω\\(_y\\)= 2π∙19.1 Hz, ω\\(_z\\)= 2π∙269.4 Hz, with gravity being in the z-direction. The method of phase imprinting is used to create the first observed soliton in a 2D BEC. Preliminary analysis of the soliton velocity, width and curvature is presented.
Since the experimental achievement of Bose-Einstein condensation (BEC) in dilute gases, ultra-cold atom systems have proven to be an unparalleled test bed for condensed matter phenomena. With this in mind, our laboratory set out to build an apparatus for the study of the effects of disorder on condensed matter phase transitions using a BEC loaded into one, two, and three-dimensional lattices. My thesis is divided into two main sections. In the first section I describe in detail the design and construction of our apparatus. Our system is designed to form <super>87<\super>Rb condensates of approximately 10<super>5<\super> atoms. We have three possible experimental science chambers. 1. One can perform 1D lattice experiments in the chamber where the condensate is formed. There is a mirror located in vacuum, which is suitable for this purpose. 2. In a glass chamber one can do 1D, 2D, or 3D lattice experiments. Atoms are loaded into a dipole trap (optical tweezer) prior to condensation and transported approximately 20 cm to the glass cell where optical evaporation is performed to form a BEC. 3. One can transfer, using the same techniques as (2), to a chamber with a multi-channel plate detector for Rydberg atom experiments. The experimental results described in my thesis pertain to situation (1). However, I describe some details of (2) in the construction section. The first experiment presented in my thesis demonstrates the effect of disorder on the time-dependent dynamics of lattice systems. We observe that a small perturbation produces a dramatic change in the adiabaticity criteria for loading a BEC into one-dimensional optical lattice. I conclude with experiments that we expect to perform on this apparatus.
This thesis describes and characterizes a setup to conduct experiments combining the fields of cold atoms and nanophotonics. Furthermore, a series of numerical simulations is employed to deepen of atom transport under experimentally realistic conditions. The study of cold atoms is usually fundamental in nature and a very clean approach to investigate the laws of physics. High purity samples of atoms are cooled down to millikelvins or microkelvins. The potential landscape for the atoms can be carefully controlled using lasers and/or magnetic fields. Since the atoms' responses to electric, magnetic or electromagnetic fields are known with very high fidelity, any deviations to the state the atoms are prepared in can be precisely measured. Nanophotonics is the study of light close to or beyond the diffraction limit. In this region the field-like nature of light starts to play a role. By confining light in sub-wavelength-sized structures, high peak intensities can be achieved, giving rise to exciting non-linear optics phenomena. The strong field gradient that can be created allows, for instance, precise spectroscopy measurements, phase-sensitive sub-wavelength microscopy, as well as producing highly receptive sensing devices. Combining cold atoms and nanophotonics creates strong synergy effects. It gives access to strong coupling of light and matter. The scalability of nanophotonics now extends to atomic physics. Atoms can be trapped, coupled and manipulated at very small length scales, and in large numbers. Moreover, the potential landscape for atoms is highly customizable. The rubidium isotope 87 is used in this setup. A cloud of rubidium atoms is gathered and cooled in a two dimensional magneto-optical trap (MOT). Since the atoms are only cooled in two dimensions, they are free to escape in the third dimension and load a following three dimensional MOT. The atoms are now cooled further, compressed and loaded into an optical dipole trap. This dipole trap transports the atoms close to a sample inside the vacuum chamber. A moving optical lattice, or optical conveyor belt, brings the atoms then close to the sample surface. Now experiments can be conducted, studying the interaction of cold atoms and strongly confined light. The atom transport down to the sample surface shows some unexpected behaviour: the atoms seem to spread through the optical lattice during transport. A combination of microscopic and macroscopic numerical simulations, including genetic algorithms, are used to deepen our understanding of the underlying physics. This also allows us to get access to experimental variables that cannot be directly obtained.
This thesis reports the construction of a novel apparatus for experiments with ultracold atoms in optical lattices: the Fermi gas microscope.Improving upon similar designs for bosonic atoms, our Fermi gas microscope has the novel feature of being able to achieve single-site resolved imaging of fermionic atoms in an optical lattice; specifically, we use fermionic potassium-40, sympathetically cooled by bosonic sodium-23.In this thesis, several milestones on the way to achieving single-site resolution are described and documented.First, we have tested and mounted in place the imaging optics necessary for achieving single-site resolution.We set up separate 3D magnetooptical traps for capturing and cooling both 2 3 Na and 40 K.These species are then trapped simultaneously in a plugged quadrupole magnetic trap and evaporated to degeneracy; we obtain a sodium Bose-Einstein condensate with about a million atoms and a degenerate potassium cloud cooled to colder than 1 puK.Using magnetic transport over a distance of 1 cm, we move the cold cloud of atoms into place under the high-resolution imaging system and capture it in a hybrid magnetic and optical-dipole trap.Further evaporation in this hybrid trap performed by lowering the optical trap depth, and the cooled atoms are immersed in an optical lattice, the setup and calibration of which is also described here.Finally, we cool the atoms with optical molasses beams while in the lattice, with the imaging optics collecting the fluoresence light for high-resolution imaging.With molasses cooling set up, single-site fluoresence imaging of bosons and fermions in the same experimental apparatus is within reach.
This thesis focuses on the construction of an atom trapping system utilising a hybrid trap setup to create a Bose-Einstein Condensate. The system involves a three chamber system, consisting of two magneto-optical traps for initial atom trapping and a science chamber to create and observe a BEC. The alkali metal of choice used in this experiment is ⁸⁷Rb, as it possesses favourable properties to create a BEC. A combination of Zeeman modulation frequency stabilisation and polarisation spectroscopy is used to lock our external-cavity diode laser into the right transition frequency and a tiny open-hardware called a Beaglebone is used to remotely access these controls. Beaglebones are also utilised for a double pass configuration of acousto-optic modulators for their convenient remote access which ultimately becomes the primary parameter for troubleshooting the optical part of the experiment. A standard push beam, with a much lower intensity compared to the MOT beams, is pulsed to transport the atoms from the first MOT chamber to the second MOT chamber. By moving the atom cloud to a much lower atmosphere (≈ 10⁻¹¹Torr), we are able to create a bigger atom cloud with a lower temperature which is essential in creating a BEC.