Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Scilight

Mitigating signal interferences in quantum computing applications

Katherine De Lange

Published Sep 20, 2024• 0 citations
Publisher

Abstract

The use of a crest factor reduction algorithm suppresses voltage peaks caused by multi-tone microwave signals, potentially allowing for advanced quantum computing applications
DOI
10.1063/10.0030340

Related papers

Two-Tone Response of Radiofrequency Signals Using the Voltage Output of a Superconducting Quantum Interference Filter

P. Caputo, Jörg Tomes, Jörg Oppenländer +4 more

arXiv:cond-mat/0607342•Journal of Superconductivity and Novel Magnetism•Jan 16, 2007•10 citations

Direct Synthesis of Microwave Waveforms for Quantum Computing

James J. Raftery, Andrei Vrajitoarea, Gengyan Zhang +3 more

Bulletin of the American Physical Society•Mar 13, 2017•1 citation

Optimizing multi-tone microwave pulses via phase selection for quantum computing applications

Ryutaro Ohira, R. Matsuda, H. Shiomi +2 more

Multi-tone microwave signals are crucial for advanced quantum computing applications, including frequency-multiplexed qubit control and simultaneous two-qubit gate execution. However, interference among microwave signal components can cause signal amplitudes to surpass the output limits of an arbitrary waveform generator (AWG), hindering the generation of precise signals necessary for accurate qubit manipulation. To address this issue, we introduce a method that adjusts the phase of individual microwave signal components, effectively reducing interference and maintaining signal amplitude within the AWG’s operational range.

Journal of Applied Physics•Sep 20, 2024•7 citations

Crest factor optimization of multi-tone signals generated for low-temperature sensor readout

Horacio Arnaldi

Microwave kinetic inductance detectors (MKID) are a growing technology of cryogenic detectors and have a great potential in radio-astronomy and cosmic microwave background (CMB) characterization. A review of the general readout performance requirements for experiments requiring the multiplexing of large arrays (~10.000 pixels) of such cryogenic detectors is presented. The focus is on the crest factor optimization process for proper excitation and readout of these large arrays of detectors. It is shown an algorithm to optimize the phase generation of the carriers to obtain a low crest factor, favoring the dynamic range usage of the electronic chain.

arXiv:2611.17207•Argentine Conference on Electronics (CAE)•Mar 9, 2023•2 citations

Advancements in Quantum Computing for Electrical Engineering: Implications for Circuit Design and Signal Processing

Sandeep Singh, Amandeep Kaur, Yogendra Kumar +7 more

Studies in systems, decision and control•Nov 6, 2025•0 citations

Readout of quantum devices with a sideband microwave interferometer immune to systematic noise

N. Crescini, Eoin G. Kelly, Gian Salis +1 more

The accuracy of microwave measurements is not only critical for applications in telecommunication and radar but also for future quantum computers. Qubit technologies such as superconducting qubits or spin qubits require the detection of minuscule signals, typically achieved by reflecting a microwave tone off a resonator that is coupled to the qubit. Noise from cabling and amplification, e.g., from temperature variations, can be detrimental to readout fidelity. We present an approach to detect phase and amplitude changes of a device under test based on the differential measurement of microwave tones generated by two first-order sidebands of a carrier signal. The two microwave tones are sent through the same cable to the measured device that exhibits a narrow-band response for one sideband and leaves the other unaffected. The reflected sidebands are interfered by down-conversion with the carrier. By choosing the amplitude and phases of the sidebands, suppression of either common-amplitude or common-phase noise can be achieved, allowing for fast, stable measurements of frequency shifts and quality factors of resonators. Test measurements were performed on $\mathrm{NbN}$ superconducting resonators at 25 mK to calibrate and characterize the experimental setup and to study time-dependent fluctuations of their resonance frequency.

arXiv:2303.07018•Physical Review Applied•Oct 27, 2023•0 citations
Multi-tone microwave signals are crucial for advanced quantum computing applications, including frequency-multiplexed qubit control and simultaneous two-qubit gate execution. However, interference among microwave signal components can cause signal amplitudes to surpass the output limits of an arbitrary waveform generator (AWG), hindering the generation of precise signals necessary for accurate qubit manipulation. To address this issue, we introduce a method that adjusts the phase of individual microwave signal components, effectively reducing interference and maintaining signal amplitude within the AWG’s operational range.
Microwave kinetic inductance detectors (MKID) are a growing technology of cryogenic detectors and have a great potential in radio-astronomy and cosmic microwave background (CMB) characterization. A review of the general readout performance requirements for experiments requiring the multiplexing of large arrays (~10.000 pixels) of such cryogenic detectors is presented. The focus is on the crest factor optimization process for proper excitation and readout of these large arrays of detectors. It is shown an algorithm to optimize the phase generation of the carriers to obtain a low crest factor, favoring the dynamic range usage of the electronic chain.
The accuracy of microwave measurements is not only critical for applications in telecommunication and radar but also for future quantum computers. Qubit technologies such as superconducting qubits or spin qubits require the detection of minuscule signals, typically achieved by reflecting a microwave tone off a resonator that is coupled to the qubit. Noise from cabling and amplification, e.g., from temperature variations, can be detrimental to readout fidelity. We present an approach to detect phase and amplitude changes of a device under test based on the differential measurement of microwave tones generated by two first-order sidebands of a carrier signal. The two microwave tones are sent through the same cable to the measured device that exhibits a narrow-band response for one sideband and leaves the other unaffected. The reflected sidebands are interfered by down-conversion with the carrier. By choosing the amplitude and phases of the sidebands, suppression of either common-amplitude or common-phase noise can be achieved, allowing for fast, stable measurements of frequency shifts and quality factors of resonators. Test measurements were performed on NbN\mathrm{NbN}NbN superconducting resonators at 25 mK to calibrate and characterize the experimental setup and to study time-dependent fluctuations of their resonance frequency.