Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Low Temperature Physics

A SFQ-to-CMOS Interface Circuit Based on SiGe BiCMOS for Josephson-CMOS Hybrid System

Zhichao Chen, Xingyu Zhang, Lixing You, Lingyun Li

Published Apr 1, 2025• 1 citation
Publisher

Abstract

Abstract Conventional interfaces for a Josephson-CMOS hybrid system typically rely on Josephson latching drivers (JLDs) or SQUID (Superconducting Quantum InterferenceDevice) stacks to convert weak signals, which are then connected to additional amplifiers providing outputs of 1.2 V or 1.8 V. JLDs output tens of millivolts but require AC bias and precise clock alignment. SQUID stacks reach frequencies of tens of GHz but output few millivolts voltages and occupy large area. To address these challenges, an interface based on SiGe BiCMOS(Silicon-Germanium Bipolar Complementary Metal-Oxide-Semiconductor) has been designed, fabricated, and tested. Fabricated using the 130 nm SiGe BiCMOS process, the interface converts 200 μV voltage signals to 1.2 V and consumes only 386 μW per channel at 4.2 K. In low-frequency measurement, the hybrid system supports 21-channel signals conversion without requiring additional CMOS amplifiers, simplifying cryogenic system design. Advantages include eliminating the need for AC bias and clock alignment, while drawbacks like limited speed are also discussed. This technology facilitates the practical application of multichannel superconducting computers and other applications that require efficient signal conversion, making it one of the most promising interface solutions for the hybrid system.

DOI
10.1007/s10909-025-03291-6

Related papers

Signal matching from SFQ/DC converter to SiGe BiCMOS interface

Zhichao Chen, Lingyun Li, Lixing You

Superconducting computers can be realized using a Josephson-CMOS hybrid structure, combining the high speed and low power of single-flux quantum (SFQ) logic with the high integration density of CMOS technology. However, reliable interconnection between SFQ and CMOS circuits at cryogenic temperatures remains challenging due to low signal-to-noise ratio (SNR) and interference. To address these challenges, we propose a DC-biased SiGe BiCMOS interface that converts the 0.2 mV output of the SFQ/DC converter (Q2D) to 1.2 V for CMOS memory. A high-impedance voltage amplifier (VA) and a low-impedance transimpedance amplifier (TIA) were designed to optimize signal matching with the Q2D. The interfaces were simulated, fabricated, and tested at 4.2 K to evaluate their performance. Both analytical and experimental results demonstrate that the TIA significantly improves the SNR and enhances noise immunity during static random-access memory (SRAM) read/write operations, making it more effective than the VA for signal matching between the Q2D and CMOS circuits. This work presents a practcal solution for SFQ-CMOS interconnection, effectively addressing SNR and interference challenges and contributing to the development of scalable superconducting computing systems.

IEICE Electronics Express•May 15, 2025•1 citation

Josephson Latching Driver Designed Using 10-kA/cm Nb Process as Interface for Josephson-CMOS Hybrid Memory

Yuki Hironaka, Nobuyuki Yoshikawa

In this study, we designed, fabricated, and experimentally tested a Josephson latching driver (JLD), a superconductor-to-semiconductor interface circuit for use in Josephson-CMOS hybrid memory, utilizing a 10-kA/cm2Nb process. The JLD is composed of a voltage driver known as a Suzuki stack and a Josephson four-junction logic (4JL) gate that serves as a preamplifier. The basic structure is based on our previous design using the 2.5-kA/cm2Nb process. In this study, we optimized the critical current and the load resistance of the 4JL gate, taking into account the parameters of the Josephson junctions in the 10-kA/cm2process. In experiments with the fabricated test circuit, we confirmed the correct operation of the JLD (bit error rate−11) at a target frequency of 5 GHz. We also confirmed the correct function of multichannel JLDs, which were used as interface circuits in Josephson-CMOS hybrid memory, in a low-frequency test.

IEEE Transactions on Applied Superconductivity•Nov 28, 2024•3 citations

High-Speed Hybrid Superconductor-to-Semiconductor Interface Circuit With Ultra-Low Power Consumption

Thomas Ortlepp, Stephen R. Whiteley, Lizhen Zheng +2 more

Superconductor electronics for high-performance computing and high-speed analog-to-digital converters requires multi-channel digital data links. Most difficult is the amplification of the weak signals from the superconductor circuit to the volt level of semiconductor electronics. We developed a hybrid digital interface based on a Josephson latching driver, the so-called Suzuki stack, and a clocked CMOS comparator. The input can be directly triggered by a single flux quantum pulse and the output provides a 1 V CMOS-level signal. In contrast to existing systems, our interface is optimized for ultra-low-power consumption to enable its application for parallel multi-bit data interfaces. We provide evaluation of various types of Suzuki stacks and various CMOS comparators. We present experimental data on the delay of the overall hybrid interface and the total power consumption. The bit-error rate has been measured to be below 10-12. We will discuss the trade-off among circuit robustness, speed, and power consumption.

IEEE Transactions on Applied Superconductivity•Nov 14, 2012•20 citations

SiGe Integrated Circuit∕SQUID Hybrid Cryogenic Multiplexer for Superconducting Bolometer Array

D. Prêle, Fabrice Voisin, R. Oger +6 more

The development of large superconducting bolometer (Transition Edge Sensor: TES) arrays requires ultra low noise amplification and multiplexing electronics. The use of a first transducer stage such as a SQUID (Superconducting QUantum Interference Device) allows ultimate performance in terms of noise. However, the linearization of the SQUID characteristic requires low noise amplification. Furthermore, to realize a time domain multiplexer with SQUIDs, switched biasing is also needed. We have designed an Integrated Circuit (IC) in standard BiCMOS SiGe technology for the readout and the control of a SQUID multiplexer. It includes a low noise amplifier with multiplexed inputs, switched current sources for SQUIDs, and digital circuit for the addressing with only one room temperature clock signal. We have successfully tested this integrated circuit down to 2 K. To validate the operation of a SQUID multiplexer controlled by this SiGe cryogenic IC, we have developed a 2×2 SQUID hybrid demonstrator. It consists of four commercial SQUIDs connected to a SiGe IC.

AIP conference proceedings•Jan 1, 2009•3 citations

Interfacing Superconductor and Semiconductor Digital Electronics

Yerzhan Mustafa, Selçuk Köse

Interface circuits are the key components that enable the hybrid integration of superconductor and semiconductor digital electronics. The design requirements of superconductor-semiconductor interface circuits vary depending on the application, such as high-performance classical computing, superconducting quantum computing, and digital signal processing. In this survey, various interface circuits are categorized based on the working principle and structure. The superconducting output drivers are explored, which are capable of converting and amplifying, e.g., single flux quantum (SFQ) voltage pulses, to voltage levels that semiconductor circuits can process. Several trade-offs between circuit- and system-level design parameters are examined. Accordingly, parameters such as the data rate, output voltage, power dissipation, layout area, thermal/heat load of cryogenic cables, and bit-error rate are considered.

physics.app-phCross-listedarXiv:2601.09969•Applied Physics Reviews•Jan 16, 2026•3 citations

A compact high frequency voltage amplifier for superconductor–semiconductor logic interface

Sasan Razmkhah, Ali Bozbey, Pascal Febvre

Abstract The many advantages of cryogenically cooled single-flux quantum (SFQ) circuits imply that the high speed and low voltage output signals must be amplified and interfaced with standard electronics. State-of-the-art low-noise and wide-band amplifiers are required to interface with room temperature electronics. One solution is to place preamplifiers at the cryogenic stage, which requires specific semiconductor design and fabrication. However, a more viable and energy-efficient approach is to integrate the pulsed logic circuit output stages with on-chip superconductor preamplifiers. We designed, fabricated, and tested an on-chip compact voltage multiplier integrated with the output stage of SFQ circuits to increase the voltage amplitude of SFQ pulses. The circuit is designed with the same technology as the logic circuit hence its noise level is lower, and it works at higher frequencies compared to complementary metal-oxide semi-conductor amplifiers and due to quantized nature of it there is no added noise. The fabricated circuit has a compact size of 160 µ m × 320 µ m and provides about 10 dB gain with measured 600 µ V output voltage at frequencies up to ∼25 GHz in simulations. By stacking more levels, over 20 dB gain at circuit level is achievable as shown in simulations. Moreover the gain of the superconductor voltage amplifier is quantized and programmable.

arXiv:2011.03625•Superconductor Science and Technology•Jan 22, 2021•14 citations
Abstract Conventional interfaces for a Josephson-CMOS hybrid system typically rely on Josephson latching drivers (JLDs) or SQUID (Superconducting Quantum InterferenceDevice) stacks to convert weak signals, which are then connected to additional amplifiers providing outputs of 1.2 V or 1.8 V. JLDs output tens of millivolts but require AC bias and precise clock alignment. SQUID stacks reach frequencies of tens of GHz but output few millivolts voltages and occupy large area. To address these challenges, an interface based on SiGe BiCMOS(Silicon-Germanium Bipolar Complementary Metal-Oxide-Semiconductor) has been designed, fabricated, and tested. Fabricated using the 130 nm SiGe BiCMOS process, the interface converts 200 μV voltage signals to 1.2 V and consumes only 386 μW per channel at 4.2 K. In low-frequency measurement, the hybrid system supports 21-channel signals conversion without requiring additional CMOS amplifiers, simplifying cryogenic system design. Advantages include eliminating the need for AC bias and clock alignment, while drawbacks like limited speed are also discussed. This technology facilitates the practical application of multichannel superconducting computers and other applications that require efficient signal conversion, making it one of the most promising interface solutions for the hybrid system.
Superconducting computers can be realized using a Josephson-CMOS hybrid structure, combining the high speed and low power of single-flux quantum (SFQ) logic with the high integration density of CMOS technology. However, reliable interconnection between SFQ and CMOS circuits at cryogenic temperatures remains challenging due to low signal-to-noise ratio (SNR) and interference. To address these challenges, we propose a DC-biased SiGe BiCMOS interface that converts the 0.2 mV output of the SFQ/DC converter (Q2D) to 1.2 V for CMOS memory. A high-impedance voltage amplifier (VA) and a low-impedance transimpedance amplifier (TIA) were designed to optimize signal matching with the Q2D. The interfaces were simulated, fabricated, and tested at 4.2 K to evaluate their performance. Both analytical and experimental results demonstrate that the TIA significantly improves the SNR and enhances noise immunity during static random-access memory (SRAM) read/write operations, making it more effective than the VA for signal matching between the Q2D and CMOS circuits. This work presents a practcal solution for SFQ-CMOS interconnection, effectively addressing SNR and interference challenges and contributing to the development of scalable superconducting computing systems.
In this study, we designed, fabricated, and experimentally tested a Josephson latching driver (JLD), a superconductor-to-semiconductor interface circuit for use in Josephson-CMOS hybrid memory, utilizing a 10-kA/cm2Nb process. The JLD is composed of a voltage driver known as a Suzuki stack and a Josephson four-junction logic (4JL) gate that serves as a preamplifier. The basic structure is based on our previous design using the 2.5-kA/cm2Nb process. In this study, we optimized the critical current and the load resistance of the 4JL gate, taking into account the parameters of the Josephson junctions in the 10-kA/cm2process. In experiments with the fabricated test circuit, we confirmed the correct operation of the JLD (bit error rate−11) at a target frequency of 5 GHz. We also confirmed the correct function of multichannel JLDs, which were used as interface circuits in Josephson-CMOS hybrid memory, in a low-frequency test.
Superconductor electronics for high-performance computing and high-speed analog-to-digital converters requires multi-channel digital data links. Most difficult is the amplification of the weak signals from the superconductor circuit to the volt level of semiconductor electronics. We developed a hybrid digital interface based on a Josephson latching driver, the so-called Suzuki stack, and a clocked CMOS comparator. The input can be directly triggered by a single flux quantum pulse and the output provides a 1 V CMOS-level signal. In contrast to existing systems, our interface is optimized for ultra-low-power consumption to enable its application for parallel multi-bit data interfaces. We provide evaluation of various types of Suzuki stacks and various CMOS comparators. We present experimental data on the delay of the overall hybrid interface and the total power consumption. The bit-error rate has been measured to be below 10-12. We will discuss the trade-off among circuit robustness, speed, and power consumption.
The development of large superconducting bolometer (Transition Edge Sensor: TES) arrays requires ultra low noise amplification and multiplexing electronics. The use of a first transducer stage such as a SQUID (Superconducting QUantum Interference Device) allows ultimate performance in terms of noise. However, the linearization of the SQUID characteristic requires low noise amplification. Furthermore, to realize a time domain multiplexer with SQUIDs, switched biasing is also needed. We have designed an Integrated Circuit (IC) in standard BiCMOS SiGe technology for the readout and the control of a SQUID multiplexer. It includes a low noise amplifier with multiplexed inputs, switched current sources for SQUIDs, and digital circuit for the addressing with only one room temperature clock signal. We have successfully tested this integrated circuit down to 2 K. To validate the operation of a SQUID multiplexer controlled by this SiGe cryogenic IC, we have developed a 2×2 SQUID hybrid demonstrator. It consists of four commercial SQUIDs connected to a SiGe IC.
Interface circuits are the key components that enable the hybrid integration of superconductor and semiconductor digital electronics. The design requirements of superconductor-semiconductor interface circuits vary depending on the application, such as high-performance classical computing, superconducting quantum computing, and digital signal processing. In this survey, various interface circuits are categorized based on the working principle and structure. The superconducting output drivers are explored, which are capable of converting and amplifying, e.g., single flux quantum (SFQ) voltage pulses, to voltage levels that semiconductor circuits can process. Several trade-offs between circuit- and system-level design parameters are examined. Accordingly, parameters such as the data rate, output voltage, power dissipation, layout area, thermal/heat load of cryogenic cables, and bit-error rate are considered.
Abstract The many advantages of cryogenically cooled single-flux quantum (SFQ) circuits imply that the high speed and low voltage output signals must be amplified and interfaced with standard electronics. State-of-the-art low-noise and wide-band amplifiers are required to interface with room temperature electronics. One solution is to place preamplifiers at the cryogenic stage, which requires specific semiconductor design and fabrication. However, a more viable and energy-efficient approach is to integrate the pulsed logic circuit output stages with on-chip superconductor preamplifiers. We designed, fabricated, and tested an on-chip compact voltage multiplier integrated with the output stage of SFQ circuits to increase the voltage amplitude of SFQ pulses. The circuit is designed with the same technology as the logic circuit hence its noise level is lower, and it works at higher frequencies compared to complementary metal-oxide semi-conductor amplifiers and due to quantized nature of it there is no added noise. The fabricated circuit has a compact size of 160 µ m × 320 µ m and provides about 10 dB gain with measured 600 µ V output voltage at frequencies up to ∼25 GHz in simulations. By stacking more levels, over 20 dB gain at circuit level is achievable as shown in simulations. Moreover the gain of the superconductor voltage amplifier is quantized and programmable.