Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Entropy

Argon Ion Treatment of Multi-Material Layered Surface-Electrode Traps for Noise Mitigation

Deviprasath Palani, Florian Hasse, Philip Kiefer, Frederick Boeckling, Daniel Stick, Dustin A. Hite, Ulrich Warring, Tobias Schaetz

Published Nov 28, 2025• 0 citations
Publisher

Abstract

Electric-field noise near ion-trap electrodes limits motional coherence and represents a key obstacle to scaling trapped-ion quantum systems. Here, we investigate how in situ Ar+ sputtering modifies motional heating and dephasing in multi-material surface-electrode traps. Trapped ions serve as local probes of electric-field fluctuations before and after controlled sputtering cycles. The data reveal a non-monotonic dependence of both the dephasing rate and the electric-field noise on the extent of Ar+ sputtering, with coherence initially improving while heating rates increase, followed by a reversal at longer exposures. This behavior highlights the intricate balance between beneficial surface cleaning and detrimental structural modification, driven by changes in surface morphology, redeposition of sputtered material, and diffusion on the surface, underscoring the complex interplay between surface composition and motional stability in multi-material electrode systems. Post-treatment scanning electron microscopy and energy-dispersive X-ray spectroscopy confirm significant modification of the multilayer structure. Technical noise was independently verified to be well below the observed levels. These findings indicate that in situ sputtering modifies surface properties in ways that can either mitigate or enhance electric-field noise, underscoring the need for precise control of material interfaces in next-generation ion-trap architectures.

DOI
10.3390/e27121208

Related papers

100-Fold Reduction of Electric-Field Noise in an Ion Trap Cleaned with In Situ Argon-Ion-Beam Bombardment

Dustin A. Hite, Yves Colombe, A. C. Wilson +8 more

Motional heating of trapped atomic ions is a major obstacle to their use as quantum bits in a scalable quantum computer. The detailed physical origin of this heating is not well understood, but experimental evidence suggests that it is caused by electric-field noise emanating from the surface of the trap electrodes. In this study, we have investigated the role of adsorbates on the electrodes by identifying contaminant overlayers, implementing an in situ argon-ion-beam cleaning treatment, and measuring ion heating rates before and after treating the trap electrodes' surfaces. We find a 100-fold reduction in heating rate after treatment. The experiments described here are sensitive to low levels of electric-field noise in the MHz frequency range. Therefore, this approach could become a useful tool in surface science that complements established techniques.

arXiv:1112.5419•Physical Review Letters•Sep 4, 2012•187 citations

Treatments of a Surface Ion Trap: A Study of Electric-Field Noise near a Contaminated Metal Surface

Maya Berlin-Udi

All surfaces generate electric-field noise, yet the physical origins of this noise are not well understood. This has been an active area of research in the ion trapping community for the past two decades, as ions are highly sensitive to electric-field fluctuations. With our work, we aim to illuminate the microscopic processes that drive charge dynamics on metal surfaces, so as to enable the engineering of low noise quantum devices. We use single trapped calcium ions as detectors to study the 1/f noise generated by the surfaces of ion traps. We the study this noise by observing how it responds to changes in the properties of the trap surface. The surface properties are altered using treatments including prolonged heating, argon ion milling, and electron bombardment. In situ characterization tools are used to monitor the effects of these treatments. Our measurements are consistent with noise produced by an ensemble of thermally activated fluctuators, so our data is discussed in this context. In this dissertation, we present results from a lengthy series of surface treatment experiments, the majority of which took place on a single aluminum-copper substrate. The results of these experiments indicate that argon ion milling can lower noise both by removing contaminants and by altering the morphology of the trap surface. The effects of morphology are isolated from the effects of contaminant removal via heat treatments, which alter the structure of the surface without changing its chemical composition. Through electron bombardment experiments, we begin an exploration of the relationship between hydrocarbon adsorbate structure and electric-field noise. In addition, we compare the noise characteristics of a set of similarly fabricated traps, and determine that atmosphere exposure has a major impact on noise produced by aluminum-copper films.These experiments establish links between the electric-field noise characteristics and the microscopic properties of a contaminated metal trap surface. The insights we draw in this work can inform the next generation of ion trap engineering, storage, and treatment.

•Jan 1, 2020•1 citation

Evidence for multiple mechanisms underlying surface electric-field noise in ion traps

Jonathon A. Sedlacek, Jules Stuart, D. H. Slichter +4 more

Electric-field noise from ion-trap electrode surfaces can limit the fidelity of multiqubit entangling operations in trapped-ion quantum information processors and can give rise to systematic errors in trapped-ion optical clocks. The underlying mechanism for this noise is unknown, but it has been shown that the noise amplitude can be reduced by energetic ion bombardment, or ``ion milling,'' of the trap electrode surfaces. Using a single trapped $^{88}\mathrm{Sr}^{+}$ ion as a sensor, we investigate the temperature dependence of this noise both before and after ex situ ion milling of the trap electrodes. Making measurements over a trap electrode temperature range of 4 K to 295 K in both sputtered niobium and electroplated gold traps, we see a marked change in the temperature scaling of the electric-field noise after ion milling: power-law behavior in untreated surfaces is transformed to Arrhenius behavior after treatment. The temperature scaling becomes material-dependent after treatment as well, strongly suggesting that different noise mechanisms are at work before and after ion milling. To constrain potential noise mechanisms, we measure the frequency dependence of the electric-field noise, as well as its dependence on ion-electrode distance, for niobium traps at room temperature both before and after ion milling. These scalings are unchanged by ion milling.

arXiv:1809.07761•Physical Review A•Dec 27, 2018•43 citations

van der Waals-corrected density functional study of electric field noise heating in ion traps caused by electrode surface adsorbates

Keith G. Ray, Brenda M. Rubenstein, Wenze Gu +1 more

Abstract In order to realize the full potential of ion trap quantum computers, an improved understanding is required of the motional heating that trapped ions experience. Experimental studies of the temperature-, frequency-, and ion–electrode distance-dependence of the electric field noise responsible for motional heating, as well as the noise before and after ion bombardment cleaning of trap electrodes, suggest that fluctuations of adsorbate dipoles are a likely source of so-called ‘anomalous heating,’ or motional heating of the trapped ions at a rate much higher than the Johnson noise limit. Previous computational studies have investigated how the fluctuation of model adsorbate dipoles affects anomalous heating. However, the way in which specific adsorbates affect the electric field noise has not yet been examined, and an electric dipole model employed in previous studies is only accurate for a small subset of possible adsorbates. Here, we analyze the behavior of both in-plane and out-of-plane vibrational modes of twenty-one adsorbate–electrode combinations within the independent fluctuating dipole model, utilizing accurate first principles computational methods to determine the surface-induced dipole moments. We find the chemical specificity of the adsorbate can change the electric field noise by seven orders of magnitude and specifically that soft in-plane modes of weakly-adsorbed hydrocarbons produce the greatest noise and ion heating. We discuss the dynamics captured by the fluctuating dipole model, namely the adsorbate-dependent turn-on temperature and electric field noise magnitude, and also discuss the model’s failure to reproduce the measured 1/ω noise frequency scaling with a single adsorbate species. We suggest future research directions for improved, quantitatively predictive models based on extensions of the present framework to multiple interacting adsorbates.

arXiv:1810.10199•New Journal of Physics•Apr 11, 2019•10 citations

High temperature studies of electric-field noise in a surface ion trap

Crystal Noel

Electric-field noise is a major limiting factor in the performance of ion traps and other quantum devices. Despite intensive research over the past decade, the nature and cause of electric field noise near surfaces is not well understood. This dissertation reports the high- temperature dependence of electric-field noise above an Al-Cu surface using a trapped 40Ca+ ion as a probe.We employ a novel setup with a surface ion trap mounted on a heater for studies of the temperature dependence of electric-field noise. To characterize the Al-Cu material, we explore the effects of heat treatment through ex situ annealing followed by inspection in a scanning electron microscope. To calibrate the temperature of the trap, we demonstrate the use of thermal imaging for monitoring the temperature of an ion trap in vacuum.The temperature and frequency dependence of electric-field noise above the surface is measured using the heating rate of a single ion in a surface-electrode Paul trap. We find that the heating rate saturates at temperatures greater than 450 K. We find that the frequency dependence shows a 1/f behavior, and has a lower frequency scaling exponent at high temperatures than at room temperature. We show that these results are a reflection of the surface-related noise by eliminating other possible sources of noise.Building on historical data for resistance fluctuations in thin films, we develop the thermally-activated fluctuator model to describe the results. We find that a broad distribution of fluctuators with energy barriers peaked around 0.5 eV accurately models both the temperature and frequency dependence of the electric-field noise measured. We present the interpretation of this model as a way to infer that the cause of electric-field noise in the trap is likely defect motion in the metal surface, connecting the problems faced in ion trapping to a large body of work in solid state physics.

•Jan 1, 2019•0 citations

Measurements of electric field noise and light-inducedcharging in cryogenic surface electrode ion traps; Measurements of electric field noise and light-inducedcharging in Al and Cu surface electrode ion traps at cryogenictemperatures

Nathan S. Lachenmyer

Ion traps provide an excellent tool for controlling and observing the state of a single trapped ion. For this reason, ion traps have been proposed as a possible system for large-scale quantum computation. However, many obstacles must be overcome before quantum computing can become a reality. In particular, perturbations in the electric field due to noise and electrode charging must be reduced to increase coherence of the motional quantum state. Gold has been a popular choice in the past due to its inert properties; however, it is undesirable due its incompatibility with CMOS technology. This has led to increased research into alternative CMOS-compatible materials, such as aluminum and copper. This thesis presents measurements of electric field noise and light-induced charging in aluminum, copper, and gold surface electrode traps. In addition, the effect of oxide growth on field noise and electrode charging is explored by controlling the thickness of aluminum oxide on several aluminum traps. The measurements show that electric field noise can be suppressed in aluminum traps to approximately 10-18 V2 cm-2 Hz-1, matching the noise exhibited in gold traps, and that copper traps exhibit noise within an order of magnitude of that in aluminum and gold. However, the natural oxide of aluminum poses many problems towards high-performance aluminum ion traps. The electric field noise is shown to be strongly dependent on the oxide thickness, increasing the noise by a factor of about 10 until saturation at a thickness of 13 nm. Charging of surface electrodes is shown to be highly dependent upon the material, but the model presented does not match the experimental data and is found to be incomplete. These results indicate that ion traps made out of CMOS-compatible materials can perform as well as more traditional traps fabricated from gold with respect to heating and charging as long as methods are developed for controlling oxide growth.

•Jan 1, 2010•0 citations
Electric-field noise near ion-trap electrodes limits motional coherence and represents a key obstacle to scaling trapped-ion quantum systems. Here, we investigate how in situ Ar+ sputtering modifies motional heating and dephasing in multi-material surface-electrode traps. Trapped ions serve as local probes of electric-field fluctuations before and after controlled sputtering cycles. The data reveal a non-monotonic dependence of both the dephasing rate and the electric-field noise on the extent of Ar+ sputtering, with coherence initially improving while heating rates increase, followed by a reversal at longer exposures. This behavior highlights the intricate balance between beneficial surface cleaning and detrimental structural modification, driven by changes in surface morphology, redeposition of sputtered material, and diffusion on the surface, underscoring the complex interplay between surface composition and motional stability in multi-material electrode systems. Post-treatment scanning electron microscopy and energy-dispersive X-ray spectroscopy confirm significant modification of the multilayer structure. Technical noise was independently verified to be well below the observed levels. These findings indicate that in situ sputtering modifies surface properties in ways that can either mitigate or enhance electric-field noise, underscoring the need for precise control of material interfaces in next-generation ion-trap architectures.
Motional heating of trapped atomic ions is a major obstacle to their use as quantum bits in a scalable quantum computer. The detailed physical origin of this heating is not well understood, but experimental evidence suggests that it is caused by electric-field noise emanating from the surface of the trap electrodes. In this study, we have investigated the role of adsorbates on the electrodes by identifying contaminant overlayers, implementing an in situ argon-ion-beam cleaning treatment, and measuring ion heating rates before and after treating the trap electrodes' surfaces. We find a 100-fold reduction in heating rate after treatment. The experiments described here are sensitive to low levels of electric-field noise in the MHz frequency range. Therefore, this approach could become a useful tool in surface science that complements established techniques.
All surfaces generate electric-field noise, yet the physical origins of this noise are not well understood. This has been an active area of research in the ion trapping community for the past two decades, as ions are highly sensitive to electric-field fluctuations. With our work, we aim to illuminate the microscopic processes that drive charge dynamics on metal surfaces, so as to enable the engineering of low noise quantum devices. We use single trapped calcium ions as detectors to study the 1/f noise generated by the surfaces of ion traps. We the study this noise by observing how it responds to changes in the properties of the trap surface. The surface properties are altered using treatments including prolonged heating, argon ion milling, and electron bombardment. In situ characterization tools are used to monitor the effects of these treatments. Our measurements are consistent with noise produced by an ensemble of thermally activated fluctuators, so our data is discussed in this context. In this dissertation, we present results from a lengthy series of surface treatment experiments, the majority of which took place on a single aluminum-copper substrate. The results of these experiments indicate that argon ion milling can lower noise both by removing contaminants and by altering the morphology of the trap surface. The effects of morphology are isolated from the effects of contaminant removal via heat treatments, which alter the structure of the surface without changing its chemical composition. Through electron bombardment experiments, we begin an exploration of the relationship between hydrocarbon adsorbate structure and electric-field noise. In addition, we compare the noise characteristics of a set of similarly fabricated traps, and determine that atmosphere exposure has a major impact on noise produced by aluminum-copper films.These experiments establish links between the electric-field noise characteristics and the microscopic properties of a contaminated metal trap surface. The insights we draw in this work can inform the next generation of ion trap engineering, storage, and treatment.
Electric-field noise from ion-trap electrode surfaces can limit the fidelity of multiqubit entangling operations in trapped-ion quantum information processors and can give rise to systematic errors in trapped-ion optical clocks. The underlying mechanism for this noise is unknown, but it has been shown that the noise amplitude can be reduced by energetic ion bombardment, or ``ion milling,'' of the trap electrode surfaces. Using a single trapped 88Sr+^{88}\mathrm{Sr}^{+}88Sr+ ion as a sensor, we investigate the temperature dependence of this noise both before and after ex situ ion milling of the trap electrodes. Making measurements over a trap electrode temperature range of 4 K to 295 K in both sputtered niobium and electroplated gold traps, we see a marked change in the temperature scaling of the electric-field noise after ion milling: power-law behavior in untreated surfaces is transformed to Arrhenius behavior after treatment. The temperature scaling becomes material-dependent after treatment as well, strongly suggesting that different noise mechanisms are at work before and after ion milling. To constrain potential noise mechanisms, we measure the frequency dependence of the electric-field noise, as well as its dependence on ion-electrode distance, for niobium traps at room temperature both before and after ion milling. These scalings are unchanged by ion milling.
Abstract In order to realize the full potential of ion trap quantum computers, an improved understanding is required of the motional heating that trapped ions experience. Experimental studies of the temperature-, frequency-, and ion–electrode distance-dependence of the electric field noise responsible for motional heating, as well as the noise before and after ion bombardment cleaning of trap electrodes, suggest that fluctuations of adsorbate dipoles are a likely source of so-called ‘anomalous heating,’ or motional heating of the trapped ions at a rate much higher than the Johnson noise limit. Previous computational studies have investigated how the fluctuation of model adsorbate dipoles affects anomalous heating. However, the way in which specific adsorbates affect the electric field noise has not yet been examined, and an electric dipole model employed in previous studies is only accurate for a small subset of possible adsorbates. Here, we analyze the behavior of both in-plane and out-of-plane vibrational modes of twenty-one adsorbate–electrode combinations within the independent fluctuating dipole model, utilizing accurate first principles computational methods to determine the surface-induced dipole moments. We find the chemical specificity of the adsorbate can change the electric field noise by seven orders of magnitude and specifically that soft in-plane modes of weakly-adsorbed hydrocarbons produce the greatest noise and ion heating. We discuss the dynamics captured by the fluctuating dipole model, namely the adsorbate-dependent turn-on temperature and electric field noise magnitude, and also discuss the model’s failure to reproduce the measured 1/ω noise frequency scaling with a single adsorbate species. We suggest future research directions for improved, quantitatively predictive models based on extensions of the present framework to multiple interacting adsorbates.
Electric-field noise is a major limiting factor in the performance of ion traps and other quantum devices. Despite intensive research over the past decade, the nature and cause of electric field noise near surfaces is not well understood. This dissertation reports the high- temperature dependence of electric-field noise above an Al-Cu surface using a trapped 40Ca+ ion as a probe.We employ a novel setup with a surface ion trap mounted on a heater for studies of the temperature dependence of electric-field noise. To characterize the Al-Cu material, we explore the effects of heat treatment through ex situ annealing followed by inspection in a scanning electron microscope. To calibrate the temperature of the trap, we demonstrate the use of thermal imaging for monitoring the temperature of an ion trap in vacuum.The temperature and frequency dependence of electric-field noise above the surface is measured using the heating rate of a single ion in a surface-electrode Paul trap. We find that the heating rate saturates at temperatures greater than 450 K. We find that the frequency dependence shows a 1/f behavior, and has a lower frequency scaling exponent at high temperatures than at room temperature. We show that these results are a reflection of the surface-related noise by eliminating other possible sources of noise.Building on historical data for resistance fluctuations in thin films, we develop the thermally-activated fluctuator model to describe the results. We find that a broad distribution of fluctuators with energy barriers peaked around 0.5 eV accurately models both the temperature and frequency dependence of the electric-field noise measured. We present the interpretation of this model as a way to infer that the cause of electric-field noise in the trap is likely defect motion in the metal surface, connecting the problems faced in ion trapping to a large body of work in solid state physics.
Ion traps provide an excellent tool for controlling and observing the state of a single trapped ion. For this reason, ion traps have been proposed as a possible system for large-scale quantum computation. However, many obstacles must be overcome before quantum computing can become a reality. In particular, perturbations in the electric field due to noise and electrode charging must be reduced to increase coherence of the motional quantum state. Gold has been a popular choice in the past due to its inert properties; however, it is undesirable due its incompatibility with CMOS technology. This has led to increased research into alternative CMOS-compatible materials, such as aluminum and copper. This thesis presents measurements of electric field noise and light-induced charging in aluminum, copper, and gold surface electrode traps. In addition, the effect of oxide growth on field noise and electrode charging is explored by controlling the thickness of aluminum oxide on several aluminum traps. The measurements show that electric field noise can be suppressed in aluminum traps to approximately 10-18 V2 cm-2 Hz-1, matching the noise exhibited in gold traps, and that copper traps exhibit noise within an order of magnitude of that in aluminum and gold. However, the natural oxide of aluminum poses many problems towards high-performance aluminum ion traps. The electric field noise is shown to be strongly dependent on the oxide thickness, increasing the noise by a factor of about 10 until saturation at a thickness of 13 nm. Charging of surface electrodes is shown to be highly dependent upon the material, but the model presented does not match the experimental data and is found to be incomplete. These results indicate that ion traps made out of CMOS-compatible materials can perform as well as more traditional traps fabricated from gold with respect to heating and charging as long as methods are developed for controlling oxide growth.