Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Treatments of a Surface Ion Trap: A Study of Electric-Field Noise near a Contaminated Metal Surface

Maya Berlin-Udi

Published Jan 1, 2020• 1 citation
OpenAlex

Abstract

All surfaces generate electric-field noise, yet the physical origins of this noise are not well understood. This has been an active area of research in the ion trapping community for the past two decades, as ions are highly sensitive to electric-field fluctuations. With our work, we aim to illuminate the microscopic processes that drive charge dynamics on metal surfaces, so as to enable the engineering of low noise quantum devices. We use single trapped calcium ions as detectors to study the 1/f noise generated by the surfaces of ion traps. We the study this noise by observing how it responds to changes in the properties of the trap surface. The surface properties are altered using treatments including prolonged heating, argon ion milling, and electron bombardment. In situ characterization tools are used to monitor the effects of these treatments. Our measurements are consistent with noise produced by an ensemble of thermally activated fluctuators, so our data is discussed in this context. In this dissertation, we present results from a lengthy series of surface treatment experiments, the majority of which took place on a single aluminum-copper substrate. The results of these experiments indicate that argon ion milling can lower noise both by removing contaminants and by altering the morphology of the trap surface. The effects of morphology are isolated from the effects of contaminant removal via heat treatments, which alter the structure of the surface without changing its chemical composition. Through electron bombardment experiments, we begin an exploration of the relationship between hydrocarbon adsorbate structure and electric-field noise. In addition, we compare the noise characteristics of a set of similarly fabricated traps, and determine that atmosphere exposure has a major impact on noise produced by aluminum-copper films.These experiments establish links between the electric-field noise characteristics and the microscopic properties of a contaminated metal trap surface. The insights we draw in this work can inform the next generation of ion trap engineering, storage, and treatment.

Related papers

Surface noise analysis using a single-ion sensor

Nikos Daniilidis, S. Gerber, G. Bolloten +5 more

We use a single-ion electric-field noise sensor in combination with in situ surface treatment and analysis tools, to investigate the relationship between electric-field noise from metal surfaces in vacuum and the composition of the surface. These experiments are performed in a setup that integrates ion trapping capabilities with surface analysis tools. We find that treatment of an aluminum-copper surface with energetic argon ions significantly reduces the level of room-temperature electric-field noise, but the surface does not need to be atomically clean to show noise levels comparable to those of the best cryogenic traps. The noise levels after treatment are low enough to allow fault-tolerant trapped-ion quantum information processing on a microfabricated surface trap at room temperature.

arXiv:1307.7194•Physical Review B•Jun 20, 2014•74 citations

High temperature studies of electric-field noise in a surface ion trap

Crystal Noel

Electric-field noise is a major limiting factor in the performance of ion traps and other quantum devices. Despite intensive research over the past decade, the nature and cause of electric field noise near surfaces is not well understood. This dissertation reports the high- temperature dependence of electric-field noise above an Al-Cu surface using a trapped 40Ca+ ion as a probe.We employ a novel setup with a surface ion trap mounted on a heater for studies of the temperature dependence of electric-field noise. To characterize the Al-Cu material, we explore the effects of heat treatment through ex situ annealing followed by inspection in a scanning electron microscope. To calibrate the temperature of the trap, we demonstrate the use of thermal imaging for monitoring the temperature of an ion trap in vacuum.The temperature and frequency dependence of electric-field noise above the surface is measured using the heating rate of a single ion in a surface-electrode Paul trap. We find that the heating rate saturates at temperatures greater than 450 K. We find that the frequency dependence shows a 1/f behavior, and has a lower frequency scaling exponent at high temperatures than at room temperature. We show that these results are a reflection of the surface-related noise by eliminating other possible sources of noise.Building on historical data for resistance fluctuations in thin films, we develop the thermally-activated fluctuator model to describe the results. We find that a broad distribution of fluctuators with energy barriers peaked around 0.5 eV accurately models both the temperature and frequency dependence of the electric-field noise measured. We present the interpretation of this model as a way to infer that the cause of electric-field noise in the trap is likely defect motion in the metal surface, connecting the problems faced in ion trapping to a large body of work in solid state physics.

•Jan 1, 2019•0 citations

Probing Electric Field Noise Above Ion Traps from 7–600 K and the Influence of Surface Structure on Noise Levels

Benjamin Saarel

Electric field noise produced by the surface of ion trap electrodes reduces the fidelity of quantum computing operations. Despite decades of investigation its microscopic origins remain unclear.This thesis investigates the origins of surface electric field noise by examining its dependence on trap temperature. A set of Al-Cu surface Paul traps are fabricated together and sent to MIT Lincoln Labs (MITLL) and the University of California, Berkeley (UCB). MITLL measures noise from 7 K to room temperature above a first trap and UCB measures noise from room temperature to 590 K above a second trap. The noise measurements from the two experiments are combined to study the noise dependence over the full temperature range from 7-590 K. This is the largest temperature range ever studied using a single trap design and connects the temperature ranges used in all previous studies.We find qualitatively different behaviors at low and high temperatures: from 7-430 K we find that the noise follows the same power-law scaling reported in previous cryogenic studies. At temperatures from 430-590 K, we find that the noise increases much more rapidly than predicted by the power-law scaling. We note a particularly sharp rise in noise at 560 K, which is similar to the sharp rise in noise reported in a previous high-temperature study of a different Al-Cu trap. To determine which physical processes are associated with the change in noise at elevated trap temperatures, we investigate how the material state of the trap electrodes changes when they are heated. We find that the primary physical process associated with the change in noise at high temperature is thermally-activated atom diffusion within the films.This thesis also investigates if the surface structure of room-temperature Au ion traps affects noise levels. We use a heat treatment to restructure the surface of the traps and measure the resulting change in noise. We find that the heat treatment leads to significant changes to the surface structure but causes only a modest change to noise levels. This indicates that the heat-induced changes to the surface do not strongly affect noise. We also note that the noise magnitude observed above these Au traps is state-of-the-art for room-temperature, untreated surface ion traps. This noise level can be explained by modeling the contamination that exists on the trap surface as a dielectric with a loss tangent of tan θ ≈ 0.01.Finally, this thesis investigates the origin of elevated noise levels in one region of a Au surface ion trap. We find that micron-sized particles are located where noise levels are highest, indicating that these particles are likely responsible for the noise. We can explain the magnitude, frequency, and distance dependence of the noise if we treat the particles as a lossy dielectric with a loss tangent tan θ ≈ 0.3.

•May 1, 2026•0 citations

100-Fold Reduction of Electric-Field Noise in an Ion Trap Cleaned with In Situ Argon-Ion-Beam Bombardment

Dustin A. Hite, Yves Colombe, A. C. Wilson +8 more

Motional heating of trapped atomic ions is a major obstacle to their use as quantum bits in a scalable quantum computer. The detailed physical origin of this heating is not well understood, but experimental evidence suggests that it is caused by electric-field noise emanating from the surface of the trap electrodes. In this study, we have investigated the role of adsorbates on the electrodes by identifying contaminant overlayers, implementing an in situ argon-ion-beam cleaning treatment, and measuring ion heating rates before and after treating the trap electrodes' surfaces. We find a 100-fold reduction in heating rate after treatment. The experiments described here are sensitive to low levels of electric-field noise in the MHz frequency range. Therefore, this approach could become a useful tool in surface science that complements established techniques.

arXiv:1112.5419•Physical Review Letters•Sep 4, 2012•187 citations

Argon Ion Treatment of Multi-Material Layered Surface-Electrode Traps for Noise Mitigation

Deviprasath Palani, Florian Hasse, Philip Kiefer +5 more

Electric-field noise near ion-trap electrodes limits motional coherence and represents a key obstacle to scaling trapped-ion quantum systems. Here, we investigate how in situ Ar+ sputtering modifies motional heating and dephasing in multi-material surface-electrode traps. Trapped ions serve as local probes of electric-field fluctuations before and after controlled sputtering cycles. The data reveal a non-monotonic dependence of both the dephasing rate and the electric-field noise on the extent of Ar+ sputtering, with coherence initially improving while heating rates increase, followed by a reversal at longer exposures. This behavior highlights the intricate balance between beneficial surface cleaning and detrimental structural modification, driven by changes in surface morphology, redeposition of sputtered material, and diffusion on the surface, underscoring the complex interplay between surface composition and motional stability in multi-material electrode systems. Post-treatment scanning electron microscopy and energy-dispersive X-ray spectroscopy confirm significant modification of the multilayer structure. Technical noise was independently verified to be well below the observed levels. These findings indicate that in situ sputtering modifies surface properties in ways that can either mitigate or enhance electric-field noise, underscoring the need for precise control of material interfaces in next-generation ion-trap architectures.

Entropy•Nov 28, 2025•0 citations

Measurements of electric field noise and light-inducedcharging in cryogenic surface electrode ion traps; Measurements of electric field noise and light-inducedcharging in Al and Cu surface electrode ion traps at cryogenictemperatures

Nathan S. Lachenmyer

Ion traps provide an excellent tool for controlling and observing the state of a single trapped ion. For this reason, ion traps have been proposed as a possible system for large-scale quantum computation. However, many obstacles must be overcome before quantum computing can become a reality. In particular, perturbations in the electric field due to noise and electrode charging must be reduced to increase coherence of the motional quantum state. Gold has been a popular choice in the past due to its inert properties; however, it is undesirable due its incompatibility with CMOS technology. This has led to increased research into alternative CMOS-compatible materials, such as aluminum and copper. This thesis presents measurements of electric field noise and light-induced charging in aluminum, copper, and gold surface electrode traps. In addition, the effect of oxide growth on field noise and electrode charging is explored by controlling the thickness of aluminum oxide on several aluminum traps. The measurements show that electric field noise can be suppressed in aluminum traps to approximately 10-18 V2 cm-2 Hz-1, matching the noise exhibited in gold traps, and that copper traps exhibit noise within an order of magnitude of that in aluminum and gold. However, the natural oxide of aluminum poses many problems towards high-performance aluminum ion traps. The electric field noise is shown to be strongly dependent on the oxide thickness, increasing the noise by a factor of about 10 until saturation at a thickness of 13 nm. Charging of surface electrodes is shown to be highly dependent upon the material, but the model presented does not match the experimental data and is found to be incomplete. These results indicate that ion traps made out of CMOS-compatible materials can perform as well as more traditional traps fabricated from gold with respect to heating and charging as long as methods are developed for controlling oxide growth.

•Jan 1, 2010•0 citations
All surfaces generate electric-field noise, yet the physical origins of this noise are not well understood. This has been an active area of research in the ion trapping community for the past two decades, as ions are highly sensitive to electric-field fluctuations. With our work, we aim to illuminate the microscopic processes that drive charge dynamics on metal surfaces, so as to enable the engineering of low noise quantum devices. We use single trapped calcium ions as detectors to study the 1/f noise generated by the surfaces of ion traps. We the study this noise by observing how it responds to changes in the properties of the trap surface. The surface properties are altered using treatments including prolonged heating, argon ion milling, and electron bombardment. In situ characterization tools are used to monitor the effects of these treatments. Our measurements are consistent with noise produced by an ensemble of thermally activated fluctuators, so our data is discussed in this context. In this dissertation, we present results from a lengthy series of surface treatment experiments, the majority of which took place on a single aluminum-copper substrate. The results of these experiments indicate that argon ion milling can lower noise both by removing contaminants and by altering the morphology of the trap surface. The effects of morphology are isolated from the effects of contaminant removal via heat treatments, which alter the structure of the surface without changing its chemical composition. Through electron bombardment experiments, we begin an exploration of the relationship between hydrocarbon adsorbate structure and electric-field noise. In addition, we compare the noise characteristics of a set of similarly fabricated traps, and determine that atmosphere exposure has a major impact on noise produced by aluminum-copper films.These experiments establish links between the electric-field noise characteristics and the microscopic properties of a contaminated metal trap surface. The insights we draw in this work can inform the next generation of ion trap engineering, storage, and treatment.
We use a single-ion electric-field noise sensor in combination with in situ surface treatment and analysis tools, to investigate the relationship between electric-field noise from metal surfaces in vacuum and the composition of the surface. These experiments are performed in a setup that integrates ion trapping capabilities with surface analysis tools. We find that treatment of an aluminum-copper surface with energetic argon ions significantly reduces the level of room-temperature electric-field noise, but the surface does not need to be atomically clean to show noise levels comparable to those of the best cryogenic traps. The noise levels after treatment are low enough to allow fault-tolerant trapped-ion quantum information processing on a microfabricated surface trap at room temperature.
Electric-field noise is a major limiting factor in the performance of ion traps and other quantum devices. Despite intensive research over the past decade, the nature and cause of electric field noise near surfaces is not well understood. This dissertation reports the high- temperature dependence of electric-field noise above an Al-Cu surface using a trapped 40Ca+ ion as a probe.We employ a novel setup with a surface ion trap mounted on a heater for studies of the temperature dependence of electric-field noise. To characterize the Al-Cu material, we explore the effects of heat treatment through ex situ annealing followed by inspection in a scanning electron microscope. To calibrate the temperature of the trap, we demonstrate the use of thermal imaging for monitoring the temperature of an ion trap in vacuum.The temperature and frequency dependence of electric-field noise above the surface is measured using the heating rate of a single ion in a surface-electrode Paul trap. We find that the heating rate saturates at temperatures greater than 450 K. We find that the frequency dependence shows a 1/f behavior, and has a lower frequency scaling exponent at high temperatures than at room temperature. We show that these results are a reflection of the surface-related noise by eliminating other possible sources of noise.Building on historical data for resistance fluctuations in thin films, we develop the thermally-activated fluctuator model to describe the results. We find that a broad distribution of fluctuators with energy barriers peaked around 0.5 eV accurately models both the temperature and frequency dependence of the electric-field noise measured. We present the interpretation of this model as a way to infer that the cause of electric-field noise in the trap is likely defect motion in the metal surface, connecting the problems faced in ion trapping to a large body of work in solid state physics.
Electric field noise produced by the surface of ion trap electrodes reduces the fidelity of quantum computing operations. Despite decades of investigation its microscopic origins remain unclear.This thesis investigates the origins of surface electric field noise by examining its dependence on trap temperature. A set of Al-Cu surface Paul traps are fabricated together and sent to MIT Lincoln Labs (MITLL) and the University of California, Berkeley (UCB). MITLL measures noise from 7 K to room temperature above a first trap and UCB measures noise from room temperature to 590 K above a second trap. The noise measurements from the two experiments are combined to study the noise dependence over the full temperature range from 7-590 K. This is the largest temperature range ever studied using a single trap design and connects the temperature ranges used in all previous studies.We find qualitatively different behaviors at low and high temperatures: from 7-430 K we find that the noise follows the same power-law scaling reported in previous cryogenic studies. At temperatures from 430-590 K, we find that the noise increases much more rapidly than predicted by the power-law scaling. We note a particularly sharp rise in noise at 560 K, which is similar to the sharp rise in noise reported in a previous high-temperature study of a different Al-Cu trap. To determine which physical processes are associated with the change in noise at elevated trap temperatures, we investigate how the material state of the trap electrodes changes when they are heated. We find that the primary physical process associated with the change in noise at high temperature is thermally-activated atom diffusion within the films.This thesis also investigates if the surface structure of room-temperature Au ion traps affects noise levels. We use a heat treatment to restructure the surface of the traps and measure the resulting change in noise. We find that the heat treatment leads to significant changes to the surface structure but causes only a modest change to noise levels. This indicates that the heat-induced changes to the surface do not strongly affect noise. We also note that the noise magnitude observed above these Au traps is state-of-the-art for room-temperature, untreated surface ion traps. This noise level can be explained by modeling the contamination that exists on the trap surface as a dielectric with a loss tangent of tan θ ≈ 0.01.Finally, this thesis investigates the origin of elevated noise levels in one region of a Au surface ion trap. We find that micron-sized particles are located where noise levels are highest, indicating that these particles are likely responsible for the noise. We can explain the magnitude, frequency, and distance dependence of the noise if we treat the particles as a lossy dielectric with a loss tangent tan θ ≈ 0.3.
Motional heating of trapped atomic ions is a major obstacle to their use as quantum bits in a scalable quantum computer. The detailed physical origin of this heating is not well understood, but experimental evidence suggests that it is caused by electric-field noise emanating from the surface of the trap electrodes. In this study, we have investigated the role of adsorbates on the electrodes by identifying contaminant overlayers, implementing an in situ argon-ion-beam cleaning treatment, and measuring ion heating rates before and after treating the trap electrodes' surfaces. We find a 100-fold reduction in heating rate after treatment. The experiments described here are sensitive to low levels of electric-field noise in the MHz frequency range. Therefore, this approach could become a useful tool in surface science that complements established techniques.
Electric-field noise near ion-trap electrodes limits motional coherence and represents a key obstacle to scaling trapped-ion quantum systems. Here, we investigate how in situ Ar+ sputtering modifies motional heating and dephasing in multi-material surface-electrode traps. Trapped ions serve as local probes of electric-field fluctuations before and after controlled sputtering cycles. The data reveal a non-monotonic dependence of both the dephasing rate and the electric-field noise on the extent of Ar+ sputtering, with coherence initially improving while heating rates increase, followed by a reversal at longer exposures. This behavior highlights the intricate balance between beneficial surface cleaning and detrimental structural modification, driven by changes in surface morphology, redeposition of sputtered material, and diffusion on the surface, underscoring the complex interplay between surface composition and motional stability in multi-material electrode systems. Post-treatment scanning electron microscopy and energy-dispersive X-ray spectroscopy confirm significant modification of the multilayer structure. Technical noise was independently verified to be well below the observed levels. These findings indicate that in situ sputtering modifies surface properties in ways that can either mitigate or enhance electric-field noise, underscoring the need for precise control of material interfaces in next-generation ion-trap architectures.
Ion traps provide an excellent tool for controlling and observing the state of a single trapped ion. For this reason, ion traps have been proposed as a possible system for large-scale quantum computation. However, many obstacles must be overcome before quantum computing can become a reality. In particular, perturbations in the electric field due to noise and electrode charging must be reduced to increase coherence of the motional quantum state. Gold has been a popular choice in the past due to its inert properties; however, it is undesirable due its incompatibility with CMOS technology. This has led to increased research into alternative CMOS-compatible materials, such as aluminum and copper. This thesis presents measurements of electric field noise and light-induced charging in aluminum, copper, and gold surface electrode traps. In addition, the effect of oxide growth on field noise and electrode charging is explored by controlling the thickness of aluminum oxide on several aluminum traps. The measurements show that electric field noise can be suppressed in aluminum traps to approximately 10-18 V2 cm-2 Hz-1, matching the noise exhibited in gold traps, and that copper traps exhibit noise within an order of magnitude of that in aluminum and gold. However, the natural oxide of aluminum poses many problems towards high-performance aluminum ion traps. The electric field noise is shown to be strongly dependent on the oxide thickness, increasing the noise by a factor of about 10 until saturation at a thickness of 13 nm. Charging of surface electrodes is shown to be highly dependent upon the material, but the model presented does not match the experimental data and is found to be incomplete. These results indicate that ion traps made out of CMOS-compatible materials can perform as well as more traditional traps fabricated from gold with respect to heating and charging as long as methods are developed for controlling oxide growth.