Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

IEICE Electronics Express

Signal matching from SFQ/DC converter to SiGe BiCMOS interface

Zhichao Chen, Lingyun Li, Lixing You

Published May 15, 2025• 1 citation
Publisher

Abstract

Superconducting computers can be realized using a Josephson-CMOS hybrid structure, combining the high speed and low power of single-flux quantum (SFQ) logic with the high integration density of CMOS technology. However, reliable interconnection between SFQ and CMOS circuits at cryogenic temperatures remains challenging due to low signal-to-noise ratio (SNR) and interference. To address these challenges, we propose a DC-biased SiGe BiCMOS interface that converts the 0.2 mV output of the SFQ/DC converter (Q2D) to 1.2 V for CMOS memory. A high-impedance voltage amplifier (VA) and a low-impedance transimpedance amplifier (TIA) were designed to optimize signal matching with the Q2D. The interfaces were simulated, fabricated, and tested at 4.2 K to evaluate their performance. Both analytical and experimental results demonstrate that the TIA significantly improves the SNR and enhances noise immunity during static random-access memory (SRAM) read/write operations, making it more effective than the VA for signal matching between the Q2D and CMOS circuits. This work presents a practcal solution for SFQ-CMOS interconnection, effectively addressing SNR and interference challenges and contributing to the development of scalable superconducting computing systems.

DOI
10.1587/elex.22.20250196

Related papers

A SFQ-to-CMOS Interface Circuit Based on SiGe BiCMOS for Josephson-CMOS Hybrid System

Zhichao Chen, Xingyu Zhang, Lixing You +1 more

Abstract Conventional interfaces for a Josephson-CMOS hybrid system typically rely on Josephson latching drivers (JLDs) or SQUID (Superconducting Quantum InterferenceDevice) stacks to convert weak signals, which are then connected to additional amplifiers providing outputs of 1.2 V or 1.8 V. JLDs output tens of millivolts but require AC bias and precise clock alignment. SQUID stacks reach frequencies of tens of GHz but output few millivolts voltages and occupy large area. To address these challenges, an interface based on SiGe BiCMOS(Silicon-Germanium Bipolar Complementary Metal-Oxide-Semiconductor) has been designed, fabricated, and tested. Fabricated using the 130 nm SiGe BiCMOS process, the interface converts 200 μV voltage signals to 1.2 V and consumes only 386 μW per channel at 4.2 K. In low-frequency measurement, the hybrid system supports 21-channel signals conversion without requiring additional CMOS amplifiers, simplifying cryogenic system design. Advantages include eliminating the need for AC bias and clock alignment, while drawbacks like limited speed are also discussed. This technology facilitates the practical application of multichannel superconducting computers and other applications that require efficient signal conversion, making it one of the most promising interface solutions for the hybrid system.

Journal of Low Temperature Physics•Apr 1, 2025•1 citation

Energy Efficient Digital Data Link

Prasana Ravindran, Su-Wei Chang, Wei-Ting Wong +6 more

Efficiently amplifying the high-speed and low-voltage swing outputs of single flux quantum (SFQ) logic to levels that are suitable for interfacing with room temperature electronics has been a long-standing challenge in the field of superconducting electronics. In this work, we investigate the feasibility of using a lossy passive matching network at 4 K, with a pair of differential 100 low-noise amplifiers heatsunk to 18 K and 50 K stages, respectively. The amplifiers were implemented in a 120 nm SiGe BiCMOS technology. The amplification chain is dc coupled and the small-signal link gain was measured to be approximately 48 dB. The power consumption of each of the two amplification stages was 6.3 mW. The chain was measured at 21 K using a high-speed differential nonreturn-to-zero signal having amplitude commensurate with what one would expect from a superconducting circuit, and clean eye diagrams were observed for data rates as high as 30 Gb/s. The chain was also measured when driven from an SFQ/dc interface, with the first gain stage heatsunk to 9 K. In this configuration, clean eye diagrams were observed to 5 Gb/s, with the speed limitation being related to packaging parasitics.

IEEE Transactions on Applied Superconductivity•Dec 7, 2016•7 citations

A compact high frequency voltage amplifier for superconductor–semiconductor logic interface

Sasan Razmkhah, Ali Bozbey, Pascal Febvre

Abstract The many advantages of cryogenically cooled single-flux quantum (SFQ) circuits imply that the high speed and low voltage output signals must be amplified and interfaced with standard electronics. State-of-the-art low-noise and wide-band amplifiers are required to interface with room temperature electronics. One solution is to place preamplifiers at the cryogenic stage, which requires specific semiconductor design and fabrication. However, a more viable and energy-efficient approach is to integrate the pulsed logic circuit output stages with on-chip superconductor preamplifiers. We designed, fabricated, and tested an on-chip compact voltage multiplier integrated with the output stage of SFQ circuits to increase the voltage amplitude of SFQ pulses. The circuit is designed with the same technology as the logic circuit hence its noise level is lower, and it works at higher frequencies compared to complementary metal-oxide semi-conductor amplifiers and due to quantized nature of it there is no added noise. The fabricated circuit has a compact size of 160 µ m × 320 µ m and provides about 10 dB gain with measured 600 µ V output voltage at frequencies up to ∼25 GHz in simulations. By stacking more levels, over 20 dB gain at circuit level is achievable as shown in simulations. Moreover the gain of the superconductor voltage amplifier is quantized and programmable.

arXiv:2011.03625•Superconductor Science and Technology•Jan 22, 2021•14 citations

Design and Implementation of a Single Flux Quantum Logic-Based Memory Controller for Josephson-CMOS Hybrid Memory Systems

Seda Demirhan, Ali Bozbey

Single flux quantum (SFQ) digital circuits have shown the potential for high speed/low power computation applications. Unfortunately, because of the low integration density and low driving capability of SFQ circuits, realizing large-scale memories by using only SFQ circuits is still a challenge. Josephson-CMOS hybrid memory, hybridizing high-speed, low power SFQ circuits, and high-density CMOS memories is already proposed as a solution to the large-scale memory problem in RSFQ digital systems. In this article, an SFQ-based memory controller which works up to 10 GHz clock frequencies is designed for Josephson-CMOS hybrid memory systems. The memory controller acts as a SFQ/CMOS interface between the SFQ circuit and SRAM module and generates the required waveforms for SRAM read and write operations. The circuit which has 4-b data and 2-b address lines is fabricated with AIST 2.5 kA/cm2STP2 process and operations of the circuits are verified. To demonstrate the scalability of the circuit, memory controller was scaled to 8-b data and 13-b address to control of the 64kb SRAM. Operations of the scaled memory controller are verified with analog simulations. Scaled circuit consumes 0.76 mW power in an area of 1.64 mm × 1.60 mm.

IEEE Transactions on Applied Superconductivity•Jul 28, 2020•5 citations

CMOS-to-SFQ Interface Circuits for RZ and NRZ Coded Signals Transformation

Siqi Li, Xiaoping Gao, Huanli Liu +4 more

A hybrid computing system employing the superconductor central processing unit and semiconductor memory is a prospective strategy to boost speed and power performance. Aiming to convert coded signals at room temperature to single-flux-quantum (SFQ) logic signals in a cryogenic environment, this article presents two types of CMOS-to-SFQ interface circuits for return-to-zero (RZ) and nonreturn-to-zero (NRZ) coded signals transformation. One can double the data rate (DDR) of bipolar RZ signals, and the other can decode unipolar and polar NRZ signals. In the simulation using parameters of the SIMIT Nb03 process, both the interface circuits have up to 20 GHz sampling frequency, more than ±30% bias current margin, and tolerance toward 20 dB SNR white noise. The DDR interface circuit can generate SFQ pulses at both edges of 1.4–2.6 mA bipolar RZ signal, and the decoding interface circuit can interpret 0.2–0.6 mA unipolar and polar NRZ signal into SFQ pulses. The test circuits have been fabricated under the SIMIT Nb03 6 kA/cm2process. In low-frequency measurement, the DDR interface circuit can convert 1.4–2.4 mA bipolar RZ signal, and the decoding interface circuit can convert 0.25–0.5 mA unipolar and polar NRZ signal with more than ±30% bias current margin. In high-frequency measurement, the DDR interface circuit shows an ability to convert a 3.33 GHz input signal.

IEEE Transactions on Applied Superconductivity•Mar 18, 2024•3 citations

High Voltage Driver for RSFQ Digital Signal Processor

Igor I. Soloviev, M R Rafique, Henrik Engseth +1 more

We present an Rapid Single Flux Quantum (RSFQ) based high voltage driver (HVD) developed for the first amplification stage of a hybrid semiconductor-superconductor memory interface for the RSFQ digital signal processor. Implementation of the driver allows to eliminate the impedance mismatch between RSFQ and standard 50 Omega input of semiconductor electronics and increases the signal-to-noise ratio to reach reliable signal transmission with sufficiently low bit error rate. The driver design is based on the serial stack of 8 SQUIDs with specially configured ground-cuts that form a quasi-coplanar line with 50 Omega impedance. The impedance of the driver has been extracted using 3D EM simulators that accurately take into account multilayer structure and capacitance to the ground. The circuit has been designed for the Hypres 4.5 kA/cm2process. The driver was simulated numerically in PSCAN. The driver can produce output signal at 1 Gbit/s speed and 2.4 mV signal level that is enough to be sensed by low-noise amplifier on the further amplification stage.

IEEE Transactions on Applied Superconductivity•Jun 1, 2007•12 citations
Superconducting computers can be realized using a Josephson-CMOS hybrid structure, combining the high speed and low power of single-flux quantum (SFQ) logic with the high integration density of CMOS technology. However, reliable interconnection between SFQ and CMOS circuits at cryogenic temperatures remains challenging due to low signal-to-noise ratio (SNR) and interference. To address these challenges, we propose a DC-biased SiGe BiCMOS interface that converts the 0.2 mV output of the SFQ/DC converter (Q2D) to 1.2 V for CMOS memory. A high-impedance voltage amplifier (VA) and a low-impedance transimpedance amplifier (TIA) were designed to optimize signal matching with the Q2D. The interfaces were simulated, fabricated, and tested at 4.2 K to evaluate their performance. Both analytical and experimental results demonstrate that the TIA significantly improves the SNR and enhances noise immunity during static random-access memory (SRAM) read/write operations, making it more effective than the VA for signal matching between the Q2D and CMOS circuits. This work presents a practcal solution for SFQ-CMOS interconnection, effectively addressing SNR and interference challenges and contributing to the development of scalable superconducting computing systems.
Abstract Conventional interfaces for a Josephson-CMOS hybrid system typically rely on Josephson latching drivers (JLDs) or SQUID (Superconducting Quantum InterferenceDevice) stacks to convert weak signals, which are then connected to additional amplifiers providing outputs of 1.2 V or 1.8 V. JLDs output tens of millivolts but require AC bias and precise clock alignment. SQUID stacks reach frequencies of tens of GHz but output few millivolts voltages and occupy large area. To address these challenges, an interface based on SiGe BiCMOS(Silicon-Germanium Bipolar Complementary Metal-Oxide-Semiconductor) has been designed, fabricated, and tested. Fabricated using the 130 nm SiGe BiCMOS process, the interface converts 200 μV voltage signals to 1.2 V and consumes only 386 μW per channel at 4.2 K. In low-frequency measurement, the hybrid system supports 21-channel signals conversion without requiring additional CMOS amplifiers, simplifying cryogenic system design. Advantages include eliminating the need for AC bias and clock alignment, while drawbacks like limited speed are also discussed. This technology facilitates the practical application of multichannel superconducting computers and other applications that require efficient signal conversion, making it one of the most promising interface solutions for the hybrid system.
Efficiently amplifying the high-speed and low-voltage swing outputs of single flux quantum (SFQ) logic to levels that are suitable for interfacing with room temperature electronics has been a long-standing challenge in the field of superconducting electronics. In this work, we investigate the feasibility of using a lossy passive matching network at 4 K, with a pair of differential 100 low-noise amplifiers heatsunk to 18 K and 50 K stages, respectively. The amplifiers were implemented in a 120 nm SiGe BiCMOS technology. The amplification chain is dc coupled and the small-signal link gain was measured to be approximately 48 dB. The power consumption of each of the two amplification stages was 6.3 mW. The chain was measured at 21 K using a high-speed differential nonreturn-to-zero signal having amplitude commensurate with what one would expect from a superconducting circuit, and clean eye diagrams were observed for data rates as high as 30 Gb/s. The chain was also measured when driven from an SFQ/dc interface, with the first gain stage heatsunk to 9 K. In this configuration, clean eye diagrams were observed to 5 Gb/s, with the speed limitation being related to packaging parasitics.
Abstract The many advantages of cryogenically cooled single-flux quantum (SFQ) circuits imply that the high speed and low voltage output signals must be amplified and interfaced with standard electronics. State-of-the-art low-noise and wide-band amplifiers are required to interface with room temperature electronics. One solution is to place preamplifiers at the cryogenic stage, which requires specific semiconductor design and fabrication. However, a more viable and energy-efficient approach is to integrate the pulsed logic circuit output stages with on-chip superconductor preamplifiers. We designed, fabricated, and tested an on-chip compact voltage multiplier integrated with the output stage of SFQ circuits to increase the voltage amplitude of SFQ pulses. The circuit is designed with the same technology as the logic circuit hence its noise level is lower, and it works at higher frequencies compared to complementary metal-oxide semi-conductor amplifiers and due to quantized nature of it there is no added noise. The fabricated circuit has a compact size of 160 µ m × 320 µ m and provides about 10 dB gain with measured 600 µ V output voltage at frequencies up to ∼25 GHz in simulations. By stacking more levels, over 20 dB gain at circuit level is achievable as shown in simulations. Moreover the gain of the superconductor voltage amplifier is quantized and programmable.
Single flux quantum (SFQ) digital circuits have shown the potential for high speed/low power computation applications. Unfortunately, because of the low integration density and low driving capability of SFQ circuits, realizing large-scale memories by using only SFQ circuits is still a challenge. Josephson-CMOS hybrid memory, hybridizing high-speed, low power SFQ circuits, and high-density CMOS memories is already proposed as a solution to the large-scale memory problem in RSFQ digital systems. In this article, an SFQ-based memory controller which works up to 10 GHz clock frequencies is designed for Josephson-CMOS hybrid memory systems. The memory controller acts as a SFQ/CMOS interface between the SFQ circuit and SRAM module and generates the required waveforms for SRAM read and write operations. The circuit which has 4-b data and 2-b address lines is fabricated with AIST 2.5 kA/cm2STP2 process and operations of the circuits are verified. To demonstrate the scalability of the circuit, memory controller was scaled to 8-b data and 13-b address to control of the 64kb SRAM. Operations of the scaled memory controller are verified with analog simulations. Scaled circuit consumes 0.76 mW power in an area of 1.64 mm × 1.60 mm.
A hybrid computing system employing the superconductor central processing unit and semiconductor memory is a prospective strategy to boost speed and power performance. Aiming to convert coded signals at room temperature to single-flux-quantum (SFQ) logic signals in a cryogenic environment, this article presents two types of CMOS-to-SFQ interface circuits for return-to-zero (RZ) and nonreturn-to-zero (NRZ) coded signals transformation. One can double the data rate (DDR) of bipolar RZ signals, and the other can decode unipolar and polar NRZ signals. In the simulation using parameters of the SIMIT Nb03 process, both the interface circuits have up to 20 GHz sampling frequency, more than ±30% bias current margin, and tolerance toward 20 dB SNR white noise. The DDR interface circuit can generate SFQ pulses at both edges of 1.4–2.6 mA bipolar RZ signal, and the decoding interface circuit can interpret 0.2–0.6 mA unipolar and polar NRZ signal into SFQ pulses. The test circuits have been fabricated under the SIMIT Nb03 6 kA/cm2process. In low-frequency measurement, the DDR interface circuit can convert 1.4–2.4 mA bipolar RZ signal, and the decoding interface circuit can convert 0.25–0.5 mA unipolar and polar NRZ signal with more than ±30% bias current margin. In high-frequency measurement, the DDR interface circuit shows an ability to convert a 3.33 GHz input signal.
We present an Rapid Single Flux Quantum (RSFQ) based high voltage driver (HVD) developed for the first amplification stage of a hybrid semiconductor-superconductor memory interface for the RSFQ digital signal processor. Implementation of the driver allows to eliminate the impedance mismatch between RSFQ and standard 50 Omega input of semiconductor electronics and increases the signal-to-noise ratio to reach reliable signal transmission with sufficiently low bit error rate. The driver design is based on the serial stack of 8 SQUIDs with specially configured ground-cuts that form a quasi-coplanar line with 50 Omega impedance. The impedance of the driver has been extracted using 3D EM simulators that accurately take into account multilayer structure and capacitance to the ground. The circuit has been designed for the Hypres 4.5 kA/cm2process. The driver was simulated numerically in PSCAN. The driver can produce output signal at 1 Gbit/s speed and 2.4 mV signal level that is enough to be sensed by low-noise amplifier on the further amplification stage.